Contact Us

INA154U

Brand: Texas Instruments
Texas Instruments INA154U is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA154U — Power Management & Signal Chain | Superb Automation

INA154U

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA154U from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA154U: unity gain at 3 MHz from a 25 kohm network

INA154U is a unity gain difference amplifier with a 25 kohm network on each input, 3.1 MHz of bandwidth, 14 volts per microsecond of slew rate and 750 microvolts of maximum offset. It is the fast member of the family and the one that gets used where a differential signal has to be received at speed: a line receiver, a synchronous demodulator, a current shunt on a switching node.

The U grade matters here more than on a slow part, because a fast channel is usually a wideband channel and a wideband channel cannot be trimmed at every operating point. Seven hundred and fifty microvolts against the UA grade's 1500 is the difference between one trim step and two, and 2 microvolts per degree against a typical curve is the difference between a calibration that holds and one that has to be repeated.

INA154U as the vendor document publishes it

Gain1 V/V fixed
Gain error0.02 per cent typical, 0.05 maximum
Gain drift1 ppm per degree typical, 10 maximum
Nonlinearity0.0001 per cent typical, 0.001 maximum of full scale
Offset100 microvolts typical, 750 maximum
Offset drift2 microvolts per degree typical, 20 maximum
Supply rejection5 microvolts per volt typical, 60 maximum
Input impedance50 kohm differential, 50 kohm common mode
Common mode rejection80 dB minimum, 90 typical
Voltage noise2.6 microvolts peak to peak, 52 nanovolts per root hertz at 1 kHz
Bandwidth3.1 MHz small signal
Slew rate14 volts per microsecond
Settling to 0.01 per cent3 microseconds on a 10 V step
Overload recovery3 microseconds from a 50 per cent overdrive
Output swingwithin 1.8 volts of the positive rail into 10 kohm
Quiescent current2.4 milliamps typical, 2.9 maximum
Supply rangeplus or minus 4 to plus or minus 18 volts
Current limit60 milliamps continuous
Stable load capacitance500 picofarads
Bodyeight pin SOIC
Temperature rangeminus 40 to plus 85 degrees
Catalogue codeINA154U
GradeU, 750 microvolts maximum offset
Network25 kohm per input, laser trimmed, gain fixed at 1

Unity gain from a 25 kohm network

INA154U is a unity gain difference amplifier built from a precision op amp and a pair of 25 kohm resistors on each input, trimmed as a ratio to a gain of 1 V/V with 0.02 per cent typical and 0.05 per cent maximum gain error on the U grade, 0.1 on the UA. Nonlinearity is 0.0001 per cent typical and 0.001 maximum, and the ratio holds over temperature at 1 ppm per degree typical and 10 maximum.

The network is not adjustable and the gain is not meant to be changed, which simplifies everything downstream: the input impedance is fixed at 50 kohm, the bandwidth is fixed at 3.1 MHz and the common mode range is a known function of the supply. On a differential line receiver or a current shunt monitor that is exactly the right trade, because the alternative is four resistors whose ratio has to be trusted and whose tracking over temperature has to be measured.

3.1 MHz and 14 volts per microsecond

INA154U carries 3.1 MHz of small signal bandwidth and a 14 volt per microsecond slew rate, with a settling time of 2 microseconds to 0.1 per cent and 3 to 0.01 on a 10 V step into a 100 pF load, and overload recovery of 3 microseconds from a 50 per cent overdrive. That combination is fast for a difference amplifier and is the reason the family lists synchronous demodulation among its applications.

The scan arithmetic is generous: sixteen channels at 3 microseconds is 48 microseconds, so the amplifier is not the limit in any multiplexed system built around it. The slew rate sets the large signal behaviour, and a 10 V step at 14 volts per microsecond is 0.7 microseconds of ramp, which is consistent with the 2 microsecond settling figure. What the part will not do is drive a heavy load at that speed: the output current limit is 60 milliamps and the stable load capacitance is 500 picofarads.

750 microvolts on the U grade and 1500 on the UA

Offset on INA154U is 100 microvolts typical and 750 maximum on the U grade referred to the output, with 2 microvolts per degree of drift; the UA grade is 1500 microvolts maximum with a drift the vendor leaves to the typical curve. Supply rejection is 5 microvolts per volt typical and 60 maximum over plus or minus 4 to plus or minus 18 volts, and the noise is 2.6 microvolts peak to peak from 0.1 to 10 Hz and 52 nanovolts per root hertz at 1 kHz.

At unity gain the offset is the same number at the input and at the output, which makes the budget simple: 750 microvolts on a plus or minus 10 volt span is 0.0075 per cent of full scale and a sixteenth of what a 16 bit converter resolves. The drift is the term that matters on a channel calibrated once, 2 microvolts per degree or 90 microvolts over 45 degrees, an eighth of the initial offset. That is why the U grade exists and why the UA grade is specified with a typical drift curve rather than a limit.

2.4 milliamps and plus or minus 4 to 18 volts

INA154U draws 2.4 milliamps typical and 2.9 maximum, from a supply between plus or minus 4 and plus or minus 18 volts, and the output reaches to within 1.8 volts of the positive rail and 1.6 of the negative into a 10 kohm load. Current limit is 60 milliamps continuous into the common point and the part is stable into 500 picofarads.

The 2.4 milliamps is high next to the 570 microamps of the INA145 and that is the cost of 3 MHz and 14 volts per microsecond in the same body. In a mains powered instrument it is irrelevant. In a battery instrument it rules the part out unless the measurement is fast and intermittent, in which case the 4 volt floor of the supply window is the second constraint: a 3.3 V rail is below the minimum, so the part needs a boosted rail or a different family.

50 kohms on both inputs, and the imbalance it punishes

The input impedance of INA154U is 50 kohm differential and 50 kohm common mode, which is symmetric and high enough that a 1 kohm source loses 2 per cent of the signal and a 100 ohm source 0.2 per cent. Common mode range extends beyond both rails, to twice the positive rail minus 4 volts and twice the negative rail plus 2 volts with the output at zero.

Symmetric does not mean insensitive. Two per cent of signal loss from a 1 kohm source is forty times the 0.05 per cent gain error, so a source resistance belongs in the calibration, and any difference between the two source resistances converts common mode into a differential error at the rate of the mismatch. A protection resistor added to one input for a cable fault has to be matched on the other, and a filter capacitor on one input has to be matched on the other for the same reason at frequencies above a few hundred kilohertz.

What a unity gain difference amplifier is for, and where it stops

INA154U earns its place as an instrumentation building block: a differential line receiver on a long cable, a current shunt monitor on a high side rail within its common mode window, a summing amplifier, a synchronous demodulator front end, or the input stage of a discrete instrumentation amplifier where the gain is set by a following stage. In each case the value is the trimmed 25 kohm ratio, which no four resistor build matches without a matched network.

It stops at three things. A source impedance above a few kilohertz of impedance times capacitance, where the 50 kohm input and the 3 MHz bandwidth together produce a phase shift that erodes the rejection. A common mode beyond twice the supply, which is generous but finite. And a supply below 4 volts, because the window starts there. A channel that needs any of those is a different part, and the family that covers it is the programmable gain one rather than this fixed unity gain member.

At 2.4 milliamps the part is a mains powered choice, and the plus or minus 4 volt supply floor rules out a 3.3 V rail without a boost. Our amplifier cross reference page covers the lower current members of the family, and the BOM scrubbing page covers the code match before the build.

Can the gain be changed? No. The 25 kohm network is fixed and the gain is 1. A channel that needs gain needs a second stage or a different family.

Is 3.1 MHz the usable bandwidth? It is the small signal figure. A 10 V step at 14 volts per microsecond takes 0.7 microseconds of ramp and settles in 2 to 3, so the part is usable at a few hundred kilohertz on full scale, not at 3 MHz.