INA4290A3IRGVR
Product Specifications
INA4290A3IRGVR
Texas Instruments — Power Management & Signal Chain
Product Overview
The INA4290A3IRGVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
INA4290A3IRGVR: four 100 V/V current sense channels in a 4 mm QFN
The INA4290A3IRGVR is the quad channel, 100 V/V member of the INAx290 family. It puts four independent current sense amplifiers with a 2.7 V to 120 V common mode range into a 16 pin QFN at 4 mm by 4 mm, drawing 370 uA per channel. The A3 gain of 100 V/V is the setting that turns a 0.5 milliohm shunt into 50 mV per ampere, so a 3 V output is reached at 60 A per channel.
Each channel is a complete amplifier with its own output, and the four share only the supply and ground. Offset is 12 uV maximum with 0.2 uV per degree drift, gain error is 0.1 per cent maximum with 5 ppm per degree drift, and the DC common mode rejection is 160 dB typical with 85 dB at 50 kHz. The bandwidth is 1.1 MHz at a 20 V/V gain, which is the figure the family quotes, and the slew rate is 2 V per microsecond.
Key data for the INA4290A3IRGVR
| Channels | Four independent amplifiers, each with its own output pin, sharing one supply and one ground |
| Gain | 100 V/V on the A3 code; the family offers 20, 50, 200 and 500 V/V across single, dual and quad members |
| Common mode | 2.7 V to 120 V operational, minus 20 V to 122 V survival, independent of the 2.7 V to 20 V supply |
| Accuracy | Offset 12 uV maximum with 0.2 uV per degree drift, gain error 0.1 per cent maximum with 5 ppm per degree drift |
| Rejection | 160 dB typical DC common mode rejection and 85 dB at 50 kHz |
| Supply | 2.7 V to 20 V single rail, 370 uA per channel typical, minus 40 C to 125 C |
Body, marking and reel data
| Body | RGV, 16 pin QFN at 4.00 mm by 4.00 mm, the quad body of the family |
| Siblings | The single channel INA290 is in SC-70 at 2.00 mm by 1.25 mm and the dual INA2290 in VSSOP-8 at 3 mm by 3 mm, so the family scales without changing the electrical rows |
| Reel | R suffix is the large reel; the QFN thermal pad has to be soldered to a ground plane that carries the four channel return currents |
| Grounding | Four channels in one body share one ground pin, so the return paths have to be separated on the board rather than inside the package |
| Pin count | Sixteen pins carry four outputs, four input pairs, supply and ground, which leaves no spare pin for a reference or a filter |
Where four channels in one body is worth the shared ground
A three phase motor drive with a shunt in each leg needs three channels, and a fourth channel often monitors the DC link, which is exactly the count this part provides. Putting them in one body removes three packages and their decoupling, and it makes the four readings track, which matters when a controller compares phase currents to detect an imbalance. The 120 V common mode range covers a 48 V bus with margin and reaches a 96 V pack at nominal.
The shared ground is the detail that decides whether the quad is better than four singles. Each channel measures a small differential voltage in the presence of a large common mode, and the return current of one channel flows through the shared ground pin. Keeping the four return paths separate to the star point, and returning the QFN pad to that point rather than to a digital ground, keeps the 160 dB rejection that the die delivers. A board that ties the pad to a noisy plane gives away most of that rejection, and the symptom is a reading that moves when an unrelated channel switches.
The 100 V/V gain is the middle of the family and suits a shunt in the 0.25 to 1 milliohm range at 30 to 60 A. Below that current a 200 or 500 V/V member gives more output per ampere, and above it the 20 V/V member leaves headroom for a short circuit current. Our amplifier cross reference tabulates the single, dual and quad members by gain, and the power management cross reference note covers the companion gate drivers and regulators that usually sit on the same board.
Buyer questions on the INA4290A3IRGVR
Are the four channels isolated from each other? No. They share a supply and a ground, and only the input pairs are independent. A channel that measures a rail above the supply is fine because the common mode range is separate, but the outputs all sit inside the supply.
Can one channel be left unused? Yes, tie both inputs to a defined voltage and leave the output open. A floating input pair on an unused channel does not damage the part but adds noise to the shared supply.
Why is the bandwidth quoted at 20 V/V? Because the family quotes its widest figure at the lowest gain; at 100 V/V the bandwidth is lower and the vendor curves show the roll off, so a fast protection path at this gain should be checked against the curve rather than against the headline.
Availability and ordering notes
INA4290A3IRGVR is the quad channel 100 V/V member in the 4 mm QFN. It shares a document with the single and dual members, SBOS961C revised June 2021, so the electrical rows are common and only the package section differs. A quad order is usually a full reel, and the QFN's thermal pad means the board needs a paste stencil change from a four package solution, which should be accounted for in a first article rather than discovered at production.