DRV8886ATRHRR
Product Specifications
DRV8886ATRHRR
Texas Instruments — Power Management & Signal Chain
Product Overview
The DRV8886ATRHRR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
DRV8886ATRHRR: the 28-pin QFN body of the 2 A stepper driver
The DRV8886ATRHRR is the 28-pin WQFN body of the DRV8886AT, at 5.50 mm by 3.50 mm and 19.25 mm squared. The circuit is the same 8 V to 37 V bipolar stepper driver with 2 A full scale and 1.4 A rms per bridge, integrated current sense at plus or minus 6.25 percent, 1/16 microstepping and smart tune decay. What differs from the HTSSOP version is the footprint and the thermal path: 19.25 mm squared of pad against 49.92, in a body that is 2.3 mm shorter in one direction.
The smaller pad is the engineering decision. At 1.4 A rms and 550 mOhm the two phases dissipate about 2.2 W, and the QFN removes that heat through the exposed pad into the copper under it. A four layer board with a solid plane and a via grid handles it; a two layer board with a thin trace under the pad does not, and the difference shows up as a driver that works on the bench and reaches thermal shutdown inside the enclosure.
The interface and the configuration are pin strapped: STEP and DIR for motion, pins for the step mode and the decay mode, and an nFAULT output. There is no serial port, so nothing has to be loaded at power up and the start sequence is a matter of enabling the part and sending pulses. Sleep current is 20 microamps, and the logic inputs accept the usual 3.3 V and 5 V controller levels.
Microstepping to 1/16 covers the mechanisms that were built around this generation of driver: printers, scanners, vending elevators, syringe pumps and sample stages that need smooth motion at moderate speed. A mechanism that needs 1/256, stall detection or a serial register map moves to the 48 V or 65 V family, and that move brings a different pin count and a different body.
Key data for the DRV8886ATRHRR
| Operating supply | 8 V to 37 V, absolute maximum 40 V |
| Current | 2 A full scale, 1.4 A rms, 3 A peak per bridge |
| On resistance | 550 mOhm high side plus low side at 24 V and 25 C |
| Microstepping | Up to 1/16, non circular and standard half step modes included |
| Current sense | Internal, plus or minus 6.25 percent full scale, no sense resistors |
| Decay | Smart tune, slow and mixed, dynamic or fixed off time |
| Sleep current | 20 microamps typical |
| Protection | Undervoltage, charge pump undervoltage, overcurrent, thermal shutdown, nFAULT |
| Temperature | Minus 40 C to plus 125 C operating |
Body, packing and marking data
| Body in this code | 28-pin WQFN, the RHR outline, 5.50 mm by 3.50 mm, 19.25 mm squared with an exposed pad |
| Other body | 24-pin HTSSOP, the PWP outline, 7.80 mm by 6.40 mm, 49.92 mm squared with a PowerPAD |
| Carrier | Tape and reel; the count per reel is read from the vendor addendum row for this order code |
Reading the code before you buy it
DRV8886AT is the circuit, RHR is the 28-pin WQFN and the trailing R is the reel. The pin count differs between the two bodies, so this is not a same footprint pair: the QFN carries the same functions on more, smaller pads. A board change between them is new copper, and a sourcing decision that treats them as one part number is the kind of error that reaches the assembly line.
The T in the circuit name marks the internal current sense and the smart tune decay, and the earlier DRV8886 without the T used a different current scheme. The two are not interchangeable in a drawing even where the pin count matches, because the current reference is set differently and the decay behaviour differs at low speed.
On availability, this generation of driver is being superseded in new projects by the 48 V and 65 V family with the serial port, but it remains in production and it remains in the installed base of printers and vending machines that are still being built. That installed base is where a sourcing desk earns its money: the part is not on a last time buy notice, and the board cannot take a newer driver without new copper. Our component obsolescence management page is where we track that exposure.
Where the DRV8886ATRHRR fits
Compact printers and label makers use the QFN body because the board is small and the driver sits close to the motor under a shield. Portable instruments and handheld analysers use it where the 19 mm squared pad fits behind the mechanism and the 24 V rail is available from a pack or an adapter.
Vending machines, kiosks and locker systems use it for the elevator and the dispenser, where the board is behind a panel and the ambient can reach 50 C. The 125 C junction rating and the 37 V supply ceiling are what make that practical, and the QFN pad has to be soldered to a copper area that was sized for the loss rather than for the footprint.
Where it does not fit is a board that cannot give the pad a copper plane, or a mechanism that needs finer than 1/16 microstepping. In the first case the HTSSOP body is the answer, in the second a newer driver. Our PCBA quote checklist page lists the thermal and the microstepping questions we ask before quoting either.
Questions we get on this code
Is the QFN body rated for the same current as the HTSSOP? The silicon is the same and the pad is smaller, so the current rating holds only where the copper under the pad holds the temperature rise down. The vendor quotes the current at 25 C with a good board, and the enclosure temperature is the number that changes it.
Can the part be reworked? A 5.5 mm by 3.5 mm QFN can be removed and replaced with hot air and a stencil, and the pad has to be cleaned and re-pasted. It is a normal rework step for a contract assembly house, and it is not a bench job with an iron.
What sets the current limit? The internal sense and the indexer setting, with the full scale current adjusted by the reference pins rather than by a resistor. The plus or minus 6.25 percent figure applies across that range, so a 1 A setting can land between 0.94 A and 1.06 A.
Why choose this over the 48 V part? Cost, size and simplicity. The 48 V part is a 16-pin body with a serial port and finer microstepping; this one is a 28-pin body with no bus and 1/16 stepping. A 24 V printer does not need the extra function, and a 48 V machine cannot use this part at all.