Contact Us

INA185A1IDRLR

Brand: Texas Instruments
Texas Instruments INA185A1IDRLR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA185A1IDRLR — Power Management & Signal Chain | Superb Automation

INA185A1IDRLR

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA185A1IDRLR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA185A1IDRLR: the 20 V/V current sense amplifier in SOT-563

INA185A1IDRLR is the 20 V/V gain member of the INA185 family, a bidirectional current sense amplifier in a six pin SOT-563 body on a 4000 piece reel. The body measures 1.6 mm by 1.6 mm and the whole part is 39 percent smaller in footprint than the SC70 package that the same die is also offered in, which is the reason this string exists: it fits beside a shunt on a board where the sense resistor is already the largest component in the loop.

SBOS378A, revised November 2023, covers four gain options: 20 V/V on the A1 devices, 50 V/V on the A2, 100 V/V on the A3 and 200 V/V on the A4. The gain letter is part of the order code, so an A1 and an A4 are not interchangeable even though they share a datasheet, a package and a pinout.

What follows is what the 20 V/V gain buys, the accuracy rows that hold at 26 V common mode, the difference between the four gain options in bandwidth and error, and the lifecycle detail on the DRL body.

What the lowest gain in the family is for

A 20 V/V gain suits a shunt that already develops a large drop. A 10 milliohm shunt at 10 A drops 100 millivolts, which becomes 2 V at the output with this gain, so a 3.3 V converter reads it directly without a second stage. The same shunt with a 200 V/V part would saturate the output at 1 A, which is why the gain has to be chosen from the current range and not from the resolution alone.

Orderable codeINA185A1IDRLR
Gain20 V/V
BodySOT-563, 6 pins, 1.60 mm by 1.60 mm
Carrier4000 pieces on a large reel
Common mode rangeminus 0.2 V to 26 V
Supply voltage2.7 V to 5.5 V
Supply current260 microamps maximum
Bandwidth, A1 devices350 kHz
Offset voltage at zero common mode55 microvolts maximum
Offset voltage at 12 V common mode, A4100 microvolts maximum
Offset drift0.5 microvolts per degree maximum
Gain error, A1, A2 and A3plus or minus 0.2 percent maximum
Output slew rate2 volts per microsecond
Operating temperatureminus 40 to 125 degrees
Part marking1DV
Moisture ratinglevel 1, unlimited floor life at 260 degrees

Accuracy at 26 V common mode

The common mode range of minus 0.2 V to 26 V is independent of the supply, so a 3.3 V supplied part can measure current in a 24 V rail. That is the property that lets the same circuit sit on a 48 V telecom board with a divider or on a 24 V industrial board directly, and it is why the part appears in motor control and battery management boards where the rail and the logic supply are far apart.

Offset of 55 microvolts maximum at zero common mode widens to 100 microvolts on the A4 devices at 12 V, and the family table prints the wider figure for the higher gain parts rather than for the high voltage case alone. On a 20 V/V part, 55 microvolts of input offset is 1.1 millivolts at the output, which is 0.03 percent of a 3.3 V full scale and well inside a 12 bit converter. On a 200 V/V part the same offset is 11 millivolts, which is 0.3 percent, and that is the arithmetic behind the choice of gain for a small shunt.

Gain error of 0.2 percent on the A1, A2 and A3 devices is the tightest row in the family and it is printed as a maximum over the full temperature window rather than at room. That figure is what makes the part usable for a measurement that ships with a calibration certificate, because a 0.2 percent gain error can be trimmed in production with a single point calibration and the drift after that is 0.5 microvolts per degree on offset and a few parts per million on gain.

Bandwidth, slew and the loop

350 kHz on the A1 devices is the widest bandwidth in the family, and it falls as the gain rises. For an over current protection path that has to react inside a switching period, the A1 part with the 350 kHz bandwidth and the 2 V per microsecond slew is the right choice, because a 200 V/V part would be ten times slower and would let the current overshoot before the comparator sees it.

For a motor control loop the bandwidth sets how fast the current loop can close. A 20 kHz loop with a 350 kHz amplifier has enough phase margin that the amplifier is not the limiting element, and the limit becomes the shunt inductance and the sampling instant. That is the configuration used in field oriented control, where the current is sampled once per switching period and the amplifier has to settle within a few microseconds.

For a battery monitor the speed is irrelevant and the offset drift is everything, because the measurement runs at low current for hours. The 0.5 microvolts per degree drift on this part is 50 microvolts over a 100 degree swing, which on a 10 milliohm shunt is 5 milliamps of apparent current, and that is the figure that decides whether the fuel gauge drifts over a season.

Reading the DRL suffix in the addendum

The addendum prints both bodies and both carrier quantities, and the prefixes are where buyers get caught. The DRL rows are the SOT-563 body at 4000 pieces on a large reel, and the DCK rows are the SC70 body at 3000 pieces on a large reel, and several of the DRL rows in the family are printed as obsolete while the corresponding DCK row is active. This specific code, the A1 with the DRL body, is printed active with a nickel palladium gold finish and a level 1 moisture rating.

The level 1 rating is worth noting for a production line: no bake is required at any point in the floor life, which removes a step that level 3 parts force on a partially used reel. On a 4000 piece reel that is the difference between a line that can open a reel for a small build and one that has to plan bakes around the schedule.

The 39 percent footprint reduction against the SC70 body is real but it comes with a tighter pad geometry, so a board that was laid out for the SC70 cannot take the SOT-563 without a board change. The amplifier cross reference page lists the gain options across the family and their second sources, and the date code management page covers how we treat a level 1 reel that has been open for a year.

Questions that come with this string

Can an A1 be substituted for an A4? No. The gain is part of the die trim, so a 20 V/V part in a 200 V/V position reads ten times low. The pinout is the same, which is exactly why the mistake happens.

Is the part bidirectional? Yes, the output sits at the reference level with zero current and swings either side of it, so the same shunt measures charge and discharge. The reference pin has to be driven from a low impedance source, otherwise the rejection of the reference pin becomes part of the error budget.

What sets the maximum common mode? 26 V is the printed limit and it is a process limit rather than a supply limit, so it does not rise with a higher supply. A 48 V rail needs a divider or a different part.

Does the part need an input filter? A pair of 10 ohm resistors and a differential capacitor at the input pins is the usual addition where the shunt sits on a switching node, because the 350 kHz bandwidth will otherwise see the switching edge as a signal. That filter also protects the inputs against a shunt that fails open. The incoming inspection plan covers the reel level checks that come before a lot is released.