INA2191A1IYBJR
Product Specifications
INA2191A1IYBJR
Texas Instruments — Power Management & Signal Chain
Product Overview
The INA2191A1IYBJR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
INA2191A1IYBJR: dual 25 V/V monitor with 85 uA for both channels
The INA2191A1IYBJR is the lowest gain dual in the INA191 and INA2191 family, 25 V/V per channel, in a DSBGA 12 pin body. It reads a shunt between 0.2 V below ground and 40 V above it from a 1.7 V to 5.5 V supply, holds offset to 12 uV maximum with 0.13 uV per degree of drift, and draws 85 uA typical for both channels with 96 uA maximum over temperature and 200 nA maximum in shutdown. Input bias current is 100 pA typical, which is what makes a large shunt usable at microamp currents. Bandwidth at gain 25 is 45 kHz.
Gain 25 is the wide range end of the family and it is chosen for headroom rather than resolution. On a 3.3 V supply the output can swing about 3.2 V, so the maximum shunt drop is 128 mV; a 10 milliohm shunt therefore covers 12.8 A, and a 1 milliohm shunt covers 128 A. The part is aimed at battery powered equipment where the monitor must not become part of the standby load, which is why the quiescent current is specified at 25 C and over temperature separately.
Key data for the INA2191A1IYBJR
| Gain | 25 V/V per channel, the widest range of the five options from 25 to 500 |
| Input | Common mode minus 0.2 V to plus 40 V, bidirectional, 100 pA typical bias current |
| Accuracy | Offset 12 uV maximum, 0.13 uV per degree drift, gain drift 7 ppm per degree |
| Quiescent | 85 uA typical for the dual at 1.8 V, 96 uA maximum over temperature, 200 nA maximum in shutdown |
| Bandwidth | 45 kHz at gain 25 with a 10 pF load, falling to 27 kHz at gain 500 |
| Supply | 1.7 V to 5.5 V, which covers a single cell rail without a boost converter |
Body, marking and reel data
| Body | YBJ, DSBGA 12 pin, 1.79 mm square, the dual version of the 6 pin single channel body |
| Reel | 3000 pieces on a large reel, the only packing printed for this string |
| Finish | SNAGCU, moisture level 1 at 260 C with unlimited floor life |
| Marking | 29J1 on the A1 row, four characters that identify the dual die and the gain |
| Temperature | Minus 40 C to 125 C, specified over the full range rather than at 25 C |
A monitor that does not load the battery it measures
Standby current is where portable products are won and lost. A fuel gauge that draws 500 uA from a 1000 mAh cell is empty in three months before the product is ever switched on. At 85 uA for two channels, this part costs about 0.2 percent of a 1000 mAh cell per day, which is inside the budget of most portable products. The shutdown current of 200 nA maximum is the number that matters when the system decides to switch the monitor off entirely, and it is low enough that an external load switch is not needed to protect the battery.
The 12 uV offset is the other side of the same coin. At gain 25, 12 uV is 0.5 uA through a 10 milliohm shunt, so a reading of zero on a sleeping load is believable. The family's gain error is specified to 0.25 percent on the A2 to A5 rows, with the A1 row carrying its own wider figure in the electrical table, which is worth reading before an A1 part is used in a billing application. Where a portable programme is choosing between gain rows, our amplifier cross reference lists the family by gain, offset and quiescent current, and the medical device components page covers the traceability we keep for battery powered instruments.
Buyer questions on the INA2191A1IYBJR
Is the 85 uA figure for one channel or two? Both. The single channel device in the same family draws 43 uA typical, and the dual draws 85 uA with both channels enabled. The over temperature limit is 96 uA.
Can it run from a single 1.8 V rail? Yes, the supply floor is 1.7 V. The output swing then limits the shunt drop to about 1.7 V divided by the gain.
How is a DSBGA part handled on a line? With a stencil, a reflow profile and an inspection step that reads the four character marking. There is no lead to inspect, so the marking and the reel label carry the traceability.
Availability and ordering notes
The A1 string is active at 3000 pieces on a large reel with SNAGCU plating and moisture level 1, marking 29J1. The single channel family member uses a 6 pin body, so a board cannot take both without a land change. We read the gain and the body from the reel label, keep the plating and date code on the date code management note, and confirm the A1 gain error figure against the electrical table before quoting it into a specification.