Contact Us

INA333AIDRGR

Brand: Texas Instruments
Texas Instruments INA333AIDRGR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA333AIDRGR — Power Management & Signal Chain | Superb Automation

INA333AIDRGR

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA333AIDRGR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA333AIDRGR: 50 uA zero drift instrumentation amplifier with a 100 kOhm gain term in the eight pin SON

INA333AIDRGR is a micro power instrumentation amplifier that sets any gain from 1 to 1000 with one external resistor in a SON body of 8 pins. It runs from 1.8 V to 5.5 V, draws 50 uA of quiescent current, and uses a chopper stabilised three amplifier topology that holds a 25 uV offset limit and 0.1 uV per degree of drift once the gain reaches 100. The gain term is 100 kOhm, so gain is 1 plus 100 kOhm divided by RG, and the inputs are filtered against radio frequency interference as part of the silicon rather than by external parts.

Order code and package

INA333AIDRGRSON DRG body, 8 pins, 3000 pieces on a large reel, Active in the addendum dated 10 November 2025, NIPDAU finish, moisture level 2 with a one year floor life, marking I333A, minus 40 to plus 125 degrees
INA333AIDRGTthe same DRG body on a 250 piece small reel at the same moisture level, which is the prototype and repair quantity
INA333AIDGKRVSSOP DGK body, 8 pins, 2500 pieces on a large reel, marking I333, which is the body to use when the board has room for a leaded package and a 2500 piece reel suits the run
INA333AIDGKTthe same DGK body on a 250 piece small reel, marking I333A
INA333AIDRGRG4the G4 row of the same DRG body and the same 3000 piece reel, printed separately in the addendum with its own finish column, which is the row a material declaration usually quotes

Electrical parameters that decide the application

Gain equation1 plus 100 kOhm divided by RG, any gain from 1 to 1000, with the internal resistors trimmed as a ratio rather than as absolute values
Supply1.8 V to 5.5 V single rail or plus or minus 0.9 V to plus or minus 2.75 V split, 50 uA quiescent current typical
Offset voltage25 uV maximum at a gain of 100 and above, which is the condition the headline figure carries and the one that is often dropped when the number is quoted
Offset drift0.1 uV per degree at a gain of 100 and above, from the auto zero stage rather than from trimming
Input bias current200 pA maximum, which is the figure that lets a high impedance bridge or a pH electrode connect without a buffer
Common mode rejection100 dB minimum at a gain of 10 and above, quoted across the input window of 0.1 V inside each rail
Input rangefrom 0.1 V above the negative rail to 0.1 V below the positive rail, so a 3.3 V single supply gives 0.1 V to 3.2 V of common mode
Output rangefrom 0.05 V above the negative rail to 0.05 V below the positive rail, which is a rail to rail output stage inside 50 mV
Noise50 nV per root hertz at a gain of 100 and above, with the chopper keeping the low frequency corner out of the audio band
Bandwidthquoted per gain in the electrical table and falling with gain, in the tens of kilohertz at a gain of 100
Radio frequency rejectioninput filters built into the silicon, which is why the part appears in instruments that sit next to a transmitter
Temperatureminus 40 to plus 125 degrees, with the offset and drift limits specified over that whole range rather than at 25 degrees

Family variants and how they differ

INA333 against INA128the INA128 uses a 50 kOhm gain term, so the same resistor value gives twice the gain here, and the INA333 runs at 50 uA against the 700 uA of the older part, which is the trade that made the family popular in portable instruments
INA333 against INA821the INA821 is a wider bandwidth part with a 49.4 kOhm term and 600 uA of current, useful where a gain of 100 has to hold 290 kHz, and the INA333 is the part for a 50 uA budget
INA333 against INA186the INA186 is a current shunt monitor with a fixed gain and a 40 V common mode window, while this is a true differential amplifier with a resistor set gain and a common mode that has to stay inside the supply, so the two solve different problems
Single against dualthe INA2332 is the dual member of the same architecture, which matters for a two channel instrument that would otherwise need two packages and two sets of bypass capacitors
Body optionsthe DGK and DRG bodies are the same silicon, so the choice is reel size and board space rather than electrical grade

Points to check before this part goes on a BOM

The 25 uV offset and the 0.1 uV per degree drift are quoted at a gain of 100 and above, and that condition changes the part completely at low gain. The output stage offset appears at the output divided by nothing, so at unity gain the input referred offset is the input stage offset plus the output stage offset, and the datasheet quotes the total error curve rather than the headline. An instrument that needs 25 uV at unity gain needs a different part or a gain stage in front.

The 100 kOhm gain term is twice the 50 kOhm of the INA128, so a resistor chosen for a gain of 100 on the older part gives a gain of 200 here. That is a factor of two error that survives every bench check because the amplifier is working correctly; it is the resistor, or rather the assumption behind it, that is wrong. Anyone replacing an INA128 with this part has to change RG, and the pinout is the same which makes the mistake easy to make.

The input window is 0.1 V inside each rail, and on a 3.3 V single supply that is 0.1 V to 3.2 V. A bridge sitting at mid supply is comfortable. A thermocouple referenced to ground is not, because its cold junction sits at 0 V and the amplifier cannot see it, so either the supply goes negative or the thermocouple is lifted onto a reference. This is the single most common reason a part like this appears not to work on a bench.

The 50 uA quiescent current is the whole amplifier including the chopper, and the chopper is what delivers the drift figure. What the chopper also does is inject charge at the input at its switching frequency, and a source impedance above about 10 kOhm converts that charge into a voltage. The datasheet specifies the input filter and asks for a capacitor across the inputs, and a circuit that omits it sees a few microvolts of offset that moves with source resistance.

The radio frequency filters on the inputs are part of the silicon and they are the reason this part is specified for instruments near transmitters. They do not replace a common mode choke on a cable that carries an ESD strike, and they do not protect the inputs beyond the absolute maximum ratings, so a transducer on a long lead still needs external protection. What they do remove is the rectification of a few hundred millivolts of radio frequency that would otherwise appear as a DC offset.

The two bodies differ in reel size and in nothing electrical. The DRG body is the smaller of the two at 3 mm by 3 mm and ships 3000 to a reel, the DGK body ships 2500, and both carry moisture level 2 with a one year floor life, so neither needs a dry pack schedule beyond the standard one. A line that runs out mid build and substitutes one body for the other does not need an engineering change, only a footprint check.

Choosing RG and what it costs in error

A gain of 10 needs 11.1 kOhm, a gain of 100 needs 1.01 kOhm and a gain of 1000 needs 100.1 Ohm. The internal 100 kOhm is trimmed to a ratio, so the gain error is dominated by the external resistor: a 1 per cent resistor gives 1 per cent of gain error and a 25 ppm per degree resistor adds 25 ppm per degree of drift, which is four times the amplifier's own 0.1 uV per degree once it is referred to the input.

The gain bandwidth product of the stage is about 350 kHz, so a gain of 100 leaves roughly 3.5 kHz of small signal bandwidth. That is enough for a weigh scale and not enough for an audio path, and the datasheet curves show the same thing. Choosing the gain before checking the bandwidth is how a 50 uA part ends up in a circuit that needed a 600 uA part.

Wiring the reference pin

The reference pin sets the output level for zero differential input and it is a high impedance node that should be driven from a low impedance source, usually a divider with a buffer or a reference IC. Leaving it floating is not an option, and tying it to ground on a single supply puts the output at the negative rail with zero input, which clips the negative half of a bipolar signal. On a 3.3 V single supply the usual choice is mid supply, which gives plus or minus 1.6 V of output swing.

Where this order code fits

Bridge amplifiers, ECG front ends, pressure sensors, medical instrumentation, weigh scales, thermocouple and RTD amplifiers and portable data acquisition are the applications the vendor names, and all of them present a small differential signal on a common mode that has to be arranged deliberately inside a single supply window. Teams comparing it with a neighbouring part start from our Amplifier Cross Reference page, and teams replacing a part that has gone end of life start from the Medical Device Components page.

Questions buyers ask

Is the 25 uV offset available at unity gain? No. The 25 uV limit is stated for gains of 100 and above, and at unity gain the output stage offset adds directly so the total is larger.

Can it replace an INA128 without changing anything? No. The gain term is 100 kOhm against 50 kOhm, so the same resistor gives twice the gain even though the pinout matches.

Does it work on a 1.8 V supply? Yes, 1.8 V is the minimum, and the input window then runs from 0.1 V to 1.7 V, which rules out any signal referenced to ground.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Pin to Pin Cross Reference page sets out the checks that keep a substitute from failing on the bench.