Contact Us

INA121U

Brand: Texas Instruments
Texas Instruments INA121U is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA121U — Power Management & Signal Chain | Superb Automation

INA121U

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA121U from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA121U: the FET input amplifier in an SO-8 body for a reflow line

The INA121U is the surface mount member of this family, in the eight pin SO-8 body with the same die, the same pinout and the same electrical rows as the plastic DIP. The reason to choose it is process rather than performance: a reflow line does not want a through hole part, and a board that carries one DIP needs a second soldering process, a second inspection step and a second set of handling rules for a part that is otherwise identical to the one next to it on the reel.

The carrier for this row is a 75 piece tube. That is the detail that catches people out: the SO-8 body in the tube is a surface mount part in a through hole carrier, which is fine for a prototype and awkward for a line. The same body is also sold on a 2500 piece reel under the /2K5 suffix, and the reel is the carrier a production line should be specifying.

The INA121U rows as the addendum publishes them

Part classFET input instrumentation amplifier, current feedback
Vendor statusACTIVE, production data
Data sheetSBOS078
Gain equationG = 1 + 50 kΩ divided by RG
Input offset voltagePlus or minus 200 µV
Offset driftPlus or minus 2 µV per degree
Input bias currentPlus or minus 4 pA
Common mode rejection106 dB
Quiescent current450 µA
Supply rangePlus or minus 2.25 V to plus or minus 18 V
BodySOIC, D outline, 8 pins
Carrier for this row75 pieces per tube
Reel siblingINA121U/2K5, 2500 pieces on a large reel
Grade siblingINA121UA, same body tighter offset bin
Moisture levelLevel 3, 260 degrees, 168 hour floor life
Temperature rangeMinus 40 to plus 85 degrees
Lead finishPublished as call TI
RoHSYes on the addendum row

The moisture level 3 row applies to the tube as much as the reel, and it is the row that a small build forgets. A tube opened for ten pieces and left on the bench for a week is out of its floor life, and the reflow profile that was qualified on a fresh part will show popcorning on the stored one. Dry storage or a bake before use is the answer, and the bake is a process step with a cost that should be in the build estimate rather than discovered at the reflow oven.

Same die in a different body, and what that does to the footprint

The SO-8 body has the same eight pin function assignment as the DIP, so a circuit can move between them without a circuit change, but the footprint and the thermal path are different. The SO-8 has a lower thermal resistance to the board and a shorter lead, which matters at 450 µA of supply current not at all and matters for the input leakage because the shorter lead is less of an antenna. On a high impedance input the smaller body is a small advantage.

The pin pitch is the practical constraint. A 1.27 mm pitch is easy for a reflow line and hard for hand rework, and a channel that will be trimmed at the bench needs the trim resistor to be reachable. Placing the gain resistor on the same side as the amplifier and within a few millimetres of the RG pins keeps the loop small, and it also keeps the trim access from needing a second rework pass on the other side of the board.

The gain resistor is the part that decides the accuracy

The amplifier is trimmed to 200 µV and the gain resistor is not trimmed at all. At a gain of 100 the resistor is about 505 Ω, and a 1 per cent resistor gives 1 per cent of gain error, which is five times the amplifier's own contribution on a 10 mV signal. A 0.1 per cent resistor with a 25 ppm per degree temperature coefficient costs a few cents and removes the term. The resistor value also sets the bandwidth: a smaller resistor means a higher gain and a narrower bandwidth, and the vendor curve at the chosen gain is the reference for whether the channel still settles in time.

Two resistors in series are sometimes used to hit a non standard gain, and that is fine as long as the pair is treated as one component for drift. A 0.1 per cent and a 1 per cent resistor in series gives a value that is dominated by the worse of the two over temperature, and the resulting drift shows up as a gain error that moves with the cabinet temperature rather than with the signal.

Where the SO-8 body belongs

Any board that is reflowed and carries more than one of these amplifiers should use the SO-8 body, because the process saving is per board rather than per part. A multi channel instrument with eight input channels on one card is the obvious case: eight SO-8 parts in one reflow pass against eight DIP sockets and a selective solder step. The same card in the DIP body is a prototype, not a product.

The DIP body still belongs in two places: a socketed calibration fixture, and a board that was laid out a decade ago and is being built again with the original footprint. In both cases the part is being used for its electrical behaviour and the package is a constraint that cannot be changed. Changing a qualified board to save a process step is a requalification, and requalification costs more than the process step unless the volume is large.

Buying INA121U

The tube row is active and the reel sibling is active, so the buy is a choice of carrier rather than of availability. A purchase order that names the tube for a production build is a purchase order that has not read the carrier column, and the correction is a phone call to the distributor rather than a line stop, provided it happens before the build. After the build it is a rework.

The grade is the other decision. The U row is the plain bin and the UA row is the tighter bin in the same body. Since the two are pin compatible and the same price band, a channel with a marginal offset budget should take the UA and a channel with margin should take the U. Our pin to pin cross reference page lists the grades and bodies we can swap within a family, and the incoming inspection plan page describes the checks we run on a mixed shipment.

Receiving a tube of SO-8 parts

A tube of surface mount parts is the carrier that most often arrives without a moisture indicator, because the tube is not sealed with desiccant in the way a reel is. The inspection that matters is therefore the label and the date code rather than the seal: the date code tells how long the parts have been in the channel, and a tube that was bagged two years ago has a solderability question that a fresh tube does not. Photographing the label at receiving costs a minute and settles the question later.

The second check is the pin one orientation. A tube of eight pin parts can be loaded either way, and a tube that has been re-packed by a distributor is the case where the orientation is no longer the vendor's. A visual check on the first few parts costs nothing and catches the one tube in a hundred that would place a whole board rotated.

Questions that arrive with this part number

Whether the tube and the reel are the same part is the first question, and they are: same body, same die, same grade, different carrier. Whether the part can be reflowed twice is the second, and the level 3 rating allows it if the floor life is respected between passes; a second pass on a part that has been out of dry storage is the classic popcorn failure. The third question is the finish, which is published as call TI, so the solderability should be checked on the first article rather than assumed.

The fourth question is whether the SO-8 body is drop in for the DIP on an existing board. It is not: the footprint differs, and a socketed DIP cannot be replaced by a surface mount part without a board revision. The electrical equivalence is real and the mechanical equivalence is not.