DRV8886ATPWPR
Product Specifications
DRV8886ATPWPR
Texas Instruments — Power Management & Signal Chain
Product Overview
The DRV8886ATPWPR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
DRV8886ATPWPR: 2 A stepper drive with smart tune in a 24-pin body
The DRV8886ATPWPR is the 24-pin HTSSOP body of the DRV8886AT, a bipolar stepper driver rated 8 V to 37 V and 2 A full scale per bridge. It carries two H-bridges, a microstepping indexer that runs to 1/16, and integrated current sensing with plus or minus 6.25 percent full scale accuracy, so the external sense resistors are not needed. The interface is STEP and DIR with pin strapped configuration, which is the shortest path from a controller to a moving motor.
The current figures are 3 A peak, 2 A full scale and 1.4 A rms per bridge, and the on resistance is 550 mOhm high side plus low side at 24 V and 25 C. At 1.4 A rms the conduction loss across both phases is about 2.2 W, so the 49.92 mm squared pad on the HTSSOP is doing real work and the copper under it is part of the specification rather than a cosmetic detail.
Decay control offers smart tune, slow and mixed, and the smart tune scheme adjusts the decay time to the motor instead of holding it fixed, which is what keeps a stepper quiet at low speed and cool at standstill. Off time is selectable between dynamic and fixed modes. Sleep current is 20 microamps, which is higher than the newer members of the family and fine for a mains powered machine.
The microstepping ceiling of 1/16 is the main limitation against the newer parts. A mechanism that needs 1/256 or a smooth low speed motion needs the 48 V or 65 V family, and a mechanism that runs at full, half, quarter or 1/16 step at 2 A is exactly what this part covers. Protection includes undervoltage, charge pump undervoltage, overcurrent, thermal shutdown and an nFAULT output.
Key data for the DRV8886ATPWPR
| Operating supply | 8 V to 37 V, absolute maximum 40 V |
| Current | 2 A full scale, 1.4 A rms, 3 A peak per bridge |
| On resistance | 550 mOhm high side plus low side at 24 V and 25 C |
| Microstepping | Up to 1/16, with non circular and standard half step modes |
| Current sense | Internal, plus or minus 6.25 percent full scale, no sense resistors |
| Decay | Smart tune, slow and mixed, dynamic or fixed off time |
| Interface | STEP and DIR with pin strapped configuration |
| Sleep current | 20 microamps typical |
| Protection | Undervoltage, charge pump undervoltage, overcurrent, thermal shutdown, nFAULT |
| Temperature | Minus 40 C to plus 125 C operating |
Body, packing and marking data
| Body in this code | 24-pin HTSSOP, the PWP outline, 7.80 mm by 6.40 mm, 49.92 mm squared with a PowerPAD |
| Other body | 28-pin WQFN, the RHR outline, 5.50 mm by 3.50 mm, 19.25 mm squared |
| Carrier | Tape and reel; the count per reel is read from the vendor addendum row for this order code |
Reading the code before you buy it
DRV8886AT is the circuit, PWP is the 24-pin HTSSOP and the trailing R is the reel. The T at the end of the circuit name marks the version with the internal current sense and the smart tune decay, so a drawing that says DRV8886A without the T describes an earlier part with a different current scheme. A reel marked DRV8886AT and a drawing marked DRV8886A are close enough to run and different enough to fail a current accuracy check.
The 24-pin and 28-pin bodies are not interchangeable, and the pin counts differ because one exposes more pins for the reference and the decay strapping. A board built for the HTSSOP at 7.8 mm by 6.4 mm cannot take the 5.5 mm by 3.5 mm QFN without new copper, so the body letter matters at the sourcing desk as well as at the assembly line.
The family position is below the 48 V and 65 V members: this part at 2 A and 1/16 microstepping, the 48 V parts at 2.5 A and 1/256 with a serial port, and the 65 V part at 3 A. A product that outgrows the 2 A rating or needs finer microstepping moves up that ladder, and the move brings a different pin count. Our pin to pin cross reference page keeps the ladder in one table.
Where the DRV8886ATPWPR fits
Printers, scanners and copiers use it for the carriage and the registration mechanism at 24 V and 1 A to 1.5 A per phase, where the 1/16 microstepping is enough for the print quality and the 37 V ceiling covers the supply transient. Vending and kiosk mechanisms use it for the product elevator, where the motor has to hold position against a load and the smart tune decay keeps the hold current from heating the motor.
Laboratory and medical instruments use it for a syringe pump or a sample stage, and there the current accuracy of plus or minus 6.25 percent is the figure that goes into the volume tolerance. Office automation and textile machinery use it where the axis count is modest and a STEP and DIR interface from the controller is simpler than a bus.
Where it does not fit is a 48 V rail, because the operating range ends at 37 V. A 48 V system that drops to this part because of a shortage is a board change with a new supply, not a substitution. Our component shortage forecast page is where we track that kind of exposure on a build.
Questions we get on this code
What is the difference between full scale and RMS here? The full scale figure is the peak of the sine wave in microstepping, the RMS figure is the heating equivalent, and the peak figure is the single pulse limit. A thermal budget uses 1.4 A rms, a current limit setting uses 2 A full scale, and the 3 A peak is only for a short transient.
Does smart tune work at standstill? The decay scheme reduces the current ripple at low speed and standstill, which is where a fixed decay produces the audible whine. It does not reduce the holding current itself; a mechanism that has to hold a load for hours needs the current reduced by the controller or by the indexer setting.
Can the 28-pin QFN body be used for the same current? Yes, the silicon is the same and the thermal pad is smaller at 19.25 mm squared against 49.92. A board with a good copper plane handles the same current in the QFN, and a board without one does not.
Why is the sleep current 20 microamps when newer parts are 2? Because the internal regulators and the charge pump on this generation keep drawing in sleep. A battery product that has to sit idle for months chooses a newer part, and a mains powered machine does not care.