INA745BIRELR
Product Specifications
INA745BIRELR
Texas Instruments — Power Management & Signal Chain
Product Overview
The INA745BIRELR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
INA745BIRELR: 40 V, 16 bit power monitor with the shunt in the package
The INA745BIRELR is the 40 V member of the integrated shunt power monitor family, in a 14 pin QFN at 5 mm by 3 mm. The internal shunt is 800 microhm, the continuous current is 35 A at 25 C and the peak measurement window reaches 39.32 A, with a common mode range of minus 0.1 V to 40 V. It reports current, bus voltage, die temperature, power, energy and charge over I2C at 2.94 MHz.
The B grade on this part carries 62.5 mA of offset current, 30 uA per degree of drift, 1.25 per cent of system gain error, 1.6 per cent of power accuracy and 2.1 per cent of energy accuracy at 25 C full scale. The A grade halves the offset to 6.25 mA and tightens the gain to 0.75 per cent, with power at 0.9 per cent and energy at 1.4 per cent. The two grades share the body and the pinout, so the choice is made on the accuracy the end product claims.
Key data for the INA745BIRELR
| Shunt | 800 microhm internal, 35 A continuous at 25 C, peak measurement to 39.32 A |
| Common mode | Minus 0.1 V to 40 V, which covers a 36 V rail and a 24 V battery pack at full charge |
| Converter | 16 bit delta sigma, conversion times from 50 microseconds to 4.12 ms, averaging from 1 to 1024 samples |
| Accuracy on the B grade | Offset current 62.5 mA with 30 uA per degree drift, gain error 1.25 per cent, power 1.6 per cent and energy 2.1 per cent at 25 C full scale |
| Accuracy on the A grade | Offset current 6.25 mA, gain error 0.75 per cent, power 0.9 per cent and energy 1.4 per cent, in the same body |
| Interface and supply | I2C at 2.94 MHz with 16 addresses, 2.7 V to 5.5 V supply, 640 uA typical and 5 uA maximum in shutdown |
Body, marking and reel data
| Body | REL, 14 pin QFN at 5.00 mm by 3.00 mm, a narrower body than the 85 V member's 5 mm by 4 mm |
| Reel | R suffix is the large reel; the current path through the shunt pins is the thermal constraint, so the copper area sets the usable current |
| Grades | A and B share the die, the body and the pinout and differ in the offset current and gain rows |
| Temperature sensor | On die, 1.5 C maximum at 25 C with 2.5 C over the junction range, used for the shunt compensation |
| Document | SBOSAC3B dated July 2023 and revised August 2025, the current revision covering both grades |
Where the 40 V window is the right one
Forty volts covers the common industrial and telecom rails: a 36 V nominal supply, a 24 V battery pack that charges to 29 V, a 28 V aircraft bus and a 12 V or 5 V rail with any transient. The 85 V member exists for 48 V packs and for 60 V transients, but it comes in a larger body and costs more copper, so the 40 V part is the default unless the rail needs the headroom.
The accuracy choice is where the money is decided. The B grade offset current of 62.5 mA is 0.18 per cent of a 35 A full scale, and on a 5 A load it is 1.25 per cent of the reading, which is the dominant error at low current. A product that reports energy for billing needs the A grade, or a part with a smaller shunt and an external amplifier; a product that reports its own consumption for a dashboard does not. That distinction is worth stating in a quotation, because the two grades are otherwise identical on the board.
Because the shunt sits inside the package, the part also removes the tolerance of the copper trace that would otherwise be measured. That is a real advantage on a board where the current path is a pour rather than a component, and it is the reason this family is chosen over a separate monitor even when the current is well below 35 A. Our power management cross reference lists the 40 V and 85 V members with their bodies, and the amplifier cross reference note covers the analog output parts for a board that has an ADC but no bus.
Buyer questions on the INA745BIRELR
Is the A grade available in the same reel size? The grade is a different order code and the reel follows the code, so a mixed A and B requirement is two line items and two reels rather than one.
How much copper does 35 A need? The vendor gives the continuous current at 25 C and the junction to ambient thermal resistance in the package section; the board has to hold the junction below the limit at the ambient of the enclosure, and 1 W in a 5 mm by 3 mm body needs several square centimetres of copper on each layer.
Can the bus voltage be read without current flowing? Yes. The bus converter runs independently of the shunt, so a no load rail still reports its voltage, which is what a supply monitor needs during start up.
Availability and ordering notes
INA745BIRELR is the B grade 40 V integrated shunt monitor in the 5 mm by 3 mm QFN. The A grade is INA745AIRELR in the same body, so a substitution between grades is a reorder and not a board change, but the accuracy claim in the end product has to be re checked against the 6.25 mA and 62.5 mA offset currents. The part is a 2023 release and the revision history shows an August 2025 update, which is a good sign that the silicon is still supported rather than winding down.