INA293A4QDBVRQ1
Product Specifications
INA293A4QDBVRQ1
Texas Instruments — Power Management & Signal Chain
Product Overview
The INA293A4QDBVRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
INA293A4QDBVRQ1: a 200 V/V current sense amplifier that works above and below ground
The INA293A4QDBVRQ1 is the A4 gain member of the INA293 family, a current sense amplifier that measures the drop across a shunt resistor with a common mode range of 4 V to 110 V and a negative side that reaches 4 V below ground. The A4 suffix fixes the gain at 200 V/V, which is the setting for a small shunt signal: a 1 milliohm shunt carrying 15 A develops 15 mV, and 200 V/V turns that into 3 V at the output, which is a full scale reading on a 3.3 V converter.
The part runs from a single 2.7 V to 20 V supply and draws 1.5 mA, so it can sit on the same 12 V housekeeping rail as the converter it is watching. Bandwidth is 1.3 MHz with a 2.5 V per microsecond slew rate, which is what puts this family in overcurrent protection rather than in slow telemetry only: a comparator behind the output can catch a fault in a fraction of a microsecond instead of waiting for a sampled conversion.
Key data for the INA293A4QDBVRQ1
| Gain | 200 V/V fixed by the A4 order code; the family also offers 20, 50, 100 and 500 V/V in the same body |
| Common mode | Operational range minus 4 V to plus 110 V, survival minus 20 V to plus 120 V, so a 48 V rail and a half bridge recirculation event both sit inside the window |
| Accuracy | Gain error 0.15 per cent maximum with 10 ppm per degree drift, offset 15 uV typical with 0.05 uV per degree typical drift |
| Rejection | 160 dB DC common mode rejection and 85 dB at 50 kHz, which is the figure that decides how much switching noise reaches the output |
| Speed | 1.3 MHz small signal bandwidth, 2.5 V per microsecond slew rate |
| Supply | 2.7 V to 20 V single rail, 1.5 mA quiescent, minus 40 C to 125 C operating range |
Body, marking and reel data
| Body | DBV, 5 pin SOT-23 at 2.90 mm by 1.60 mm, the smaller of the two pinouts the family ships in |
| Grade | Q1 automotive suffix; the library document SBOS470B is the industrial revision of this part, so the automotive qualification rows come from the separate Q1 document |
| Reel | R suffix is the large reel; the 5 pin SOT-23 body is the one that keeps a shunt amplifier inside a 3 mm by 3 mm keep out on a dense board |
| Pinout | Two pinout variants exist in the family, so a second source check has to compare pin numbers and not only the body size |
| Temperature | Specified from minus 40 C to 125 C on the industrial document; the automotive grade carries its own ambient and junction limits |
Where a 200 V/V current sense amplifier earns its place
At 200 V/V the input window is narrow by intent. A 3 V output swing is reached with 15 mV across the shunt, so the sense resistor can be small enough to keep its own loss below a fraction of a watt at 20 A. The trade is that the offset becomes the accuracy floor: 15 uV typical at the input is 0.1 per cent of 15 mV, and the same offset on a 5 mV signal is 0.3 per cent. That is why the A4 member is chosen for a rail where the working current is well above the bottom of the range, and a lower gain member is chosen when the load spends most of its life at a few hundred milliamps.
The negative common mode is the second reason this part turns up in motor and half bridge work. When a low side switch recirculates, the shunt sits below ground for the duration of the dead time, and an amplifier that stops at zero either clips or changes its offset on the way back. The INA293 stays linear through that excursion, which keeps the current waveform usable for a fault decision rather than only for a display. Where a board is moving between this part and a pin compatible alternative, our amplifier cross reference lists the members by gain, common mode and output type, and the pin to pin cross reference note covers the two SOT-23 pinouts that share the same footprint but not the same pin numbers.
Buyer questions on the INA293A4QDBVRQ1
Can the output drive a 3.3 V converter directly? Yes, within the output swing that the supply allows, and the output is a voltage, so a series resistor into a converter input is the only part needed. Keep the load capacitance small, because a 1.3 MHz amplifier with a heavy capacitive load will ring.
Is 20 V the largest supply this part accepts? It is the largest recommended supply, while the common mode input reaches 110 V independently. The supply and the measured rail are separate pins, which is what lets a 5 V control rail watch a 48 V bus.
What happens if the shunt opens? The input current is limited by the internal resistor network, but the reading becomes meaningless; a differential input that floats to the bus voltage is not a fault the amplifier can report. Add a comparator on the output if an open shunt has to be detected.
Availability and ordering notes
INA293A4QDBVRQ1 is the automotive grade 200 V/V member in the 5 pin SOT-23. The industrial document in our library, SBOS470B revised August 2022, prints the A and B grades with the five gain options but no Q1 rows, so the automotive temperature grade, the PPAP level and the reel size should be confirmed against the Q1 qualification document before a purchase order is released. Where a customer is second sourcing this position, the gain letter and the pinout variant both have to match, since a different gain in the same body reads the same current at a different scale factor.