INA186A1QDCKRQ1
Product Specifications
INA186A1QDCKRQ1
Texas Instruments — Power Management & Signal Chain
Product Overview
The INA186A1QDCKRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
INA186A1QDCKRQ1: 25 V/V zero drift current sense amplifier with enable in the six pin SC70
INA186A1QDCKRQ1 is a low power bidirectional current shunt monitor from the INA186 family, the 25 V/V member in the SC70 body in a SC70 body of 6 pins. It senses at common mode from minus 0.2 V to plus 40 V from a 1.7 V to 5.5 V supply, draws 48 uA typical and 65 uA maximum, and holds a plus or minus 50 uV offset with 0.5 uV per degree of drift through a chopper stabilised input stage. The 500 pA typical input bias current is what lets a microamp level measurement use a large shunt without the amplifier current swamping the signal, and that combination is the reason this part appears in battery and server supply monitoring rather than in motor drive.
Order code and package
| INA186A1IDCKR | SC70 DCK body, 6 pins, 3000 pieces on a large reel, Active in the addendum dated 5 March 2026, NIPDAU finish, moisture level 2 with a one year floor life, marking 1E7, minus 40 to plus 125 degrees |
| INA186A1QDCKRQ1 | the catalogue string carries a Q1 suffix for the automotive grade, and the automotive grade is a separate publication, INA186-Q1. The addendum in this industrial file prints the industrial rows only, so the Q1 reel and moisture rows are not in the table above and have to be confirmed from the automotive document or the reel label |
| INA186A1IDCKT | the same DCK body on a 250 piece small reel, moisture level 2, which is the prototype quantity |
| INA186A1IDDFR | SOT-23-THIN DDF body, 8 pins, 3000 pieces on a large reel at moisture level 1 with no floor life limit, marking 1ZLW, and this is the body that carries both the enable pin and the reference pin |
| INA186A1IYFDR | DSBGA YFD body, 6 balls, 3000 pieces on a large reel with an SNAGCU finish, marking 1E8, and this is the smallest body in the family but the one that cannot do bidirectional sensing |
Electrical parameters that decide the application
| Common mode range | minus 0.2 V to plus 40 V, independent of the supply, which covers a 36 V rail and the reverse excursion of a low side shunt |
| Supply | 1.7 V to 5.5 V single rail, 48 uA typical and 65 uA maximum quiescent, 10 nA to 100 nA in the disabled state |
| Offset voltage | plus or minus 50 uV maximum at a 1.8 V supply with zero sense, and the zero drift architecture holds it across temperature |
| Offset drift | 0.5 uV per degree maximum, which is what makes the offset limit meaningful over minus 40 to plus 125 degrees |
| Gain | 25 V/V on the A1 member, against 50, 100, 200 and 500 V/V on A2 to A5, all fixed in silicon |
| Gain error | plus or minus 1 per cent maximum, with 0.04 per cent typical and 10 ppm per degree of gain drift |
| Common mode rejection | 120 dB minimum and 150 dB typical, quoted over the whole 40 V common mode window |
| Input bias current | 0.5 nA typical and 3 nA maximum, which is the figure that permits a 10 kOhm shunt without a bias error term |
| Bandwidth | 35 kHz on the 500 V/V member with a 10 pF load, and the lower gain members are faster, so bandwidth falls as gain rises |
| Slew rate and settling | 0.3 V per microsecond, 30 us settling to within 1 per cent of final value after a current step |
| Noise | 75 nV per root hertz referred to the input, which at 25 V/V is 1.9 uV per root hertz at the output |
| Temperature | minus 40 to plus 125 degrees on every body, industrial and automotive alike |
Family variants and how they differ
| Enable and reference pins by body | the enable pin exists only on the DDF and YFD bodies and the reference pin only on the DDF and DCK bodies, so a circuit that needs the part powered down between measurements has to use the DDF body and cannot use the SC70 |
| DSBGA sensing direction | the YFD body measures in one direction only while the SC70 and the DDF bodies do bidirectional sensing, so the smallest package is also the least flexible and that trade has to be made deliberately |
| INA180 as the cheaper neighbour | 350 kHz and a 26 V window at 260 uA, but 150 uV of offset and 1 uV per degree of drift, which is three times the offset of this part and no chopper |
| INA190 as the tighter neighbour | a 1.7 V to 5.5 V supply and a 920 kHz bandwidth at 25 V/V with a similar offset class, for the case where 35 kHz at the top gain is too slow |
| INA296A as the high voltage alternative | minus 5 V to 110 V common mode with a 1.1 MHz bandwidth at every gain, at 2.5 mA of supply current, for 48 V buses that this 40 V window cannot reach |
Points to check before this part goes on a BOM
The 40 V common mode window is what separates this part from the INA180 family. A 36 V industrial rail sits inside it with 4 V of headroom, and the minus 0.2 V at the bottom covers the undershoot of a low side shunt when a motor brakes. What it does not cover is a 48 V telecom bus, where the INA296A and its 110 V operational rating is the part, and it does not cover a load dump on a 24 V automotive rail, which needs an external clamp regardless of the amplifier rating.
The 500 pA input bias current is the specification that makes a microamp measurement possible. A 10 kOhm shunt carrying 1 mA drops 10 V, which is far too much; the same shunt carrying 10 uA drops 100 mV, and the bias current contributes 5 uV across it. That ratio is why the part is used in battery gauges and server supply monitoring, where the current range spans three decades and the shunt cannot be made large enough to suit a coarse amplifier.
The chopper stage is what delivers 50 uV of offset and 0.5 uV per degree of drift, and it also puts switching artefacts on the input. The vendor specifies the input filter and the output capacitor, and the practical consequence is that a source impedance above a few kilohertz of corner frequency will convert some of that chopping into a differential error. A 100 nF across the inputs close to the device, with matched 100 ohm resistors, is the arrangement the datasheet shows.
Bandwidth is inversely tied to gain and the 35 kHz figure belongs to the 500 V/V member, the slowest one. At 25 V/V the same stage is faster, which is why an overcurrent protection loop on a 25 V/V part can act in tens of microseconds. A current loop that needs 100 kHz of small signal bandwidth needs a different family, and the INA190 or the INA296A are the two the vendor offers for that.
The reference pin only exists on some bodies and that changes what the part can do. With a reference pin the output can be offset for bidirectional sensing; without it the output sits at ground with zero current and only measures one direction. A circuit copied from a DDF page onto the SC70 body loses bidirectional sensing without any change in the part number prefix, and that is a connection level trap rather than a purchasing one.
The Q1 suffix in this catalogue string is not covered by the document this page was built from. The industrial addendum lists DCK, DDF and YFD rows with their own reel sizes and moisture levels, and the automotive grade has its own publication. An order for INA186A1QDCKRQ1 therefore needs the automotive addendum row or the reel label, and the industrial row must not be supplied as an equivalent without saying so.
Working the error budget at 25 V/V
With a 25 V/V gain and a 50 uV offset, the output offset is 1.25 mV. On a 3.3 V converter input that is 0.04 per cent of full scale, which is small enough that the gain error of 1 per cent dominates at any reading above a twentieth of full scale. Below that the offset takes over, and the crossover sits at 5 mV of sense, which on a 10 milliohm shunt is 500 mA.
At the top of the current range the shunt self heating matters more than either term. A 10 milliohm shunt at 10 A dissipates 1 W, and the temperature coefficient of a metal strip shunt of 50 ppm per degree moves the reading by the same amount as a hundred degrees of amplifier drift would. The amplifier is the accurate half of that pair, which is why the shunt specification belongs in the same conversation as the amplifier choice.
Where the enable pin earns its place
The 10 to 100 nA disabled current on the DDF and YFD bodies is what a battery powered product needs when it samples a current once a second rather than continuously. On the SC70 body the same silicon runs at 48 uA all the time, which over a year on a coin cell is the difference between a viable product and a dead one. The choice of body is therefore a power budget decision before it is a footprint decision.
Where this order code fits
Notebook and smartphone battery monitoring, consumer chargers, baseband units, server power supplies and battery test equipment are the applications the vendor names, and all of them measure a current that spans several decades on a shunt that cannot be large. Teams comparing it with a neighbouring part start from our Amplifier Cross Reference page, and teams replacing a part that has gone end of life start from the How to Verify a Drop in Replacement page.
Questions buyers ask
Does the SC70 body have an enable pin? No. The enable pin and the reference pin exist only on the DDF body; the reference pin also exists on the DCK body, but the enable pin does not.
Can the DSBGA body measure current in both directions? No. Only the SC70 and DDF bodies do bidirectional sensing, and the DSBGA body measures one direction.
Is the Q1 automotive grade in this document? No. This is the industrial document, and the Q1 rows come from the separate automotive addendum.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Incoming Inspection Plan page sets out the checks that keep a substitute from failing on the bench.