INA211AIDCKR
Product Specifications
INA211AIDCKR
Texas Instruments — Power Management & Signal Chain
Product Overview
The INA211AIDCKR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
INA211AIDCKR: 500 V/V zero drift monitor for small shunt drops
The INA211AIDCKR is the 500 V/V member of the INA210 to INA215 family, a bidirectional voltage output current shunt monitor in a 6 pin SC70 body. It reads a shunt between 0.3 V below ground and 26 V above it from a 2.7 V to 26 V supply, holds offset to 35 uV maximum on the INA210 row, and drifts 0.5 uV per degree with 10 ppm per degree of gain drift. At gain 500 the bandwidth is 7 kHz, the lowest in the family and still two orders above the bandwidth of a battery fuel gauge loop.
The reason to buy 500 V/V rather than 50 is a shunt that cannot be made larger. A 1 milliohm shunt at 100 mA develops 100 uV, which at gain 50 is 5 mV and at gain 500 is 50 mV. The second number survives a 12 bit converter with a 3.3 V reference: it is about 60 codes, while 5 mV is 6 codes and inside the offset window of most alternatives. That is the whole argument for the high gain rows, and it is why they are common in portable equipment where the shunt is a PCB trace or a small resistor.
Key data for the INA211AIDCKR
| Gain | 500 V/V, one of six options from 50 to 1000 in the same body |
| Input | Common mode minus 0.3 V to plus 26 V, bidirectional, independent of the supply |
| Accuracy | Offset 35 uV maximum on the lowest gain row, 0.5 uV per degree drift, gain error 1 percent on A and B rows |
| Bandwidth | 7 kHz at gain 500 with a 10 pF load, 80 kHz at gain 50 through 4 kHz at gain 1000 |
| Supply | 2.7 V to 26 V, 100 uA maximum quiescent current, no shutdown pin |
| Output | Voltage output referenced to the REF pin, ground referred when REF is tied low |
Body, marking and reel data
| Body | DCK, SC70 6 pin, 2.00 mm by 1.25 mm, with the UQFN 10 pin as the alternative body |
| Reel | 3000 pieces on a large reel for the R suffix, 250 pieces on a small reel for the T suffix |
| Finish | NIPDAU, moisture level 2 at 260 C with a one year floor life, level 1 on some rows |
| Marking | The addendum prints a three character code per gain, so the reel label is the only reliable gain identifier |
| Temperature | Minus 40 C to 125 C on every active row of the family |
High gain, small signal and the noise floor
A 500 V/V amplifier amplifies its own offset along with the signal, so the input referred offset is what decides the smallest readable current, not the output swing. At 35 uV input referred and a 1 milliohm shunt, the floor is 35 mA; at 100 milliohm it is 350 uA. That arithmetic is the reason the family pairs a high gain with a tight offset instead of simply raising the gain, and it is the first thing to check when a customer reports a reading that never reaches zero.
The second limit is the shunt tolerance and its temperature coefficient. A 1 percent shunt that drifts 100 ppm per degree across a 60 degree excursion adds 0.6 percent, which is larger than the amplifier gain error. Budgeting the amplifier alone is the classic mistake. Where a current sense chain is being rebuilt, our amplifier cross reference lists the family by gain and offset, and the BOM shortage recovery page covers how a missing gain option is bridged without a board change.
Buyer questions on the INA211AIDCKR
Why is the bandwidth only 7 kHz? Bandwidth falls as gain rises in a fixed gain amplifier, and this row is at the top of the range. It is enough for a fuel gauge or a power monitor and not enough for a fast overcurrent trip.
Can the gain be changed without a board change? Yes inside the family, because every gain shares the SC70 land pattern. The output scale changes, so the host code and the calibration table change with it.
What body does the DCK suffix mean? SC70 6 pin. The addendum for this row prints the UQFN body against the plain string in one table and the SC70 against the lettered rows, so the body is confirmed from the reel label rather than the family table alone.
Availability and ordering notes
The lettered rows are active at 3000 pieces on a large reel, and the addendum carries a moisture level that differs between the plain and lettered rows of the same string, level 2 against level 1. That difference decides whether a bake is needed, so it is read per row and not per family. The gain is not marked in a form a person can read reliably, which makes a mixed carton the main risk on a line that runs two gains; the incoming inspection plan page sets out the check we run on receipt. The gain is not printed in a readable form, so an incoming check of the body and the moisture card is what stands between a mixed carton and the line.