Contact Us

INA129U-2K5

Brand: Texas Instruments
Texas Instruments INA129U-2K5 is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA129U-2K5 — Power Management & Signal Chain | Superb Automation

INA129U-2K5

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA129U-2K5 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA129U-2K5: the same 2500 piece reel under the hyphen spelling of the suffix

The INA129U-2K5 is the catalogue rendering with a hyphen where the vendor addendum prints a slash. It is the plain grade eight pin SOIC from a 2500 piece reel, the same body, the same marking and the same electrical rows as INA129U/2K5, and the hyphen exists because some catalogue systems cannot carry a slash in a part number. The check that matters is whether the code on the purchase order matches a published row once the separator is normalised.

The part itself is the INA129 die with the 49.4 kΩ gain network: 5 nA of bias current, 8 nV per root hertz of noise, 120 dB of rejection at a gain of 100, 700 µA of supply current and a 1.3 MHz unity gain bandwidth that falls to 200 kHz at a gain of 100. The offset is quoted per gain, 500 µV divided by gain maximum on this bin, which is the number a buffer stage has to be measured against.

The INA129U-2K5 rows as the addendum publishes them

Part classPrecision instrumentation amplifier, three op amp, current feedback input
Vendor statusActive, production
Data sheetSBOS051G, revised January 2026
Addendum row it normalises toINA129U/2K5, 2500 pieces on a large reel
GradeU bin
Gain equationG = 1 + 49.4 kΩ divided by RG
Input offset voltage500 µV divided by gain maximum on the U bin
Offset drift0.5 µV per degree divided by gain maximum
Input bias current5 nA maximum
Voltage noise8 nV per root hertz at 1 kHz
Common mode rejection120 dB minimum at a gain of 100, 80 dB at unity gain
Bandwidth1.3 MHz at unity gain, 200 kHz at a gain of 100
SettlingQuoted against gain; the overload recovery is the row that limits a multiplexer scan
Supply rangePlus or minus 2.25 V to plus or minus 18 V
Quiescent current700 µA typical
BodySOIC, D outline, 8 pins
Carrier2500 pieces on a large reel
Moisture levelLevel 3, 260 degrees, 168 hour floor life
Temperature rangeMinus 40 to plus 125 degrees
Tube siblingINA129U, 75 pieces per tube

Tubes, reels and two different moisture levels

The SOIC rows ship 75 pieces in a tube or 2500 pieces on a large reel, and the DIP rows ship 50 pieces in a tube. The carrier decides the handling, not the part: a 75 piece tube is a prototype or a small build, and a 2500 piece reel is a production run that will take months to consume. Between those two there is nothing on the addendum, which is why a build of 500 boards is usually bought as several tubes and hand fed rather than as a partial reel.

The moisture level differs between the carriers on this family. The tube rows are published at level 2 with a one year floor life, and the reel rows at level 3 with a 168 hour floor life, so the same die has a different shop floor rule depending on how it arrived. A level 3 reel that is opened for a partial build has to go back into dry storage or be baked, and a 2500 piece reel can easily sit open across two builds. Reading the level off the label rather than off the part number is the practical control, and INA129U-2K5 is the code to check it against.

The D body at 4.9 by 6 mm against the P body at 9.8 by 9.4 mm

The family ships in two bodies, an eight pin SOIC measuring 4.9 mm by 6 mm and an eight pin plastic DIP measuring 9.81 mm by 9.43 mm, and the difference is a process decision rather than an electrical one. The D body runs on the reflow line with the rest of the board and is the default for a new build; the P body needs plated through holes, a separate insertion step and either wave or selective solder, and on a board with a handful of DIP parts that second process usually costs more than the part.

The reason to keep the P body is mechanical. A socketed DIP can be replaced in the field or swapped during calibration without a rework station, and the longer leads absorb a mismatch between the board and a connector. A probe amplifier that is trimmed on the bench is a genuine case for the socket. On INA129U-2K5 the die and the pinout are the same in both bodies, so a board can move from one to the other without an electrical change, and the footprint is the only thing that has to be revisited.

Gain error rows, the A grade and the 0.024 per cent window

Gain error on this family is quoted per gain setting and per grade, and the tightest row is 0.024 per cent at a gain of 1 on the A grade parts. That figure is smaller than the tolerance of the resistor that sets the gain, so the resistor, not the amplifier, is what a calibration adjusts. At a gain of 100 the family rows widen and the A grade still holds a window about half as wide as the plain grade, which is the practical difference between the two bins on a channel that is calibrated once rather than per unit.

Nonlinearity is 0.001 per cent of full scale on the plain grade and 0.0005 per cent on the A grade, which is well below any converter this part is likely to drive. The number that limits a real channel is the gain drift, quoted in ppm per degree, because it cannot be trimmed at the bench and it moves with the cabinet temperature. On INA129U-2K5 the drift row is the one to put in a specification that has to hold over temperature, and the room temperature gain error row is the one to put in a production test limit.

Why the INA129 uses 49.4 kΩ and the INA128 uses 50 kΩ

The two parts in this document are the same silicon with one difference in the internal gain network: the INA128 uses 50 kΩ so that G = 1 + 50 kΩ divided by RG, and the INA129 uses 49.4 kΩ so that G = 1 + 49.4 kΩ divided by RG. The 49.4 kΩ is there so that a resistor value chosen for a competing part gives the same gain in the INA129, which is what makes it a drop-in replacement on an existing board without a resistor change. On a gain of 100 the difference between the two equations is 1.2 per cent, which is larger than the resistor tolerance and large enough to fail a calibrated channel.

Because of that, INA129U-2K5 must be bought as the part the board was drawn for, and the substitution question is not symmetrical. An INA129 in an INA128 socket runs 1.2 per cent low at a gain of 100 and 0.12 per cent low at a gain of 10, so it passes a functional test and fails a calibration. An INA128 in an INA129 socket runs high by the same amount. Neither failure is visible without a gain measurement, which is why the two codes should never be treated as interchangeable.

Settling time against gain on a multiplexed front end

The settling time curve on this family is the one to read before a channel is put behind a multiplexer. At a gain of 100 the part settles to 0.01 per cent in a few microseconds, which allows a scan rate in the tens of kilohertz; at a gain of 1000 the same figure stretches out and the scan rate falls with it. The stage before the converter has to settle from the previous channel's value, not from zero, so the worst case is a full scale step between two adjacent channels, and that is the step the vendor curve uses.

The other half of the settling budget is the multiplexer and the filter between it and the amplifier. A 1 kΩ series resistor with a 100 nF capacitor has a 100 µs time constant, which dominates the amplifier completely and is the usual reason a scan runs slower than the data sheet suggests. On INA129U-2K5 the settling figure is only useful when the input network in front of it is faster than the amplifier, and a channel that ignores that rule will show an inter-channel error that moves with the source impedance.

Plus or minus 40 V of input protection and the bias current return path

The inputs survive 40 V beyond the rails without damage, which covers the ordinary fault of a transducer cable being plugged in while the rack is powered, and it covers a miswired bridge. It does not cover a sustained fault at the supply pin, and it does not protect the source: a 40 V fault drives current through the protection network and into whatever is driving the amplifier, so a series resistor at the connector is still worth the board space. The protection also stops being transparent above roughly a megohm of source resistance.

The bias current return path is the second half of the input requirement. Each input needs a dc path to a defined potential, and a floating source such as a transformer or a capacitive sensor will let the inputs drift until the amplifier saturates. The vendor shows the ordinary arrangements, and the one to avoid on INA129U-2K5 is a path through a high value resistor on one leg only, because that converts the bias current into a differential offset. Matched paths on both legs, or a path to the reference rather than to ground, keep the error common mode.

Buying INA129U-2K5

A hyphen in the middle of a part number is the kind of detail that turns into a line stop, because an ERP system that treats INA129U-2K5 and INA129U/2K5 as two items will hold two safety stocks for one part and still run short. The clean approach is to map both spellings to the addendum row in the item master and to buy against that row. Our BOM scrubbing page describes the check we run on a customer file for exactly this class of duplicate.

The quantities are the same on both spellings, so there is no pricing difference to chase. The one thing to confirm is the moisture level, because the reel rows in this family are split between level 3 and level 2 depending on the G4 suffix, and a substituted G4 reel changes the floor life on the line without changing the part.

Questions that arrive with this part number

Whether the hyphen changes the part is the first question, and it does not: both spellings normalise to INA129U/2K5 at 2500 pieces on a large reel. Whether the reel and the tube are interchangeable is the second, and they are, at the same grade and the same silicon, with the carrier and the moisture level as the only differences.

The third is what to do when the supplier confirms only the hyphen spelling against a customer drawing that carries the slash. The answer is a deviation note on the drawing rather than a new part number, because two item numbers for one reel is how a duplicate safety stock gets created and how a shortage gets missed.