Contact Us

INA310A2IDGKR

Brand: Texas Instruments
Texas Instruments INA310A2IDGKR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA310A2IDGKR — Power Management & Signal Chain | Superb Automation

INA310A2IDGKR

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA310A2IDGKR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA310A2IDGKR: 50 V/V current sense with a comparator for a 48 V rail

The INA310A2IDGKR is the 50 V/V, A grade member of the INA310x family. It shares the die, the body and the pinout with the rest of the family and differs in the gain that is fixed at the factory, which sets the shunt value for a given full scale current. At 50 V/V a 1 milliohm shunt delivers 50 mV per 1 A, so 3 V at the output is reached at 60 A, and a 20 A working current sits at 1 V, which is a comfortable place for a 12 bit converter.

The part measures with a common mode range of 4 V to 110 V, including 4 V below ground, and it does so independently of its own supply, which runs from 2.7 V to 20 V at 1.6 mA. The comparator beside the amplifier has an open drain output, a 0.6 V internal reference and a latching mode, so the same part can report current to a converter and assert a fault line without a second package.

Key data for the INA310A2IDGKR

Gain50 V/V on the A2 code, which is the middle setting of the five the family offers
Common modeMinus 4 V to 110 V operational, minus 20 V to 120 V survival, independent of the supply
AccuracyGain error 0.15 per cent maximum with 10 ppm per degree drift, offset 20 uV maximum with 0.25 uV per degree drift on the A grade
ComparatorOpen drain, 0.6 V internal reference, 1 microsecond typical propagation delay, latching released by RESET, hysteresis in the 50 mV class
Speed1.3 MHz bandwidth and 2.5 V per microsecond slew rate, 160 dB typical DC common mode rejection
Supply2.7 V to 20 V single rail, 1.6 mA quiescent, minus 40 C to 125 C operating range

Body, marking and reel data

BodyDGK, 8 pin VSSOP at 3.00 mm by 3.00 mm, the only body the family is published in
ReelR suffix is the large reel; the 3 mm body keeps the divider resistors close to the comparator pin, which is what the trip accuracy depends on
PinsSeparate CMPIN, CMPOUT and RESET pins, so the comparator can be left unused by tying CMPIN to ground and leaving CMPOUT open
Supply pinVS is separate from the measured rail, which is how a 5 V control supply watches a 48 V bus
FamilyFive gains share one document and one body, so a gain change is a reorder and not a board change

Where 50 V/V fits on a 48 V rail

Fifty is the gain that matches a 1 milliohm shunt to a 60 A full scale, and 60 A is a common rating for a 48 V rectifier branch or a server busbar feed. The same 1 milliohm shunt at 20 V/V would need 150 A to reach full scale, which leaves the working range compressed into the bottom of the converter; at 100 V/V it would saturate at 30 A, which is too close to a 25 A working current for comfort. The middle gain is not a compromise here, it is the setting that puts the working range in the upper half of the converter.

The comparator is the part that has to be sized with care. Its input is the amplifier output through a divider, so the trip point inherits the amplifier gain error and adds the divider tolerance and the comparator offset. A trip at 30 A with a 1 per cent divider and a 0.15 per cent amplifier is a trip that moves by about 0.35 A, which is fine for a protection threshold and not fine for a control loop limit. Where a board uses the comparator as a fast protection and the amplifier output as the control signal, the two paths have to be checked separately. Our amplifier cross reference shows which members carry a comparator and which do not, and the pin to pin cross reference note covers the pin function order that lets one board accept either version.

Buyer questions on the INA310A2IDGKR

Can the comparator drive a relay directly? No. It is an open drain output with a limited sink current, so it drives a logic input or a small LED through a resistor; a relay needs a transistor or a driver.

What sets the hysteresis? The comparator has a fixed hysteresis in the 50 mV class at its input, which at 50 V/V is 1 mV of shunt signal, or 1 A on a 1 milliohm shunt. That is the smallest step the trip point can resolve without chatter.

Does the RESET pin need a pull up? Yes, because it is an input that releases the latch when driven low; leaving it floating is not a defined state, so tie it to the supply through a resistor or drive it from a controller pin.

Availability and ordering notes

INA310A2IDGKR is the A grade 50 V/V member in the 8 pin VSSOP. The Q1 automotive grade is published separately as INA310A2QDGKRQ1 and carries its own document, so the two codes should not be mixed on one quotation without naming which grade the line item is. Because the family shares one body, a customer who changes gain between prototypes and production does not need a new footprint, only a new order code.