DRV8845RHHR
Product Specifications
DRV8845RHHR
Texas Instruments — Power Management & Signal Chain
Product Overview
The DRV8845RHHR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
DRV8845RHHR: four H-bridges in one 6 mm package
The DRV8845RHHR is a quad H-bridge driver in a 36-pin QFN at 6.00 mm by 6.00 mm. Each of the four bridges is rated 1.5 A full scale and 2.5 A peak, the supply range is 4.5 V to 38 V operating with 40 V absolute maximum, and the on resistance is 900 mOhm high side plus low side at 24 V and 25 C. One package therefore covers two stepper motors, or four brushed DC motors, or a mix of one stepper and two brushed motors, which is exactly the mix that a printer, a vending machine or a laboratory instrument needs.
The interface is PHASE and Ixx, the industry standard parallel interface that this package shares with comparable quad drivers from other vendors. Each bridge has a two bit nonlinear digital to analog converter on its current reference, so the current is set in four steps by pin strapping rather than by a register, and a stepper driven from two bridges runs in full, half and quarter step modes. Brushed motors get forward, reverse and coast.
Decay control is smart tune only, which is the vendor's adaptive decay scheme: the driver adjusts the decay time to keep the current waveform in regulation instead of using a fixed fast or slow decay. In practice that means a stepper runs quieter and cooler than it would with a fixed decay, and a brushed motor sees less current ripple. Synchronous rectification is included, so the recirculation current flows through the FETs rather than through the body diodes, and the loss during decay is lower.
Sleep current is 2 microamps, the logic inputs accept 3.3 V and 5 V levels, and protection covers undervoltage lockout, charge pump undervoltage, overcurrent and thermal shutdown. The operating temperature range is minus 40 C to plus 125 C, which is the industrial window rather than the consumer one.
Key data for the DRV8845RHHR
| Operating supply | 4.5 V to 38 V, absolute maximum 40 V |
| Outputs | Four H-bridges, two steppers or four brushed motors or a mix |
| Current | 1.5 A full scale and 2.5 A peak per bridge, 900 mOhm high side plus low side |
| Interface | PHASE and Ixx, two bit current reference per bridge |
| Step modes | Full, half and quarter step for steppers; forward, reverse and coast for DC motors |
| Decay | Smart tune adaptive decay with synchronous rectification |
| Sleep current | 2 microamps typical |
| Protection | Undervoltage lockout, charge pump undervoltage, overcurrent, thermal shutdown |
| Temperature | Minus 40 C to plus 125 C operating |
Body, packing and marking data
| Body | 36-pin VQFN, the RHH outline, 6.00 mm by 6.00 mm, 36 mm squared with an exposed pad |
| Carrier | Tape and reel; the count per reel is read from the vendor addendum row for this order code |
Reading the code before you buy it
DRV8845 is the circuit, RHH is the 36-pin 6 mm QFN and the trailing R is the reel. The vendor states that the footprint and the software are compatible with similar drivers from other vendors, which is a rare claim in this class and the reason the part turns up in printer and vending machines that were originally built around another supplier's quad driver. It also means a change to this part is sometimes a same footprint change, with the current reference levels and the decay behaviour the parts that differ.
The DRV8849 is listed by the vendor as a related part with a different pinout: a dual stepper driver with a STEP and DIR interface and integrated current sensing, so it uses the same silicon ideas with a different control scheme. The two are not interchangeable, and the choice between them comes down to whether the controller wants to send phase signals or step pulses.
There is no SPI on this part, so there is no register map and no diagnostics beyond the fault pin. For a machine with four axes that is a saving in start up time; for a machine that has to report which axis stalled it is a limitation. Our pin to pin cross reference page tracks the quad driver families we can offer when a given order code is short.
Where the DRV8845RHHR fits
Printers and multi function devices use a quad driver for the paper feed, the carriage, the duplex mechanism and the scanner, which is four motors on one package and one heat path. Vending machines and kiosks use it for the elevator, the dispenser, the shutter and the bill path, and there the 1.5 A per bridge fits the small gear motors that these mechanisms use.
Laboratory instruments and medical analysers use two steppers on one package for the sample probe and the plate handler, plus the two spare bridges for a pump and a valve. The quarter step mode is enough for those mechanisms, and the smart tune decay keeps the audible noise down in a benchtop instrument.
Where it does not fit is a mechanism that needs 1/256 microstepping or stall detection. Those functions are in the dual stepper drivers with integrated sensing, not in this quad. Our one stop BOM sourcing page covers how we line up the drivers, the FETs and the passives for a multi axis build in one order.
Questions we get on this code
Can two bridges drive one larger motor? The vendor does not publish a parallel bridge mode for this part, so the 1.5 A per bridge is the limit per winding. A load that needs 3 A on one shaft needs a driver with a parallel mode or a higher current bridge.
What does the two bit current reference give in practice? Four levels, usually 100, 71, 38 and 0 percent of the full scale, so the current can be reduced for a light load without changing the sense resistor. It is a coarse control and it is set by pins, so it cannot be changed in software during a move.
Why is the on resistance 900 mOhm when a dual driver in the same family is 330? Because four bridges in a 6 mm package have less silicon per bridge. At 1.5 A full scale the loss per bridge is about 2 W if both phases conduct, and the package pad is the limit on how much of that can be removed.
Does smart tune need any setup? It runs from the pin configuration and needs no register, but the motor inductance affects how well it works. A very low inductance motor with a high current ripple is the case where a fixed decay may be preferable, and this part does not offer that option.