INA241A5IDR
Product Specifications
INA241A5IDR
Texas Instruments — Power Management & Signal Chain
Product Overview
The INA241A5IDR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
INA241A5IDR: 200 V/V, 110 V common mode, 8 pin SOIC
The INA241A5IDR is the highest gain member of the INA241A family, 200 V/V, in the 8 pin SOIC body. Common mode is minus 5 V to 110 V with 120 V survival, offset is 10 uV maximum, gain error 0.01 percent maximum, and the small signal bandwidth stays at 1.1 MHz even at this gain. On a 3.3 V rail with the output biased at mid supply the usable swing is about 1.5 V, so the input window is 7.5 mV, which is 7.5 A through a 1 milliohm shunt or 750 mA through a 10 milliohm shunt.
That window is what makes a 200 V/V part a low current instrument rather than a phase current sensor. It is the right choice for a precharge resistor, a leakage path, a solenoid holding current or a battery pack that has to be watched while it sleeps, and the wrong choice for a traction inverter where the peak current is hundreds of amps. The SOIC body also gives the most copper area for the die, which matters when the amplifier sits in a hot enclosure and its own quiescent current is the only heat source it controls.
Key data for the INA241A5IDR
| Gain | 200 V/V fixed, the highest of the five options in this family |
| Common mode | Minus 5 V to 110 V operational, minus 20 V to 120 V survival, independent of the supply |
| Accuracy | Offset 10 uV maximum, 0.1 uV per degree, gain error 0.01 percent, gain drift 1 ppm per degree |
| Rejection | 166 dB DC typical, 104 dB at 100 kHz and 89 dB at 1 MHz, with rejection built for switching to 125 kHz |
| Speed | 1.1 MHz at all gains, 8 V per microsecond slew, 1 us settling to 1 percent of a step |
| Supply | 2.7 V to 20 V, 2.5 mA typical and 3 mA maximum quiescent, minus 40 C to 125 C |
Body, marking and reel data
| Body | D, 8 pin SOIC at 4.9 mm by 3.91 mm, the largest of the three bodies in the family |
| Reel | 2500 pieces on a large reel for the D rows, matching the quantity of the DGK rows |
| Finish | NIPDAU at moisture level 2, one year floor life |
| Marking | I241A5 on the SOIC, the only body in the family with room for the full gain code |
| Tier split | The B tier at the same gain carries 150 uV offset and 0.1 percent gain error, for comparators rather than measurement |
Where the highest gain is the right answer
A precharge circuit is the textbook case: the current through the resistor starts high and falls as the bus capacitor charges, and the interesting part of the curve is the last hundred milliamps where a contactor is about to close. A 200 V/V front end on a 10 milliohm shunt turns 100 mA into 200 mV, which is 20 times the offset floor, and the same part clips gracefully at 750 mA on the top of the range as long as the host software does not need that region.
Two cautions follow. The first is common mode: an amplifier rated to 110 V is fine on a 96 V pack and not fine on a 400 V pack, where a divider or an isolated amplifier is the correct answer. The second is noise. At 200 V/V the input referred noise of the front end is multiplied by 200, so a 1.1 MHz bandwidth that was clean at gain 10 now passes a wider noise band into the converter, and the output filter has to be sized for the gain actually used. Where a board is moving from a 50 V/V part to this one, our amplifier cross reference note lists the gain, swing and noise for each member, and the component lead time solutions note covers the substitutions that keep a build moving when one gain of the family is short.
Buyer questions on the INA241A5IDR
Can it measure microamps? With a 1 ohm shunt, 10 uA gives 2 mV at the input and 400 mV at the output, which is readable. With the offset of 10 uV, the floor is around 50 nA through that shunt, so the part is genuinely usable for leakage measurement.
Does the SOIC body have a different specification? No, the electrical table is common to all three bodies. Only the thermal resistance and the reel size differ.
Is the negative common mode range useful here? Yes on a solenoid, where the flyback drives the input below ground, and on any inductive load that is switched hard.
Availability and ordering notes
The D rows of this family are published at 2500 pieces on a large reel at moisture level 2, and the ordering table in this revision has the package and quantity columns shifted by a row, with one or two rows carrying a footnote marker instead of a value. The practical rule is the same for every gain: quote the part number plus the body plus the reel size, and confirm the whole string against the vendor record. The body marking on the SOIC does spell the gain, which makes the D body the easiest of the three to verify at goods in, and that check is written into the pin to pin cross reference record for this family.