INA240A3PW
Product Specifications
INA240A3PW
Texas Instruments — Power Management & Signal Chain
Product Overview
The INA240A3PW from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
INA240A3PW: the 100 V/V gain in the TSSOP, and the row the addendum closes
INA240A3PW is the 100 V/V option in the 8 pin TSSOP, and the addendum prints it Obsolete with 2500 pieces on a large reel and no active successor in the same body at that gain. The electrical rows are the family's: 132 dB of DC rejection, 93 dB at 50 kHz, 25 microvolts of maximum offset, 400 kHz of bandwidth and 1.8 milliamps typical of quiescent current.
The active row at this gain is INA240A3PWR, which the same addendum prints with a dash in the quantity column and a call for the lead finish. A line that has INA240A3PW released on the bill of materials has to move to the R suffix or to the SOIC body, and the move is a carrier change rather than an electrical one, so the gain, the footprint and the scaling constant stay as they are.
INA240A3PW as the vendor document publishes it
| Gain | 100 V/V fixed |
| Gain error | 0.05 per cent typical, 0.20 per cent maximum |
| Gain drift | 2.5 ppm per degree maximum |
| Nonlinearity | 0.5 ppm typical, 2.5 ppm maximum |
| Offset voltage | 5 microvolts typical, 25 microvolts maximum, referred to the input |
| Offset drift | 250 nanovolts per degree maximum |
| Common mode rejection, DC | 120 dB minimum, 132 dB typical |
| Common mode rejection at 50 kHz | 93 dB |
| Power supply rejection | 1 microvolt per volt typical, 10 maximum |
| Input bias current | 90 microamps |
| Common mode range | minus 4 volts to plus 80 volts, independent of the supply |
| Supply range | 2.7 volts to 5.5 volts |
| Quiescent current | 1.8 milliamps typical, 2.4 milliamps maximum |
| Bandwidth at 3 dB | 400 kHz at every gain |
| Bandwidth at 2 per cent distortion | 100 kHz at every gain |
| Slew rate | 2 volts per microsecond |
| Settling to 0.5 per cent | 9.6 microseconds at the 20 V/V gain, 9.8 at the 200 V/V gain |
| Voltage noise density | 40 nanovolts per root hertz |
| Reference divider accuracy | 0.01 per cent typical, 0.1 per cent maximum |
| Reference input range | 0 volts to the supply rail |
| Swing to the positive rail | 50 millivolts typical, 200 maximum into 10 kohm |
| Swing to ground | 1 millivolt typical, 10 maximum |
| Stable load capacitance | 1 nanofarad |
| Temperature range | minus 40 to plus 125 degrees |
| Vendor status | obsolete in the package addendum, 2500 piece reel printed |
| Catalogue code | INA240A3PW |
| Vendor string | INA240A3PW, obsolete; INA240A3PWR is the active row |
| Body | TSSOP, PW, eight pin, 3.00 by 4.40 millimetres |
| Marking | I240A3 |
Two bodies, eleven order codes and the rows the addendum marks obsolete
INA240A3PW comes in an 8 pin TSSOP of 3.00 by 4.40 millimetres and an 8 pin SOIC of 4.90 by 3.91 millimetres, both at moisture level 2 with a 260 degree peak and a one year floor life. The four gains are available in both bodies, so the body is a thermal and a footprint decision rather than a functional one: the TSSOP spreads heat better on a small board, the SOIC is easier to inspect and to rework by hand.
The addendum read for this page carries obsolete rows that are easy to order by accident. The tube codes INA240A2PW, INA240A3PW, INA240A4PW and the SOIC tube INA240A4D are printed Obsolete while the reel codes of the same gain and body are active, and INA240A2PWR is printed active with a dash in the quantity column instead of a reel size. A line that needs a few pieces for a pilot usually reaches for the tube, and that is exactly the row that is closed. Read the status column before the quantity column.
Where a PWM rejecting shunt monitor earns its place, and where it stops
INA240A3PW suits four kinds of channel: the phase current of a three phase motor drive, where the common mode steps at every switching edge; a solenoid or valve driver, where the current decays through a diode and the low side goes below ground; a telecom rectifier or a 48 volt power shelf, where the bus sits above the logic supply; and an actuator or pressure regulator loop that closes on current rather than on position.
It stops at four things. There is no digital output, so a converter and its reference are part of the channel. There is no isolation, so a mains referenced shunt needs an isolator behind the amplifier. The quiescent current of 1.8 milliamps typical rules out a battery instrument that sleeps. And the 10 millivolt full scale floor sets the shunt: at 10 millivolts and 25 microvolts of maximum offset, a shunt that develops less than 10 millivolts at the working current does not get more accurate by being larger, it gets slower and hotter. Our amplifier cross reference page covers the parts that trade one of those four for something else.
Four hundred kilohertz on all four gains
The bandwidth of INA240A3PW is 400 kHz at 3 dB and 100 kHz at 2 per cent distortion, and neither figure changes with the gain option. That is unusual for a current sense amplifier, where the gain stage normally trades bandwidth for gain, and it comes from the difference amplifier topology: the four gains are set by internal resistors on one die, so the 20 V/V and the 200 V/V option have the same pole.
The number that matters in a motor drive is the settling time, 9.6 microseconds at the 20 V/V gain and 9.8 at the 200 V/V gain to 0.5 per cent of the final value. A 20 kHz switching frequency leaves a 25 microsecond on-time at 50 per cent duty, and 9.6 microseconds is 38 per cent of it, so the sample has to be taken in the later part of the window. At 100 kHz switching the on-time is 5 microseconds and the output is still moving when the sample is taken, so the reading is low by whatever the output has not yet reached. A drive that samples at that speed needs a shorter settling time, not a faster converter.
Minus four volts of common mode, and why a solenoid needs it
The input of INA240A3PW is specified from 4 volts below ground to 80 volts above it, and the window does not move with the supply rail. The negative end is there for the flyback period of a solenoid or a relay: when the switch opens, the low side of the coil swings below ground and the shunt with it, and a monitor that stops at zero volts loses the reading for exactly the part of the cycle where the current is decaying.
The positive end covers a 48 volt telecom bus and a 72 volt battery pack with margin, again from a 3.3 or 5 volt rail, because the input divider is internal and the common mode window is independent of the supply. What the window does not cover is a bus that rings above 80 volts: above the limit the part is not specified, and the current that flows through the protection network becomes the error. A bus with a transient above 80 volts needs a series resistor on both inputs or a different part, and the decision belongs in the requirements rather than in a note on the drawing set.
What enhanced PWM rejection removes from the output
A motor phase carries a common mode step of tens of volts in a few hundred nanoseconds when the bridge switches, and a current sense amplifier sees it on both inputs at once. The rejection at 50 kHz on INA240A3PW is 93 dB, so a 60 volt step is attenuated to about 1.3 millivolts at the input, which at the 50 V/V gain is 65 millivolts of output movement rather than a recovery tail that lasts for milliseconds.
That figure is the one to compare between parts, because the DC rejection of 132 dB says nothing about a step. Amplifiers that quote only a DC number can still take tens of microseconds to recover, and the recovery lands inside the sampling window of the converter. The trade is bandwidth against rejection: 400 kHz is wide enough that the output follows a real current step, and the rejection network is narrow enough that the switching edge does not pass. A channel that filters the output to 10 kHz throws away most of the bandwidth and gains nothing on the edge, because the edge is already rejected at the input.
Twenty five microvolts against a ten millivolt full scale
The offset of INA240A3PW is 5 microvolts typical and 25 microvolts maximum referred to the input, with a drift of 250 nanovolts per degree maximum. Against a 10 millivolt shunt drop, which is the smallest full scale the family is specified for, the maximum offset is 0.25 per cent of full scale and the typical part is 0.05 per cent.
The drift row deserves the same arithmetic. At 250 nanovolts per degree over the 165 degree window from minus 40 to plus 125, the drift term is about 41 microvolts, which is larger than the maximum room temperature offset. A single point calibration at 25 degrees therefore buys less than the drift spec, and a channel that has to hold 0.5 per cent over temperature either runs a smaller temperature window, calibrates at the operating temperature, or uses the zero drift architecture for what it is: a guarantee that the offset does not wander, not a guarantee that it is zero.
A closed row on a released bill of materials is a schedule risk rather than a price question. Our obsolete part cross reference hub covers the equivalent active rows, and the obsolescence management page covers the wider question of a gain that is moving to one carrier.
Is the gain still available? Yes, as INA240A3PWR on a reel or INA240A3D in the SOIC body. The PW code without the R is the closed row.
Does the move change the reading? No. The die and the gain are the same; only the carrier and the marking change, so the scaling constant does not move.