Contact Us

INA818ID

Brand: Texas Instruments
Texas Instruments INA818ID is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA818ID — Power Management & Signal Chain | Superb Automation

INA818ID

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA818ID from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA818ID: 35 microvolt low noise instrumentation amplifier in a 8-pin SOIC

INA818ID is a precision instrumentation amplifier with protected inputs in a SOIC body of 8 pins. One resistor sets the gain from 1 to 1000 with the 1 plus 50 kiloohm over RG relation, and the part holds 10 microvolts of typical offset, 8 nanovolts per root hertz of noise and 110 dB of rejection at gain 10. The inputs survive 60 volts above or below the rails, which is what separates it from an op amp based front end.

Order code and package

Order codeINA818ID
Functionprecision instrumentation amplifier
Gain1 to 1000, set by one external resistor
Gain equationG equals 1 plus 50 kiloohms divided by RG
PackageSOIC, 8 pins
Supply4.5 V to 36 V single, plus and minus 2.25 to 18 V
Input protectionplus or minus 60 V beyond the rails
Offset voltage10 microvolts typical, 35 microvolts maximum
Noise8 nanovolts per root hertz
Bandwidth2 MHz at gain 1, 270 kHz at gain 100
Load stabilitystable with 1 nanofarad
DatasheetSBOS902 revision A

Electrical parameters that decide the application

Gain drift5 ppm per C at gain 1, 35 ppm per C above gain 1
Common mode rejection110 dB minimum at gain 10
Power supply rejection100 dB minimum at gain 1
Input bias currentlow enough for a high impedance bridge, protected by the input stage
Outputrail to rail, with a reference pin for level shifting
Temperature rangeminus 40 to plus 125 C
Supply currentmodest for a precision amplifier at this bandwidth
Protection behaviourthe input stage limits current rather than breaking down
Stability1 nanofarad load without a series resistor
Comparisonsecond generation of the classic 8 nanovolt instrumentation amplifier

Points to check before this part goes on a BOM

The gain drift figure splits at gain 1 and above gain 1. Five ppm per C at unity becomes 35 ppm per C as soon as the external resistor sets the gain, so the resistor and its temperature coefficient enter the drift budget at that point.

Sixty volts of input protection is the field cable number. A 24 V loop miswired onto a 5 V board puts the full loop voltage across the input, and an unprotected amplifier fails before the fuse opens.

Eight nanovolts per root hertz is the reason to buy this part rather than a zero drift one. A chopper amplifier reaches lower offset and drift but its noise density is higher, so a wideband low level signal prefers this device.

Common mode rejection of 110 dB is a minimum at gain 10, not at unity. A unity gain application with a large common mode has to read the gain 1 row, where the rejection is lower and the input range is the binding constraint.

Stability into 1 nanofarad without a series resistor is unusual and useful at the converter interface. A switched capacitor input presents exactly that kind of load, so the amplifier can sit directly at the converter pin.

The supply range of 4.5 V to 36 V rules out a 3.3 V rail on a single supply. A 3.3 V system needs a charge pump for the negative rail or a different amplifier, and the current sense line in this catalogue covers 1.8 V to 5.5 V.

Where this order code fits

Industrial transmitters, bridge amplifiers on 24 V loops and any front end that can see a miswired field cable are the boards that use it. Boards comparing it with a neighbouring part start from our Amplifier Cross Reference page, and boards replacing a part that has gone end of life start from the One Stop BOM Sourcing page.

Questions buyers ask

Does the 60 volt protection replace external clamp diodes? It removes the need for them in most field wiring faults, but the current is still limited by the source impedance; a low impedance 60 volt source into the part is a thermal question, not just a voltage one.

Why is the gain drift different at gain 1? At unity the external resistor is out of circuit, so only the die contributes; above unity the resistor and its temperature coefficient add their own term.

SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the Supplier Quality Audit page sets out the checks that keep a substitute from failing on the bench.