INA133U-2K5
Product Specifications
INA133U-2K5
Texas Instruments — Power Management & Signal Chain
Product Overview
The INA133U-2K5 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
INA133U-2K5: the hyphen spelling of the plain grade reel, and the common mode that goes beyond both rails
The INA133U-2K5 is the hyphen rendering of the plain grade reel, which the addendum prints as INA133U/2K5 at 2500 pieces. It is one part under two spellings, and the electrical rows are the U bin rows: 450 µV of offset, 5 µV per degree of drift, 0.05 per cent of gain error and 80 dB of minimum rejection at a common mode range that reaches twice each supply minus 3 V.
That common mode range is the reason the part exists in industrial racks. On a plus or minus 15 V supply the inputs work from minus 27 V to plus 27 V, so a shunt sitting at the top of a battery string or in the leg of a half bridge is inside the window, and the absolute maximum input of 80 V means a fault voltage does not destroy the part even when the output cannot follow it.
The INA133U-2K5 rows as the addendum publishes them
| Part class | High speed unity gain difference amplifier, trimmed 25 kΩ network |
| Vendor status | Active, production |
| Data sheet | SBOS115B, revised January 2026 |
| Addendum row it normalises to | INA133U/2K5, 2500 pieces |
| Grade | U bin |
| Gain | 1 V/V fixed |
| Input offset voltage | 450 µV maximum |
| Offset drift | 5 µV per degree maximum |
| Common mode rejection | 80 dB minimum |
| Common mode range | 2 times each supply minus 3 V |
| Absolute maximum input | 80 V |
| Input impedance | 50 kΩ differential |
| Bandwidth | 1.5 MHz small signal |
| Slew rate | 5 or 20 V per microsecond depending on chip origin |
| Settling | 5.5 µs to 0.01 per cent |
| Supply range | Plus or minus 2.25 V to plus or minus 18 V |
| Quiescent current | 950 µA typical |
| Body | SOIC, D outline, 8 pins |
| Carrier | 2500 pieces on a large reel |
| Moisture level | Level 3, 168 hour floor life |
Two chip origins, and 5 against 20 volts per microsecond
The same part number can arrive from two fabrication flows, and the vendor labels the difference by chip site origin. On INA133U-2K5 the slew rate is 5 volts per microsecond on the SHE flow and 20 volts per microsecond on the RFB flow, a factor of four on a row that no distributor listing shows. Voltage noise moves the other way: 57 nanovolts per root hertz at 1 kHz on SHE and 20 on RFB, and the common mode rejection minimum moves from 80 to 74 dB between the U and UA bins on top of that.
For a servo loop running at a few kilohertz either flow is fine. For a channel that has to settle in a few microseconds after a multiplexer step, the 5 volt per microsecond flow is a 20 microsecond edge on a 10 V step and the RFB flow is 5 microseconds, which is the difference between a working scan rate and a specification that is met only on paper. The flow is printed on the reel label and in the lot record, not on the part.
1.5 MHz at unity gain from a difference amplifier
INA133U-2K5 is the fast member of the unity gain difference amplifier group: 1.5 MHz of small signal bandwidth against the 300 kHz of the INA132, with the same on-chip resistor network and the same eight pin body. The bandwidth is what a servo feedback path or a string inverter current loop needs, because a 20 kHz loop with 60 degrees of phase margin wants an amplifier an order of magnitude faster than the loop, and a 300 kHz part leaves no margin.
The network is four 25 kohm resistors trimmed as a set, giving a differential input impedance of 50 kohm and a common mode impedance of 25 kohm. Gain is fixed at 1 V/V, gain error is 0.05 per cent maximum on the U bin and 0.1 per cent on the UA bin, and nonlinearity is 0.001 and 0.002 per cent of full scale. At unity gain the offset is quoted referred to the output, so the input and output numbers are the same.
450 microvolts on the U and 900 on the UA
The offset window on INA133U-2K5 is 450 microvolts maximum on the U bin and 900 microvolts on the UA bin at a plus or minus 15 V supply, doubling to 750 and 1500 microvolts at plus or minus 5 V, with a drift of 5 microvolts per degree on both. The supply dependence is unusual and worth reading twice: the same part is twice as loose on a 10 V total supply as on 30 V, so a 5 V single rail application starts with a 1.5 mV window on the UA bin.
Because the offset is referred to the output and the gain is one, a 900 microvolt offset is 900 microvolts at the output, which against a 2 V full scale is 0.045 per cent and against a 100 mV shunt signal is 0.9 per cent. On a shunt monitor that is a real error and it is why the U bin exists; on a servo feedback path it is trimmed by the loop. Long term stability is 0.3 microvolts per month on both bins.
The 25 kohm network loads the source and unbalances it
Each input of INA133U-2K5 sees 25 kohm to the amplifier, and the differential pair presents 50 kohm. Across a 100 ohm shunt that is a 0.2 per cent gain loss, which is larger than the 0.05 per cent gain error row and has to be calibrated. Across a 10 kohm source the loss is 17 per cent and the whole measurement is a divider, which is the point at which a buffer belongs in front of the part rather than after it.
The network is ratio matched, so the loading is common to both inputs and cancels as long as the source impedances match. A protection resistor in one leg, a connector with different contact resistance, or a filter capacitor on one side breaks that match and converts common mode into a differential error. On a board the two input traces should be the same length, the same width and the same distance from any plane, which is ordinary practice for a differential pair and easy to forget on a DC channel.
A common mode range of twice the supply, minus three volts
The input common mode range of INA133U-2K5 extends beyond both rails: from 2 times the negative rail plus 3 V to 2 times the positive rail minus 3 V. On a plus or minus 15 V supply that is minus 27 V to plus 27 V, and on a plus or minus 5 V supply it is minus 7 V to plus 7 V. The absolute maximum input is 80 V, so the part survives a common mode it cannot measure, which is the useful half of the specification on an industrial rack where a transducer cable can pick up a fault voltage.
That range is what allows the part to sit directly across a shunt in a motor leg or a battery string, where the common mode is neither near ground nor inside the supply. It also means the inputs are not protected by the supply rails: a 40 V common mode on a plus or minus 5 V supply is inside the input window and outside the supply, and the output will do something the loop may not expect. The window has to be checked against the supply, not assumed from it.
950 microamps, 5.5 microseconds and the dual INA2133
Quiescent current on INA133U-2K5 is 950 microamps typical, which is five times the INA132 and the price of the 1.5 MHz bandwidth. Settling to 0.01 per cent takes 5.5 microseconds, short circuit current is 32 mA source and 25 mA sink on the SHE flow and 70 mA both ways on RFB, and the output is stable into 1000 pF. Output swing stops 1.5 V short of each rail under a gain error condition, which on plus or minus 15 V leaves plus or minus 13.5 V of usable range.
The single channel is the eight pin SOIC. The dual INA2133 is the fourteen pin SOIC with two independent channels at 8.65 by 6 mm, sold in 50 piece tubes, and it is specified over minus 55 to plus 125 degrees rather than the minus 40 to plus 85 of the single. On a multi channel board the dual saves one package and one reel but costs board area, and the wider temperature range is worth having when the board sits near a heatsink.
Buying INA133U-2K5
Two strings, one reel, one addendum row. The duplicate is a data problem rather than a supply problem, and it is worth fixing in the item master before the next MRP run rather than after a shortage that the system created. Our BOM scrubbing page describes the check.
The other decision is whether the INA2133 dual is a better buy. Two channels in a fourteen pin SOIC at 50 pieces per tube is cheaper per channel and saves a placement, and it is specified over minus 55 to plus 125 degrees rather than minus 40 to plus 85. On a board with two shunts, the dual is usually the right answer; on a board with one, it is not.
Questions that arrive with this part number
Whether the hyphen changes the part is the first question, and it does not. Whether the common mode range is a guarantee or a typical is the second, and it is a minimum and maximum row in the table, measured at zero output with the supply at both 15 V and 5 V.
The third is what happens outside the window. The output stops following, but the part is not damaged until 80 V at the input, and that asymmetry is the useful part of the specification: a fault can be survived without being measured. The fourth is the input load, 25 kΩ per leg, which unbalances if the two source resistances differ and turns common mode into a differential error.