INA296A3IDDFR
Product Specifications
INA296A3IDDFR
Texas Instruments — Power Management & Signal Chain
Product Overview
The INA296A3IDDFR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
INA296A3IDDFR: bidirectional 50 V/V current sense with 0.01 per cent gain error
The INA296A3IDDFR is the A grade, 50 V/V member of the INA296x family, a bidirectional current sense amplifier that measures a shunt drop with a common mode range of 5 V below ground to 110 V above it. The A grade is the tight one: gain error is 0.01 per cent maximum with 1 ppm per degree drift, and offset is 10 uV maximum with 0.1 uV per degree drift. At 50 V/V a 1 milliohm shunt carrying 20 A gives 20 mV in and 1 V out, so the full scale of a 3 V converter is reached at 60 A, which leaves the whole working range inside the linear window.
Bidirectional operation matters when the same shunt carries charge and discharge, or when a motor regenerates into its supply. The output swings on either side of the reference pin, and the two reference pins let the zero point be placed at mid rail or at ground depending on whether the host converter is single ended or differential. Bandwidth is 1.1 MHz at every gain in the family, with an 8 V per microsecond slew rate and a 1 microsecond settling time to 1 per cent, so the same part serves both the protection comparator and the control loop.
Key data for the INA296A3IDDFR
| Gain | 50 V/V on the A3 code; 10, 20, 100 and 200 V/V are the other four members |
| Common mode | Minus 5 V to 110 V operational, minus 20 V to 120 V survival, independent of the supply rail |
| Gain accuracy | 0.01 per cent maximum on the A grade with 1 ppm per degree drift, against 0.1 per cent and 5 ppm on the B grade |
| Offset | 10 uV maximum on the A grade with 0.1 uV per degree drift, against 150 uV and 0.5 uV per degree on the B grade |
| Rejection and speed | 166 dB typical DC common mode rejection, 1.1 MHz bandwidth at all gains, 8 V per microsecond slew rate |
| Supply | 2.7 V to 20 V single rail, 2.5 mA quiescent, minus 40 C to 125 C |
Body, marking and reel data
| Body | DDF, 8 pin SOT-23 at 2.9 mm by 2.8 mm, one of three bodies the family ships in |
| Siblings | The same die is offered in DGK VSSOP-8 at 3 mm by 4.9 mm and in D SOIC-8 at 4.9 mm by 6 mm, all with the same pin function order |
| Reel | R suffix is the large reel; the DDF body is the one to name when the board has a 3 mm wide keep out |
| Pins | Two reference pins, REF1 and REF2, plus OUT, VS, GND, IN plus and IN minus; the eighth pin is a no connect on the DDF body |
| Grade | A and B grades share the body and the pinout and differ only in the accuracy rows of the electrical table |
Where the 50 V/V member fits
Fifty is the middle gain, and it is the one that suits a 48 V telecom or server rail where the working current is between 5 A and 40 A. With a 0.5 milliohm shunt the full scale output of 3 V arrives at 120 A, which is far beyond the working current, so the resolution at 5 A is poor; with a 2 milliohm shunt full scale arrives at 30 A, which puts the working range in the top half of the converter and keeps 30 mA of resolution on a 12 bit host. Choosing the shunt against the gain is the whole exercise, and the amplifier itself is the part that does not change.
The A grade is worth its price when the reading is used for billing, for a current limit that must not drift with temperature, or for a battery model that integrates charge over years. Its 10 uV maximum offset over the full temperature range is the number that keeps a 20 A reading honest at minus 40 C, where a B grade part with 150 uV of offset would move by 7.5 mA on a 2 milliohm shunt for offset alone. Where a board is being moved from an older single direction amplifier, our amplifier cross reference groups candidates by gain and direction, and the one stop BOM sourcing note covers how a mixed order of A and B grades is consolidated on one shipment.
Buyer questions on the INA296A3IDDFR
Does the two pin reference allow a true zero at ground? Yes. Tying both reference pins to ground puts the zero at ground and the output only swings positive, which is the single ended case; separating them lets the zero sit at a mid rail voltage for a differential converter.
Why is the bandwidth the same at every gain? Because the gain is set inside the amplifier and the compensation follows it, so a 200 V/V member does not lose bandwidth against the 10 V/V member. That is unusual in this class and it is the reason the family can be used for fast overcurrent detection at any gain.
Is a 110 V common mode rating enough for a 96 V battery pack? At full charge a 96 V pack sits above the rating, and the survival row is only 10 V higher than the operational row, so a pack that can reach 110 V needs a divider or a different part rather than a margin argument.
Availability and ordering notes
INA296A3IDDFR is the A grade 50 V/V member in the 8 pin SOT-23. The addendum rows in the library document cover DDF, DGK and D bodies, and the A and B grades are printed as separate order codes, so a purchase order that names only the family will not fix the grade. Where a customer asks for the B grade as a cost reduction, the pinout is unchanged and the board does not need a change, but the offset and gain rows move by an order of magnitude and the accuracy claim in the end product has to be checked against that.