DRV8832DGQR
Product Specifications
DRV8832DGQR
Texas Instruments — Power Management & Signal Chain
Product Overview
The DRV8832DGQR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
DRV8832DGQR: voltage regulated drive for a single lithium cell
The DRV8832DGQR is the 10-pin HVSSOP body of the DRV8832, a single H-bridge motor driver built for low voltage battery products. It operates from 2.75 V to 6.8 V, delivers up to 1 A of DC or peak current with 450 mOhm of on resistance, and it does something most small drivers do not: it regulates the voltage it applies to the motor rather than leaving the motor to follow the battery.
That voltage regulation is the whole point of the part. In a battery product the pack voltage falls from 4.2 V to 3.0 V over a discharge, and a motor driven directly from it slows down as the pack empties. The DRV8832 takes a reference level set by a resistor divider and holds the average voltage across the motor at that level, so the mechanism runs at the same speed on a fresh pack and on a nearly empty one. A built in reference output is provided for that divider, which keeps the setting stable as the battery moves.
The bridge is a single H, so it drives one brushed motor, one winding of a stepper, or a solenoid or another inductive load. A current limit circuit holds the motor current at a set point during start up and stall, and a fault output tells the host controller that a limit or a thermal event has happened. Sleep current is 300 nanoamps typical, which is low enough that a battery toy can sit on a shelf for months with the driver connected.
The supply window is what decides the application. 2.75 V minimum covers a single lithium cell down to its cutoff and covers three alkaline cells at end of life. 6.8 V maximum means a 5 V rail is the practical ceiling, so this is not a 12 V part. The operating temperature range is minus 40 C to plus 85 C.
Key data for the DRV8832DGQR
| Operating supply | 2.75 V to 6.8 V, absolute maximum 7 V |
| Output | One H-bridge, drives a brushed motor, one stepper winding, a solenoid or another load |
| Current | 1 A DC or RMS, 1.3 A peak, with 450 mOhm high side plus low side |
| Regulation | PWM voltage regulation against a programmable reference, built in reference output |
| Current limit | Adjustable, acts during start up and stall |
| Fault reporting | Fault output pin to the host controller |
| Sleep current | 300 nanoamps typical |
| Protection | Overcurrent, short circuit, undervoltage lockout, thermal shutdown |
| Temperature | Minus 40 C to plus 85 C operating |
Body, packing and marking data
| Body in this code | 10-pin HVSSOP, the DGQ outline, 3.00 mm by 4.90 mm, 14.7 mm squared with a PowerPAD |
| Other body | 10-pin VSON, the DRC outline, 3.00 mm by 3.00 mm, 9 mm squared |
| Carrier | Tape and reel; the count per reel is read from the vendor addendum row for this order code |
Reading the code before you buy it
DRV8832 is the circuit, DGQ is the 10-pin HVSSOP and the trailing R is the reel. The same circuit in the 3 mm VSON carries DRC, which is the body used when the board is dense and the thermal path goes through the pad into an inner plane. The two bodies are electrically identical and mechanically different, so a board change between them is a footprint change.
The regulation scheme is what separates this part from the DRV8833 and DRV8847 dual bridges in the same low voltage band. Those parts regulate current; this one regulates voltage. A product that needs constant speed from a falling battery wants the voltage loop, and a product that needs constant torque wants the current loop. Choosing the wrong one produces a mechanism that either slows as the battery drains or stalls when the load rises, and neither fault looks like a driver fault at first.
The letters after the body code do not carry a temperature grade here, because the whole circuit is published at minus 40 C to plus 85 C. That ceiling is the practical limit for a handset or a toy and the reason this order code does not appear in automotive builds. Our pin to pin cross reference page keeps the low voltage family side by side for that reason.
Where the DRV8832DGQR fits
Battery powered toys, electric toothbrushes, handheld tools and small appliances are the classic use: one motor, a single lithium cell or three alkalines, and a requirement that the motor sound and speed stay constant as the battery drains. The voltage loop holds that, and the 300 nA sleep current means the driver does not drain the pack between uses.
Portable printers and label makers use the part for the paper feed, where the motor has to pull at a constant speed regardless of the roll diameter and the pack voltage. Portable medical devices use it for a pump or a valve where the dose depends on the motor speed, and there the built in reference is a documented way to hold the setting over the discharge curve.
Where it does not fit is any load above 1 A or any rail above 6.8 V. A 12 V mechanism needs the 18 V dual bridge family, and a 2 A motor needs a driver with a larger bridge. Our medical device components page covers the parts we hold for the portable builds where this driver is specified.
Questions we get on this code
How is the regulated voltage set? By a resistor divider from the built in reference to the VSET pin. The divider ratio sets the average voltage across the motor, and because the reference is internal and stable the setting does not change with the battery. The divider values are a calculation rather than a guess, and the datasheet tables give the ratio for the common settings.
What happens when the battery is below the setting? The driver cannot regulate above the supply, so it passes the pack voltage through and the motor slows. That is the graceful end of the discharge curve, and a product that needs full speed to the last drop has to set the regulator below the minimum pack voltage.
Does the current limit conflict with the voltage loop? They work on the same bridge, and the current limit wins when the motor is starting or stalled. The voltage loop then takes over once the motor is turning and the current has fallen below the limit, which is why both are needed on a mechanism that has a high start up current.
Why the HVSSOP body rather than the smaller one? Because the HVSSOP with its exposed pad is easier to inspect and rework and it takes a wider thermal path into the board. A high volume board with an inner copper plane uses the 3 mm VSON, and a prototype or a low volume build uses the HVSSOP.