Contact Us

INA232BIDDFR

Brand: Texas Instruments
Texas Instruments INA232BIDDFR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA232BIDDFR — Power Management & Signal Chain | Superb Automation

INA232BIDDFR

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA232BIDDFR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA232BIDDFR: the same 48 V monitor on a second address set

The INA232BIDDFR is the B address option of the INA232, a 16 bit current and power monitor that senses from 0.3 V to 48 V common mode on a supply from 1.7 V to 5.5 V. Electrically it is the same die as the A option: 0.3 percent maximum gain error, 50 uV maximum offset, 10 nA maximum input bias current, 20 mV or 80 mV full scale, 140 us to 8.244 ms conversion and averaging to 128 samples. What changes is the four addresses the part answers to, which is the whole reason the second option exists.

On a board with four isolated 48 V feeds the A option alone fills the bus. The B option adds four more, so eight monitors can answer on one I2C segment without a multiplexer. That matters because an I2C multiplexer is a part with its own failure mode, its own address and its own insertion loss on a bus that may already be running at 400 kHz through a backplane connector.

Key data for the INA232BIDDFR

Common mode0.3 V to 48 V, high side or low side, independent of the 1.7 V to 5.5 V supply
Full scale20 mV or 80 mV differential window at 16 bit, selectable per device in the configuration register
AccuracyGain error 0.3 percent maximum, offset 50 uV maximum, bias current 10 nA maximum
AddressingFour addresses from the single A0 pin in the B set; combined with the A option this covers eight devices on one bus
Timing140 us to 8.244 ms per conversion, averaging 1 to 128, conversion ready flag available
Supply1.7 V to 5.5 V, 300 uA typical, 1.2 V compliant I2C, minus 40 C to 125 C

Body, marking and reel data

BodyDDF, 8 pin SOT-23-THIN, the same land pattern as the A option
Reel3000 pieces on a large reel, with the same packing as the A option so a mixed kit can share a feeder
FinishNIPDAU, moisture level 1, unlimited floor life
MarkingTop side code plus the reel label; the address letter is not printed in a way that survives a 0402 beside it
Difference from AAddress set only, no electrical or mechanical difference anywhere in the table

Where the second address set pays for itself

A 1U power shelf with four rectifier slots and four battery strings is the obvious case: eight current monitors, one bus, no multiplexer, and a host that reads them in a fixed rotation. A remote radio head with two antenna branches and a tower mounted amplifier is another, because the alternative is running a second I2C segment up the mast.

The limit is the bus itself. Eight devices at 400 kHz with a 1.5 kOhm pull up and 200 pF of cable capacitance will not hold timing, so the segment usually has to drop to 100 kHz or move the pull up onto the board. The second limit is the alert pin: if all eight share one interrupt line the host still has to poll to find which one fired, so a board that leans on the alert usually assigns two or three monitors per interrupt rather than all eight. Where a bill of materials has both address options on it, the amplifier cross reference note lists the family by body and gain, and our pin to pin cross reference record confirms that the A and B options share one land pattern so a late change of address does not force a board revision.

Buyer questions on the INA232BIDDFR

Can the address be changed in circuit? No. The device samples the A0 pin on every bus transaction, but the pin is tied to one of four levels on the board, so changing the address means changing the strap. That is deliberate, because a monitor whose address can move under a host update is a monitor that can vanish from the bus after an update.

Is the B option a later revision? No. A and B are two options published side by side in the same revision of the document, with the same electrical table and the same orderable quantity.

What happens if both options land on the same address? The bus sees two devices acknowledging at once and the host reads corrupted data with no error flag. This is the one mistake the letter suffix is meant to prevent, and it is invisible until the board is in test.

Availability and ordering notes

INA232BIDDFR is active at 3000 pieces on a large reel with NIPDAU at moisture level 1, in the same body and at the same quantity as the A option. Because the two strings differ only in one letter, a purchase order that does not carry the letter risks the wrong option, and neither the marking nor the reel label is easy to read after the parts are on the board. We check the letter against the approved vendor list at goods in, and the check is recorded on the incoming inspection plan sheet so a mixed reel is caught before it reaches the line.