INA740BIREMR
Product Specifications
INA740BIREMR
Texas Instruments — Power Management & Signal Chain
Product Overview
The INA740BIREMR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
INA740BIREMR: a 16 bit power monitor with the shunt inside the package
The INA740BIREMR is a digital power monitor that integrates the current sensing element, a 16 bit delta sigma converter and the arithmetic for power, energy and charge in a 14 pin VQFN. The internal shunt is 800 microhm, which carries 35 A continuously at 25 C and measures peaks to 39.32 A, with a common mode range of minus 0.1 V to 85 V.
Putting the shunt inside the package removes the four wire connection that a discrete shunt needs and the Kelvin drop that comes with a poor one. The price is thermal: 35 A through 800 microhm is 0.98 W inside a 5 mm by 4 mm body, which the datasheet handles by specifying the continuous current at 25 C and leaving the derating to the board. The B grade carries 62.5 mA of offset current, 30 uA per degree of drift and 1.25 per cent of system gain error, against 6.25 mA, 0.75 per cent and the same drift on the A grade of the 40 V member.
Key data for the INA740BIREMR
| Shunt | 800 microhm internal, 35 A continuous at 25 C, peak measurement to 39.32 A |
| Common mode | Minus 0.1 V to 85 V, so a 48 V rail sits inside the window with room for a 60 V transient |
| Converter | 16 bit delta sigma with conversion times from 50 microseconds to 4.12 ms and averaging from 1 to 1024 samples |
| Accuracy | Offset current 62.5 mA, offset drift 30 uA per degree, system gain error 1.25 per cent, power accuracy 1.6 per cent at 25 C full scale |
| Energy and charge | 2.1 per cent at 25 C full scale on the B grade, accumulated in the background against a 0.5 per cent oscillator |
| Interface and supply | I2C at 2.94 MHz with 16 pin selectable addresses, 2.7 V to 5.5 V supply, 640 uA typical and 5 uA maximum in shutdown |
Body, marking and reel data
| Body | REM, 14 pin VQFN at 5.00 mm by 4.00 mm, with the current path entering and leaving on the two shunt pins |
| Reel | R suffix is the large reel; the QFN pad has to be soldered to a copper area sized for the 1 W of dissipation at full current |
| Current path | The shunt pins carry the load current, so the copper feeding them is part of the thermal solution and not only a connection |
| Temperature sensor | On die, 1.5 C maximum at 25 C and 2.5 C over the junction range, which is how the part compensates the shunt across temperature |
| Document | SBOSAC1B dated July 2023 and revised December 2025, the current revision |
Where an integrated shunt changes the measurement
A discrete shunt and a separate monitor have two error sources that the integrated part removes: the shunt tolerance and the Kelvin connection. An 800 microhm shunt made of a copper alloy has a temperature coefficient of about 50 ppm per degree unless it is trimmed, and the voltage drop between the shunt terminals and the amplifier input adds to the reading at high current. The INA740B trims the shunt and measures it on die, and the on die temperature sensor lets the part compensate the drift.
The thermal question is the one to settle before a board is committed. At 35 A the package dissipates about 1 W, and the continuous current rating is given at 25 C, so a board that runs at 70 C ambient cannot carry 35 A through this part without a copper area that is larger than the package. The practical answer is to run the part below its rating, which is what the peak measurement window allows: a 30 A working current with a 39.32 A peak leaves room for a transient without touching the thermal limit.
The digital side is what makes the part useful in a system that reports energy rather than current. Power, energy and charge accumulate in the background, so the host reads a register instead of integrating samples, and the 0.5 per cent oscillator keeps that accumulation honest over months. The 16 addresses let several rails share one bus, which is how a server or a power shelf reports each output separately. Our power management cross reference lists the members by shunt value and current rating, and the one stop BOM sourcing note covers how the A and B grades are quoted when only one is in stock.
Buyer questions on the INA740BIREMR
Can the internal shunt be bypassed? No. The current path is through the package, and there is no separate input pair for an external shunt. A board that needs a different shunt value needs a different part.
What is the resolution at 1 A? The converter is 16 bit over the full scale of 39.32 A, so one code is about 0.6 mA before averaging. The offset current of 62.5 mA is the floor that matters more than the code size at low currents.
Does the 85 V rating cover a 48 V battery pack at full charge? A 48 V nominal pack reaches about 58 V at full charge, which is inside the 85 V window with margin. A 72 V pack reaches 84 V and sits at the edge, so the transient has to be checked.
Availability and ordering notes
INA740BIREMR is the B grade of the 85 V integrated shunt monitor in the 14 pin VQFN. The A grade does not exist in this voltage class, so the accuracy at 85 V is the B grade rows, and a customer who needs the tighter offset has to move to the 40 V member. The 5 mm by 4 mm body and the 1 W dissipation mean the footprint and the copper are one decision; a quotation that treats the part as a drop in replacement for a discrete shunt should say so.