INA290A5IDCKR
Product Specifications
INA290A5IDCKR
Texas Instruments — Power Management & Signal Chain
Product Overview
The INA290A5IDCKR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
INA290A5IDCKR: 500 V/V on 120 V, and a status problem worth knowing
The INA290A5IDCKR is the 500 V/V member of the INA290 family, a bidirectional current sense amplifier that works from 2.7 V to 120 V of common mode with a survival range of minus 20 V to 122 V. Offset is 12 uV maximum with 0.2 uV per degree of drift, gain error is 0.1 percent maximum, DC common mode rejection is 160 dB typical and the AC figure is 85 dB at 50 kHz. It runs from a 2.7 V to 20 V supply and draws 370 uA per channel, in a 5 pin SC70 body.
The status is the first thing a buyer should see. In the current addendum the plain INA290A5IDCKR row is printed Obsolete, while the .B row of the same string is active with the finish column reading Call TI and no quantity, and INA290A5IDCKT is active at 3000 pieces on a large reel with marking 1FU. A build that still calls the R suffix on a purchase order is calling a row the vendor has already retired, and the substitute is not automatic because the packing differs.
Key data for the INA290A5IDCKR
| Gain | 500 V/V fixed, the highest of five options from 20 to 500 V/V in the family |
| Common mode | 2.7 V to 120 V operational, minus 20 V to 122 V survival, independent of the 2.7 V to 20 V supply |
| Accuracy | Offset 12 uV maximum, 0.2 uV per degree, gain error 0.1 percent maximum, gain drift 5 ppm per degree |
| Rejection | 160 dB DC typical, 85 dB at 50 kHz, with a negative common mode that keeps the input linear below ground |
| Speed | 1.1 MHz at gain 20 and gain dependent above it, 2 V per microsecond slew rate |
| Supply | 2.7 V to 20 V, 370 uA typical quiescent, minus 40 C to 125 C, 5 pin SC70 body |
Body, marking and reel data
| Body | DCK, 5 pin SC70, the smallest package in the family; the dual and quad versions use MSOP and QFN bodies |
| Reel | 3000 pieces on a large reel for the T row, which is the active packing for this gain |
| Finish | The T row prints a finish column that reads Call TI; the level and the plating have to be confirmed rather than read off the table |
| Marking | 1FU on the active A5 reel, against 1FT on the obsolete row, so the marking changed with the status |
| Family spread | Single channel in SC70, dual in MSOP, quad in a 4 mm by 4 mm QFN, all with the same front end |
Where 500 V/V and 120 V meet
Telecom rectifiers, power over ethernet feeds, industrial 48 V and 110 V DC buses, and battery management on high voltage packs are the natural users. A 500 V/V gain turns 10 mV of shunt drop into 5 V, so a 100 milliohm shunt measures down to a few milliamps while the common mode sits at 110 V. That combination is rare enough that the part has few direct competitors.
Two constraints follow. The output swing limits the input window to about 3 mV on a 3.3 V supply, so the shunt drop at full current has to be small and the shunt itself has to be sized for the low end rather than the high end. And at 120 V the part is at the edge of what a non isolated amplifier can do, so a 400 V bus needs an isolated modulator or a divider and a different approach. Where a board is moving from the R to the T suffix, the packing and the marking change but the die does not, and our obsolete part cross reference hub keeps the status history for the family so a customer's approved vendor list can be updated with evidence rather than a verbal note.
Buyer questions on the INA290A5IDCKR
Is the R suffix still orderable? The current addendum prints INA290A5IDCKR as Obsolete. The .B row of the same string is active but carries Call TI and no quantity, and the T row is active at 3000 pieces. Any order should be placed on a row that the vendor still publishes.
Does the marking differ between the rows? Yes, 1FT on the obsolete row and 1FU on the active one, which is a useful check at goods in when a distributor supplies older stock.
Is the 12 uV offset real at 500 V/V? It is a maximum, and it is referred to the input, so at the output it is 6 mV. On a 5 V full scale output that is a tenth of a percent, which is why the gain error row and the offset row are both quoted.
Availability and ordering notes
The status picture on this string is the reason the page exists in this form. INA290A5IDCKR is printed Obsolete, INA290A5IDCKR.B is active with Call TI and no published quantity, and INA290A5IDCKT is active at 3000 pieces on a large reel with marking 1FU. A customer moving a production line should plan on the T row or on a written vendor confirmation for the B row, not on the R row. Where the change lands mid programme, the end of life process is the one to follow, and the component obsolescence management note describes how we date the change, hold a buffer and document the replacement path.