Contact Us

INA101KU

Brand: Texas Instruments
Texas Instruments INA101KU is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA101KU — Power Management & Signal Chain | Superb Automation

INA101KU

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA101KU from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA101KU: the same amplifier in a 16 pin surface mount body

The INA101KU is the surface mount member of the INA101 family, in a 16 pin SOIC, published ACTIVE in a 40 piece tube and a 1000 piece reel. Electrically it is the same three op amp instrumentation amplifier as the plastic DIP part: gain from 1 to 1000 set by one resistor, 10^10 Ω differential input impedance, 100 dB of common mode rejection at a gain of 100, and the same 13 nV per root hertz of input noise. What changes is the package, the thermal path and the carrier.

The surface mount body is wider than the DIP in pin count but not in function, and the extra pins are the gain sense and gain set connections that the DIP brings out on its own pins. That difference matters when a board is converted from through hole to surface mount: the gain resistor moves from two pins to four, and the two sense lines have to be routed as a pair back to the resistor.

The INA101KU rows as the addendum publishes them

Part classInstrumentation amplifier, surface mount body
Vendor statusACTIVE, production data
Data sheetSBOS133, Burr-Brown PDS-454K, July 1998
Gain range1 to 1000, one external resistor
Gain equationG equals 1 plus 40 kΩ divided by RG
Initial offset125 µV plus 450 µV divided by G, typical
Offset drift2 µV per degree plus 20 µV per degree divided by G
Common mode rejection, G equals 100100 dB minimum, 105 dB typical
Input bias current, ceramic grades15 nA typical, 30 nA maximum
Input noise at 1 kHz13 nV per root hertz
Bandwidth at G equals 10140 kHz
Bandwidth at G equals 10025 kHz
Slew rate0.4 V per microsecond typical
Output current5 mA rated, 10 mA available
Supply rangePlus or minus 5 V to plus or minus 20 V
Quiescent current6.7 mA typical, 8.5 mA maximum
BodySOIC, 16 pins, wide body
Tube rowINA101KU, 40 pieces, tube, Active
Reel rowINA101KU/1K, 1000 pieces, large tape and reel, Active
Moisture levelLevel 3 at 260 degrees, 168 hours floor life
MarkingINA101KU
Temperature, specifiedMinus 25 to plus 85 degrees
Temperature, operatingMinus 55 to plus 125 degrees

The reel suffix is worth reading twice. The full string is INA101KU/1K, where the 1K is the quantity and not a grade, and a purchase order that drops it will not match the vendor row. The tube at 40 pieces and the reel at 1000 are both live, so a prototype can be built without opening a reel.

The four pin gain connection

In the surface mount body the gain resistor connects between the two gain set pins, and the two gain sense pins go back to the amplifier's internal summing nodes. The sense pair carries almost no current, so it can be a thin trace, but it has to be a pair: routing one sense line and letting the other take a different path turns the trace inductance into a gain error at high frequency, and the effect appears as a peak in the frequency response rather than as a DC error.

The resistor itself should sit within a few millimetres of the pins. At a gain of 1000 the resistor is 40 Ω, and 10 millimetres of 0.2 millimetre trace adds about 0.02 Ω, which is 0.05 per cent of the gain. That is small but not zero, and at a gain of 1000 every 0.05 per cent counts against a 0.1 per cent budget.

Thermal behaviour of the surface mount body

The wide SOIC body has a larger lead frame than the DIP and a shorter thermal path to the board, so the junction runs cooler for the same dissipation. At 8.5 mA of quiescent current and a 30 V total supply the part dissipates a quarter of a watt, and the body temperature rise is modest. The limit is reached when the output drives a heavy load: 10 mA into a 1 kΩ load is another 10 mW in the output stage, which is still small, but 10 mA into a 50 Ω cable is 5 mW of cable loss plus the output stage loss, and the sum is what matters.

Because the offset drift is 2 µV per degree, a 30 degree rise in the package from self heating appears as 60 µV of input offset. On a 10 mV signal that is 0.6 per cent, which is larger than any other error in the chain. Keeping the dissipation low is therefore part of the accuracy budget, not just a reliability question.

Where the surface mount row is the right choice

Any board that is assembled on a reflow line wants this row rather than the DIP, because a through hole part needs a second process and a hand or wave solder step. The 1000 piece reel at level 3 is a normal production carrier and the 40 piece tube covers the prototype. The pin count is higher but the board area is smaller than the DIP footprint including its drilled holes.

For a mixed signal board where the amplifier sits next to a converter, the surface mount body also allows the input traces to be short and guarded, which is harder with a through hole part that has to be placed where the drill pattern fits.

Buying INA101KU

Two live carriers, 40 in a tube and 1000 on a reel, both at level 3. A production run of a few hundred boards consumes a reel in a year, and the tube covers the engineering build. The NOPB question does not arise here because the family predates the lead free suffixes, and the addendum shows a nickel palladium gold finish rather than tin lead.

Because the part is a Burr-Brown part now sold by a larger vendor, the availability risk is the same as any long lived analogue part: the die is old, the wafer fab is old, and a discontinuation notice is always possible. A customer with a ten year product should hold a last time buy sized on the service tail rather than on the build forecast.

Questions that arrive with this part number

Whether this part is a drop in replacement for the DIP version is the first question, and it is not, because the pin out differs and the gain connections move. The second is whether the surface mount body has the same offset grade as the DIP. It does, and both are the plastic grade rather than the ceramic one, so the 125 µV figure applies to both.

The third is whether the part can run from a single 5 V supply. It cannot, because the output swing and the input range are both referenced to the midpoint of a split supply, and a single supply version would need a rail splitter and a different input common mode. That is a different part number in the same family rather than a configuration of this one.

The offset null pins are a real advantage of this package. With a 250 µV maximum offset and a 2 µV per degree drift, a one point trim at room temperature brings the offset inside 25 µV, and the residual drift then contributes 60 µV over a 30 degree excursion. That is a factor of two better than the untrimmed part and it costs one potentiometer or one pair of resistors selected at test.

A last point on the carrier: the 40 piece tube is enough for a pilot build of a few boards, and the 1000 piece reel is the production route, so a programme can move between the two without a part number change.

For a board that is converting from through hole to surface mount, the amplifier cross reference page lists the family rows, and the pin to pin page explains what has to be checked when the pin count changes.