INA103KP
Product Specifications
INA103KP
Texas Instruments — Power Management & Signal Chain
Product Overview
The INA103KP from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
INA103KP: the low noise instrumentation amplifier for audio and bridge signals
The INA103KP is a current feedback instrumentation amplifier with 1 nV per root hertz of input noise, 0.0009 per cent total harmonic distortion at a gain of 100, and a 6 MHz bandwidth at unity gain. It sits in a 16 pin plastic DIP, published ACTIVE in a 25 piece tube, and it is the part a customer specifies when the signal is small and the noise floor matters more than the offset. A dynamic microphone, a moving coil pickup, a strain gauge bridge and a differential receiver all appear in the vendor's application list for this device.
The current feedback topology is what gives it the bandwidth. A conventional three op amp instrumentation amplifier loses bandwidth as gain rises, because the gain is set by a feedback network around a fixed gain stage. This part uses a different arrangement in which the gain resistor sets the transconductance directly, so the 3 dB bandwidth at a gain of 100 is still 800 kHz, and the distortion stays low because the internal cancellation circuit removes the error that a simple current feedback stage would leave.
The INA103KP rows as the addendum publishes them
| Part class | Low noise instrumentation amplifier, current feedback |
| Vendor status | ACTIVE, production data |
| Data sheet | SBOS003A, Burr-Brown PDS-1016I, revised September 2023 |
| Gain range | 1 to 1000 |
| Gain equation | G equals 1 plus 6 kΩ divided by RG |
| Built in gains | 1 and 100 by pin strapping, others with an external resistor |
| Input noise at 1 kHz | 1 nV per root hertz |
| Input noise at 10 Hz | 2 nV per root hertz |
| Total harmonic distortion | 0.0009 per cent at 1 kHz and a gain of 100 |
| Initial offset | 30 µV plus 1200 µV divided by G, typical |
| Offset drift | 1 µV per degree plus 20 µV per degree divided by G |
| Common mode rejection, G equals 100 | 100 dB minimum, 125 dB typical |
| Common mode range | Plus or minus 11 V linear, 12 V typical |
| Input impedance, differential | 60 Ω in parallel with 2 MΩ and 2 pF |
| Bandwidth at G equals 1 | 6 MHz |
| Bandwidth at G equals 100 | 800 kHz |
| Slew rate | 15 V per microsecond |
| Settling to 0.1 per cent, G equals 100 | 1.5 µs |
| Output into 600 Ω | Plus or minus 11.5 V, 40 mA |
| Capacitive load | 10 nF stable |
| Supply range | Plus or minus 9 V to plus or minus 25 V |
| Quiescent current | 9 mA typical, 12.5 mA maximum |
| Body | PDIP, 16 pins |
| Tube row | INA103KP, 25 pieces, tube, Active |
| Temperature, specified | 0 to plus 70 degrees |
| Temperature, operating | Minus 40 to plus 85 degrees |
Two rows set this part apart from the rest of the family. The 1 nV noise density is the lowest of any instrumentation amplifier in this group, and it is quoted at 1 kHz rather than at DC, so it is a real audio band figure. The 15 V per microsecond slew rate at a 100 gain gives a full power bandwidth of about 240 kHz into a 10 V output, which is enough for audio and for a fast bridge excitation scheme.
The 60 Ω differential input impedance and what it means
This is not a high impedance input. The differential impedance is 60 Ω in series with 2 MΩ, which is the resistance of the internal gain network rather than a buffered input. A source with a 200 Ω output impedance therefore forms a divider with the input and loses about a quarter of its signal, and the gain equation no longer describes the transfer function on its own.
That is the trade this part makes for its noise performance, and it is why the vendor describes it as being for 200 Ω sources. A microphone with a 200 Ω output is a perfect match; a pH electrode with a 100 MΩ source is the wrong sensor for this amplifier at any gain. The INA101 and INA110 in this family have the high impedance input, and choosing between them is a source impedance question before it is a noise question.
Distortion and the audio application
The 0.0009 per cent figure at a gain of 100 and 1 kHz is what allows this part to replace a transformer in a microphone preamplifier. A transformer has no distortion figure worth quoting at low level but it has a low frequency limit, a size, a cost and a magnetic pickup problem, and the amplifier has none of those. The distortion cancellation circuit is the reason: without it, a current feedback stage at a gain of 100 would produce harmonics an order of magnitude higher.
At a gain of 1000 the distortion rises because the internal loop gain falls, and the data sheet's figure is quoted at 100 for that reason. A customer who needs 60 dB of gain in one stage should check the curve at that gain rather than assume the headline applies.
Supply, decoupling and the reference pin
The supply range of 9 to 25 V per rail is wider than the rest of the family, which suits a system with a 15 V analogue rail. The reference pin sets the output offset, so a bipolar signal can be shifted to sit inside a single ended converter's input range without an external level shifter. The reference pin should be driven from a low impedance source, because any resistance there appears as a gain error on the common mode signal.
Decoupling is conventional: 0.1 µF close to each supply pin and a 10 µF bulk capacitor within a centimetre. At 6 MHz of bandwidth the part draws current in short bursts, and a supply that is not decoupled will show the burst as a ripple on the output through the finite supply rejection.
Buying INA103KP
One live carrier, a 25 piece tube, with no reel row for the plastic DIP. A production build of any size therefore uses the surface mount part in the sibling row, and the DIP is kept for prototypes, repairs and sockets. That is a common pattern for a through hole analogue part at this age of its life.
The specified temperature range is 0 to 70 degrees, which is a commercial grade rather than an industrial one. A customer who needs minus 40 to 85 has to accept that only part of the specification is guaranteed outside 0 to 70, even though the part will operate there.
Questions that arrive with this part number
Whether this amplifier can be used with a high impedance sensor is the first, and the answer is no above about 10 kΩ of source impedance, because the 60 Ω input loads the source. The second is whether the built in gain of 100 can be used without any external part. It can, by strapping the gain pins, and that removes the gain resistor tolerance from the error budget entirely.
The third is whether the part is stable with a capacitive load. It is stable to 10 nF, which is unusually generous, so a cable or a filter capacitor at the output does not need a series resistor up to that value.
The reference pin closes the loop on offset. Driving it from a low impedance source shifts the output without touching the input, and a 10 Ω series resistance there adds 10 Ω to the gain network, which at a gain of 1000 is a measurable error on a 10 mV signal. A buffer or a resistor divider with a capacitor is the right way to set it.
It should be driven from the same reference the converter uses, so that the two drift together and the ratio stays fixed across temperature.
For a programme that is choosing between the low noise and the high impedance members of the family, the amplifier cross reference page lists them side by side, and the drop in verification page covers the source impedance check.