INA4181A1IPWR
Product Specifications
INA4181A1IPWR
Texas Instruments — Power Management & Signal Chain
Product Overview
The INA4181A1IPWR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
INA4181A1IPWR: the gain of twenty member of the bidirectional four channel family
INA4181A1IPWR is the gain of twenty member of the bidirectional four channel current sense family, in the fourteen pin TSSOP on the large reel. The output sits at the reference voltage with no current and moves either side of it as the current changes direction, which is what makes the part usable on a charge and discharge path or an H bridge.
The reference is normally half the supply, so a 3.3 volt converter sees a 1.65 volt zero current point and about 1.6 volts of swing in each direction. The common mode window, the four gain options and the 900 microamp quiescent current are shared with the unidirectional family beside it, and the difference is entirely in the reference path.
INA4181A1IPWR as the vendor document publishes it
| Channels | 4 |
| Direction | bidirectional, output referred to the reference pin |
| Reference | normally half the supply |
| Gain options | 20, 50, 100 and 200 volts per volt, fixed by an internal network |
| Common mode range | 0.2 volts below ground to 26 volts |
| Supply | 2.7 to 5.5 volts |
| Offset at zero volts of common mode | plus or minus 25 microvolts typical, plus or minus 150 maximum |
| Offset at 12 volts of common mode | plus or minus 100 microvolts typical, plus or minus 500 maximum |
| Offset drift | 0.2 microvolts per degree typical, 1 maximum |
| Common mode rejection | 84 decibels minimum, 100 typical at a zero sense voltage |
| Power supply rejection | 80 microvolts per volt |
| Gain error | 0.1 per cent typical, 1 per cent maximum |
| Gain error drift | 20 parts per million per degree |
| Bandwidth | 350, 210, 150 and 105 kilohertz for the four gains |
| Slew rate | 2 volts per microsecond |
| Voltage noise | 40 nanovolts per root hertz |
| Quiescent current | 690 microamps typical, 900 maximum at 25 degrees, 1 milliamp over temperature |
| Temperature range | minus 40 to plus 125 degrees |
| Package | 14 pins, TSSOP body PW |
| Catalogue code | INA4181A1IPWR |
| Vendor status | active |
| Gain | 20 volts per volt |
| Carrier | large reel, R suffix |
| Package | 14 pins, TSSOP body PW |
Bidirectional sensing, and the reference pin that makes it work
INA4181A1IPWR is the bidirectional member of the four channel current sense family: the output sits at the reference voltage when the sense voltage is zero, and moves above or below it as current flows in one direction or the other. The reference pin is normally held at half the supply, which puts the zero current point in the middle of the converter range.
The common mode window is the same 0.2 volts below ground to 26 volts, the supply is 2.7 to 5.5 volts, and the four gain options are 20, 50, 100 and 200 volts per volt. The difference from the unidirectional part is not the amplifier but the reference path, and the reference path is what doubles the usable output swing for a given supply.
The offset table read with a mid supply reference
The offset of INA4181A1IPWR is plus or minus 25 microvolts typical and plus or minus 150 microvolts maximum at a common mode of zero volts, and plus or minus 100 microvolts typical with plus or minus 500 microvolts maximum at 12 volts. The drift is 0.2 microvolts per degree typical and 1 microvolt per degree maximum.
With the reference at half supply, the offset appears twice in the transfer function: once as the input offset and once as the error of the reference divider, so the divider tolerance belongs in the same budget. A 1 per cent divider on a 3.3 volt rail is 16.5 millivolts of output shift, which is far larger than the 150 microvolt input offset and is the first thing to fix on a bidirectional channel.
Three hundred and fifty kilohertz, and the gain that takes it away
The four gain options of INA4181A1IPWR carry four bandwidths: 350 kilohertz at 20 volts per volt, 210 at 50, 150 at 100 and 105 at 200, all at a 10 millivolt sense voltage into a 10 picofarad load. The slew rate is 2 volts per microsecond and the voltage noise density is 40 nanovolts per root hertz.
A bidirectional channel on a motor phase sees a current that reverses at the switching frequency, so the small signal bandwidth and the slew rate both matter, and the 200 volts per volt option is the one that gives up the most of both. A 20 kilohertz loop with a 100 millivolt sense signal is comfortable at any of the four gains; a 100 kilohertz loop wants the 20 or 50 option.
Eighty four decibels over the whole common mode window
The common mode rejection of INA4181A1IPWR is 84 decibels minimum and 100 decibels typical, specified from zero to 26 volts of common mode with a zero sense voltage, across the full minus 40 to plus 125 degree range. The power supply rejection is 80 microvolts per volt, and the input bias current is quoted separately for the zero and 12 volt cases.
Eighty four decibels at 26 volts of common mode is 1.6 millivolts of input referred error if the rejection were flat, and the specification is written at the extremes precisely because a bidirectional channel spends its life moving between them. That is the row that decides whether a low side shunt can be replaced by a high side one without losing accuracy.
Six hundred and ninety microamps, and the four channel package
The quiescent current of INA4181A1IPWR is 690 microamps typical and 900 microamps maximum at 25 degrees for all four channels, rising to 1 milliamp maximum over the temperature range. The package is the fourteen pin TSSOP, the same body as the unidirectional quad beside it, and the reel code carries the R suffix.
Four channels at 900 microamps is 225 microamps per channel, which is a quarter of what four separate single channel parts would draw including their own references. That is the reason the quad exists at all in a battery powered instrument, and it is also why the reference divider is normally shared across the four channels rather than built four times.
Where a bidirectional four channel part changes the bill of materials
INA4181A1IPWR belongs in a battery charge and discharge path, where the same shunt carries current both ways; in an H bridge or a solenoid driver, where the direction reverses on every cycle; in a bidirectional converter, where the current sign decides the mode; and in a servo amplifier that regenerates into its supply.
What changes in the bill of materials is the reference: a bidirectional quad needs one stable reference for four channels, and the divider that produces it has to be better than the offset budget or the whole exercise is wasted. The alternative, four unidirectional channels with a level shift each, costs more parts and four more error terms, which is the trade this family exists to avoid.
What the reference pin costs in practice
A reference pin turns a single ended output into a differential one, and the price is that the reference has to be as quiet as the amplifier. A divider from the supply with a 100 nanofarad capacitor is enough for a 1 per cent measurement and is not enough for a 0.1 per cent one, because the supply ripple passes through the divider at its full amplitude.
The second cost is the output swing. With the reference at half supply, each direction gets about 1.6 volts on a 3.3 volt rail instead of 3.2, so a gain that was chosen for a unidirectional channel has to be doubled for the same shunt and the same full scale current. That is the arithmetic to do before the bill of materials is fixed.
The reference divider is the part of a bidirectional channel that is most often under specified. Our amplifier cross reference page covers the gain options, and the BOM scrubbing page covers the divider against the bill of materials.
What reference voltage should be used? Half the converter supply is the usual choice, because it gives equal swing in both directions. A 1.65 volt reference on a 3.3 volt rail leaves 1.6 volts each way after the output swing limits are counted.
Does the gain of twenty suit a bidirectional rail? Yes, where the shunt is 10 milliohms and the current is a few amps. The gain only changes the output span, not the direction handling.