Contact Us

INA106KP

Brand: Texas Instruments
Texas Instruments INA106KP is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA106KP — Power Management & Signal Chain | Superb Automation

INA106KP

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA106KP from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA106KP: a fixed gain of ten in an eight pin DIP

The INA106KP is a monolithic differential amplifier with a fixed gain of ten, built from one precision op amp and four laser trimmed metal film resistors on the die. It sits in an eight pin plastic DIP, published ACTIVE in a 50 piece tube, and it exists to do one job: subtract one voltage from another and multiply the difference by ten, with a common mode rejection of 86 dB minimum and a gain error under 0.025 per cent. A discrete difference amplifier with four resistors cannot match that, because the matching of the four resistors is what sets the rejection and 0.01 per cent matching is expensive to buy as parts.

The applications in the vendor document are all current or voltage sensing in a noisy environment: battery cell formation equipment, servo drive position feedback, level transmitters, string inverters, data loggers. In each case the signal of interest is a small difference sitting on a large common mode, and the gain of ten brings it up to a range where a converter can read it.

The INA106KP rows as the addendum publishes them

Part classFixed gain differential amplifier
Vendor statusACTIVE, production data
Data sheetSBOS152C, August 1987, revised December 2025
Gain10, fixed by on chip resistors
Input offset50 µV typical, 200 µV maximum
Offset drift0.2 µV per degree typical
Common mode rejection86 dB minimum, 100 dB typical
Gain error0.01 per cent typical, 0.025 per cent maximum
Gain drift4 ppm per degree typical
Nonlinearity0.0002 per cent typical, 0.001 per cent maximum
Power supply rejection1 µV per volt typical, 10 µV per volt maximum
Differential input impedance10 kΩ
Common mode input impedance110 kΩ
Common mode input rangePlus or minus 11 V
Differential input rangePlus or minus 1 V
Bandwidth0.5 MHz at 3 dB
Full power bandwidth300 kHz typical at 20 V peak to peak
Slew rate2 V per microsecond typical, 20 on the other chip site
Settling to 0.1 per cent5 µs
Settling to 0.01 per cent10 µs
OutputPlus or minus 10 V at 5 mA, 20 mA available
Capacitive load1000 pF stable
Noise at 10 kHz30 nV per root hertz on one chip site, 20 on the other
Quiescent current1.5 mA typical, 2 mA maximum
Supply rangePlus or minus 6 V to plus or minus 18 V
BodyPDIP, 8 pins, 9.81 by 9.43 millimetres
Tube rowINA106KP, 50 pieces, tube, Active
MarkingIN106P or INA106KP, both published
Temperature rangeMinus 40 to plus 85 degrees

The marking row is unusual: the vendor publishes two acceptable markings, IN106P and INA106KP, on the same orderable row. A first article inspection that expects one of them and finds the other will raise a discrepancy that is not one, and the invoice string is what should be checked rather than the top of the package.

The 10 kΩ input and the source it expects

The differential input is 10 kΩ because the resistors are on the die rather than buffered. That means the source sees a real load, and any source resistance adds a gain error: a 100 Ω source in series with the 10 kΩ input changes the gain by 1 per cent, which is forty times the gain error of the part itself. The usual fix is a unity gain buffer on each input, and at that point the question becomes whether a three op amp instrumentation amplifier would have been simpler.

Where the source impedance is low, such as a shunt resistor or a current sense transformer secondary, the part is ideal and the buffer is unnecessary. That is why battery test equipment and servo current sense appear in the application list: the source there is a fraction of an ohm.

Common mode range and the supply

The common mode range is plus or minus 11 V on a plus or minus 15 V supply, so the inputs can sit close to the rails but not at them. A high side current sense on a 48 V rail is outside that window and needs a different part with a much wider common mode range, which this family does not offer. A low side sense, where the common mode is near ground, is inside the window with plenty of margin.

The supply range of plus or minus 6 to 18 V covers the usual 12 and 15 V analogue rails. The quiescent current of 1.5 mA is modest, and because the part is a single amplifier rather than three, it dissipates far less than the instrumentation amplifiers in this family, which matters on a board with eight current sense channels.

Noise and the chip site note

Two noise figures appear in the data sheet, 30 and 20 nV per root hertz, because the part is built at two chip sites with slightly different resistor geometries. The vendor labels them SHE and RFB in the tables rather than hiding the difference, and a customer matching a specification should use the worse of the two unless the site is fixed at purchase. For a 20 mV signal over a 100 kHz bandwidth, 30 nV per root hertz is about 9.5 µV rms, which is 0.05 per cent of full scale.

The slew rate differs by a factor of ten between the sites, which is the larger practical difference. A 20 V step with a 2 V per microsecond slew takes 10 µs, and with 20 V per microsecond it takes 1 µs. For a multiplexed system that settling difference decides the scan rate, so the site question is worth asking when the part is specified into a fast scanner.

Buying INA106KP

A single tube row of 50 pieces, no reel, at industrial temperature. The through hole body is kept for the same reasons as the rest of this family: sockets, repairs and small builds. A production line uses the surface mount row, which is on a reel of 2500.

Because the part is old and the die is simple, the availability risk is low, but the two chip sites mean that two shipments can have different noise and slew characteristics. A customer with a tight settling budget should specify a site or accept the worse number.

Questions that arrive with this part number

Whether the gain can be changed is the first, and it cannot, because the resistors are inside. A gain of 0.1 or of 100 is a different part number. The second is whether the part can measure a current on the high side of a 24 V rail. It cannot, because the common mode range stops at 11 V, and the answer is a dedicated current sense amplifier.

The third is whether the reference pin allows the output to be offset. It does, and that is how a bipolar input is shifted into a single ended converter's range. The reference source impedance has to be low, because it appears in the gain path for the common mode signal.

The chip site question is worth asking at the quotation stage rather than at the first article. Two sites with different resistor geometries produce two noise and slew figures, and a customer who has qualified a scanner at the faster site will see a slower settling time if the next delivery comes from the other. Naming the site in the purchase order is the only way to hold the faster figure.

A last point on the order: the tube of 50 carries no moisture limit and no bake requirement, which makes it the simplest carrier in this family for a repair operation that opens a tube once a month.

For a build that is comparing this part with a three op amp instrumentation amplifier, the amplifier cross reference page lists the family, and the pin to pin page covers the footprint differences.