INA849DGKR
Product Specifications
INA849DGKR
Texas Instruments — Power Management & Signal Chain
Product Overview
The INA849DGKR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
INA849DGKR: 1 nV per root hertz instrumentation amplifier with 28 MHz of bandwidth
The INA849DGKR is the low noise member of the instrumentation amplifier family, with 1 nV per root hertz of input voltage noise, 28 MHz of bandwidth at unity gain and 8 MHz at a gain of 100. It is the part that a high resolution converter needs in front of it when the source is a low impedance transducer and the signal is small: a 1 nV amplifier in a 100 kHz bandwidth contributes about 0.3 uV of noise, which is below the resolution of a 24 bit converter over a 5 V range.
Offset is 35 uV maximum with 0.4 uV per degree drift, bias current is 20 nA maximum, and gain drift is 5 ppm per degree at unity gain. The current feedback topology keeps the bandwidth high as the gain rises, which is the opposite of a voltage feedback instrumentation amplifier, and the settling time of 0.4 microseconds to 0.01 per cent is what allows the part to drive a multiplexed converter without a sample and hold.
Key data for the INA849DGKR
| Noise | 1 nV per root hertz typical input voltage noise, the lowest in the family |
| Bandwidth | 28 MHz at unity gain and 8 MHz at a gain of 100, with a 35 V per microsecond slew rate |
| Offset | 35 uV maximum with 0.4 uV per degree maximum drift, bias current 20 nA maximum |
| Rejection | 92 dB at unity gain and 120 dB minimum at maximum gain |
| Settling | 0.4 microseconds to 0.01 per cent, which is what a multiplexed converter needs between channels |
| Supply | 8 V to 36 V single or 4 V to 18 V dual, minus 40 C to 125 C |
Body, marking and reel data
| Body | DGK, 8 pin VSSOP at 3.00 mm by 3.00 mm; an 8 pin SOIC at 4.90 mm by 3.91 mm carries the same die |
| Reel | R suffix is the large reel; the VSSOP body is the one used where the analog front end has to sit close to the converter |
| Gain resistor | One external resistor sets any gain from 1 to 10,000, and its tolerance dominates the gain error above a gain of 100 |
| Supply floor | 8 V minimum single supply, which is higher than the INA819 and means a 5 V system cannot use this part without a boost |
| Document | SBOS945B dated November 2020 and revised April 2021 |
Where 1 nV decides the architecture
The noise floor of a front end sets the resolution that the converter behind it can actually deliver. A 24 bit converter over a 5 V range has a least significant bit of about 0.3 uV, and an amplifier with 20 nV per root hertz in a 10 kHz bandwidth contributes 2 uV, which is six codes of noise. The INA849 at 1 nV contributes 0.1 uV in the same bandwidth, which is below one code, so the converter rather than the amplifier becomes the limit.
The current feedback topology is what makes that noise figure usable at gain. A voltage feedback instrumentation amplifier loses bandwidth in proportion to gain, so a 1 nV part at a gain of 100 would be slow. The INA849 holds 8 MHz at a gain of 100, which keeps a 100 kHz signal intact and lets a fast converter sample it without a settling penalty.
The 8 V supply floor is the constraint. A 12 V or 15 V analog rail is the natural home for this part, and a 5 V system that wants the low noise has to either boost the rail or accept the INA819 at 8 nV. That is a real architectural decision and it should be made before the board is started, because the boost converter that generates the 8 V can itself be a noise source that the front end has to reject. Our amplifier cross reference puts the three instrumentation amplifiers side by side on noise, supply and bandwidth, and the ADC DAC cross reference note covers the converters that usually follow this front end and the settling they require.
Buyer questions on the INA849DGKR
Can it run from a 5 V supply? No, the minimum single supply is 8 V. A 5 V system needs the INA819 or a boosted analog rail.
Does the 1 nV figure apply at every gain? It is the input referred voltage noise, so the output noise rises with gain as expected, and the input figure stays the one to compare against the source impedance.
Why is the settling time specified to 0.01 per cent? Because that is the level a 16 or 18 bit converter needs when it switches channels. A slower settling amplifier forces a longer acquisition window and lowers the achievable sample rate.
Availability and ordering notes
INA849DGKR is the VSSOP-8 member of the family, with an SOIC-8 sibling on the same die. The document is a 2020 release revised in 2021, so it is mature. Because the part is chosen for noise, a substitution to a lower noise or lower supply part changes the front end architecture rather than only the BOM line, and a quotation should make that clear.