Contact Us

INA326EA-2K5

Brand: Texas Instruments
Texas Instruments INA326EA-2K5 is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA326EA-2K5 — Power Management & Signal Chain | Superb Automation

INA326EA-2K5

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA326EA-2K5 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA326EA-2K5: the precision instrumentation amplifier on a 2500 piece reel

INA326EA-2K5 is the precision instrumentation amplifier in the 8 pin MSOP on a 2500 piece large reel: 100 microvolts maximum of offset, 0.4 microvolts per degree of maximum drift, 100 dB minimum of rejection, a true rail to rail input that reaches 100 millivolts past the positive rail, and a gain of twice the external resistor ratio from below 0.1 to above 10 000.

It is a different class of part from the micropower family beside it in the catalogue, and the supply current says so: 1.6 milliamps typical and 3.4 maximum, forty times the 40 microamps of the INA321, spent on the auto-correction loop that holds the offset and removes the low frequency noise. The specified temperature range ends at plus 85 degrees, with operation to 125 but no guarantee.

INA326EA-2K5 as the vendor document publishes it

Offset voltage20 microvolts typical, 100 microvolts maximum
Offset drift0.1 microvolts per degree typical, 0.4 maximum
Input bias current0.2 nanoamps typical, 2 nanoamps maximum
Common mode rejection100 dB minimum, 114 dB typical
Voltage noise density33 nanovolts per root hertz at 10 Hz, 100 Hz and 1 kHz
Gain equation2 multiplied by the ratio of the two external resistors
Gain rangebelow 0.1 to above 10 000
Gain error at 10 and 1000.08 per cent typical, 0.2 per cent maximum
Gain drift6 ppm per degree typical, 25 maximum
Nonlinearity0.004 per cent of full scale
Quiescent current1.6 milliamps typical, 2.4 typical at 5 volts, 3.4 maximum
Supply range2.7 volts to 5.5 volts
Common mode range20 millivolts below the negative rail to 100 millivolts above the positive rail
Output swing from the rail5 millivolts typical, 10 millivolts maximum into 100 kohm
Bandwidthset by the external filter, 1 kHz corner in the specified condition
Slew rate0.95 volts per microsecond at 1 kHz, 1.3 at 10 kHz
Settling to 0.01 per cent130 microseconds at 1 kHz, 30 at 10 kHz
Overload recovery5 microseconds from a 50 per cent output overload
BodyMSOP, 8 pin, DGK, 3.00 by 3.00 millimetres
Temperature rangeminus 40 to plus 85 degrees specified, operation to 125
Vendor statusactive, 2500 piece large reel
Catalogue codeINA326EA-2K5
Vendor stringINA326EA/2K5, printed with a slash
MarkingB26
Moisture levellevel 2, 260 degrees, one year floor life
Temperature notespecified minus 40 to plus 85 degrees, operation to 125

The gain is twice the resistor ratio

The gain of INA326EA-2K5 is 2 multiplied by the ratio of the two external resistors, so a 1 to 1 pair gives unity and a ratio of 5000 gives a gain of 10 000. The range is specified from below 0.1 to above 10 000, which means the part can attenuate as well as amplify, and the attenuation is useful in front of a converter whose input range is wider than the sensor signal but whose reference would otherwise be divided.

Gain error at 10 and at 100 is 0.08 per cent typical and 0.2 per cent maximum, with 6 ppm per degree of typical drift and 0.004 per cent of nonlinearity. Those rows are the internal network only: the external resistors add their own tolerance and their own temperature coefficient directly, so a 0.1 per cent pair of 25 ppm resistors turns the channel into a 0.1 per cent channel with 25 ppm of gain drift. A precision channel needs a resistor network, not two discrete parts, and the network cost is usually larger than the amplifier cost.

One hundred microvolts maximum, four tenths of a microvolt of drift

The offset of INA326EA-2K5 is 20 microvolts typical and 100 microvolts maximum, with a drift of 0.1 microvolts per degree typical and 0.4 maximum over the industrial range. Against a 10 millivolt load cell signal the maximum offset is 1 per cent of full scale, which is why the part is normally paired with a production calibration step rather than used raw.

What the part buys is the stability of that offset rather than its size. Four tenths of a microvolt per degree over 125 degrees is 50 microvolts of movement, and the long term stability is specified separately because it is what a weigh scale is judged on over a year. A channel that calibrates once at room temperature and runs from 0 to 40 degrees sees 16 microvolts of drift, a fifth of the maximum offset, and that ratio is the reason the family is used in instruments that are calibrated once and then trusted.

Filter limited bandwidth and a correction loop that runs in the background

The bandwidth of INA326EA-2K5 is set by the external filter, 1 kHz in the specified condition, with a slew rate of 0.95 volts per microsecond at that corner and 1.3 at 10 kHz. Settling to 0.01 per cent is 130 microseconds at 1 kHz and 30 microseconds at 10 kHz, and overload recovery from a 50 per cent overdrive is 5 microseconds, which is what a multiplexed channel needs when it moves from a saturated sensor to a live one.

The part carries an internal oscillator that runs an auto-correction loop, so the offset and the 1/f noise are corrected continuously rather than only at power up. That is why the low frequency noise is specified as 0.8 microvolts peak to peak from 0.01 to 10 Hz and 33 nanovolts per root hertz above 10 Hz: the correction removes the drift and the flicker noise that a chopper would remove, without the switching artefacts that a chopper puts into the signal band. The cost is the quiescent current, which is where the next row begins.

Rail to rail in, one hundred millivolts past the positive rail

The input common mode range of INA326EA-2K5 runs from 20 millivolts below the negative rail to 100 millivolts above the positive rail, so a ground referenced thermocouple and a supply referenced bridge are both inside the window without a charge pump. The output swings to within 5 millivolts typical and 10 millivolts maximum of either rail into 100 kilo-ohms, which on a 4.096 volt reference is 2 or 3 codes at each end.

True rail to rail input is the row that separates this part from the older instrumentation amplifiers, which lose their input stage near either rail and change their offset when they do. The specification holds across the whole window rather than only in the middle, and the 100 millivolt overrange at the top means a sensor that sits at the supply rail does not push the channel out of range. What the window does not include is a negative input below 20 millivolts: a sensor that swings below ground needs a bias network or a bipolar supply.

One point six milliamps against forty microamps

INA326EA-2K5 draws 1.6 milliamps typical and 3.4 milliamps maximum, against 40 microamps for a micropower instrumentation amplifier of the same footprint. The fortyfold difference is the price of the auto-correction loop and the tighter offset: a chopper or a correction loop runs an oscillator and a second signal path, and both draw current continuously.

The choice between the two is not a preference. A 4 to 20 milliamp loop transmitter has about 3 milliamps for the whole circuit and cannot carry this part at all. A mains powered weigh scale has amps to spare and cannot tolerate the millivolt offset of the micropower part. Between those two there is a band of battery instruments that sample slowly and need 0.1 per cent, and that band is where the supply current has to be budgeted against the drift over the battery life rather than against the data sheet.

Where a precision instrumentation amplifier fits

INA326EA-2K5 fits a load cell or a strain gauge channel, a thermocouple front end with a cold junction, a pressure transducer in a process instrument, and a medical or laboratory channel that has to hold its calibration over a year. The 100 microvolt maximum offset, the 0.4 microvolt per degree drift, the rail to rail input and the 0.004 per cent nonlinearity are the four rows those channels are bought on.

It stops at three things. The supply current rules out a loop powered transmitter and most coin cell instruments. The specified temperature range ends at plus 85 degrees, with operation to 125 but no guarantee, so a channel that runs hot needs a different part. And the bandwidth is filter limited, so an acoustic or a vibration channel belongs elsewhere. Our amplifier cross reference page covers the instrumentation amplifiers that trade one of those three for the offset, and the obsolete part cross reference hub covers the older codes in the same family.

A load cell channel is bought on the offset, the drift and the long term stability rather than on the supply current. Our amplifier cross reference page covers the instrumentation amplifiers either side of this one, and the obsolete part cross reference hub covers the older codes in the family.

What gain does a 2 kilo-ohm and 100 kilo-ohm pair give? A ratio of 50 and a gain of 100, from twice the ratio.

Is this part usable on a 4 to 20 milliamp loop? No. The loop has about 3 milliamps for the whole circuit and this part alone draws up to 3.4.