DRV8701ERGER
Product Specifications
DRV8701ERGER
Texas Instruments — Power Management & Signal Chain
Product Overview
The DRV8701ERGER from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
DRV8701ERGER: a gate driver for the FETs you choose
The DRV8701ERGER is the 4 mm QFN body of the DRV8701E, a single H-bridge gate driver that drives four external N-channel MOSFETs instead of carrying its own output stage. That distinction is the whole reason the part exists: the current rating of the bridge is set by the FETs on the board rather than by the driver, so one 4 mm part covers a 10 A actuator and a 50 A one, and the heat is spread across the FETs rather than concentrated in a package the size of a fingernail.
The supply range is 5.9 V to 45 V operating with 47 V absolute maximum, which is aimed at the 12 V and 24 V brushed motor systems that dominate pumps, valves, seat motors, window lifts and robotics. The gate drive is 9.5 V at the gate, strong enough to turn a standard level FET fully on, and the drive current is set by one resistor on the IDRIVE pin across five levels from 6 mA to 150 mA source and 12.5 mA to 300 mA sink. That resistor is the knob that trades switching speed against ringing, and it is the first thing to change when a board fails an EMC test.
Inside the part there is a current shunt amplifier with a fixed gain of 20, a PWM current regulation loop with fixed off time, two low dropout regulators that can supply external loads, and a charge pump that supports 100 percent duty cycle. The regulators are the detail that saves board space: AVDD gives 4.8 V at up to 30 mA and DVDD gives 3.3 V at up to 30 mA, enough for a small controller and its sensors in a module that has only one supply pin.
The E in the part number is the interface: PH and EN pins, one for direction and one for enable or PWM. The P version of the same circuit uses a PWM interface instead, and the two are not interchangeable in software even though the pin count is the same. Sleep current is 9 microamps, the logic inputs accept 1.8 V, 3.3 V and 5 V levels, and the protection set covers undervoltage, charge pump fault, overcurrent, short circuit, predriver fault and thermal shutdown.
Key data for the DRV8701ERGER
| Operating supply | 5.9 V to 45 V, absolute maximum 47 V |
| Topology | Single H-bridge gate driver for four external N-channel MOSFETs |
| Gate drive | 9.5 V at the gate, 6 mA to 150 mA source and 12.5 mA to 300 mA sink, five levels |
| Interface | PH and EN pins on the E version, PWM interface on the P version |
| Current sense | Internal shunt amplifier, gain 20, feeding a fixed off time PWM current loop |
| Regulators | AVDD 4.8 V at 30 mA and DVDD 3.3 V at 30 mA for external loads |
| Duty cycle | 100 percent supported through the charge pump |
| Sleep current | 9 microamps typical |
| Protection | Undervoltage, charge pump fault, overcurrent, short circuit, predriver fault, thermal shutdown |
Body, packing and marking data
| Body | 24-pin VQFN, the RGE outline, 4.00 mm by 4.00 mm by 0.90 mm, 16 mm squared with a PowerPAD |
| Temperature | Minus 40 C to plus 125 C operating |
| Carrier | Tape and reel; the count per reel is read from the vendor addendum row for this order code |
Reading the code before you buy it
DRV8701 is the circuit, E is the PH and EN interface, RGE is the 4 mm QFN and the trailing R is the reel. The DRV8701P in the same body has the PWM interface, and putting one where the other belongs produces a board that either does not move or moves in the wrong direction at the wrong time, because the pin functions are the same pins carrying different meanings.
The evaluation module uses this part with a small controller on the same board, which is a useful reference for the two regulators: on the vendor module the 3.3 V rail from DVDD runs the controller, so an engineer can see how much current the part can give away before the internal logic starts to suffer. That budget is 30 mA per regulator and it is shared with the gate drive if the FETs are large.
For a second source, the honest answer is that this is a function with several suppliers and no exact pin match. A part from another vendor that also drives four N-channel FETs will have a different pinout, a different IDRIVE scheme and a different sense amplifier gain, so the swap is a board change. Our BOM shortage recovery page describes how we handle that class of swap when the driver is the line down part.
Where the DRV8701ERGER fits
Brushed DC actuators in vehicles are the first case: seat motors, window lifts, tailgate struts, pump motors and valve actuators run from 12 V or 24 V at currents from 5 A to 30 A, and the current has to be limited during a stall. The sense amplifier and the fixed off time loop do that with a shunt in the low side leg, and the FETs are chosen for the current rather than the driver.
Robotics and AGV drives use the same part for the traction motor on a small platform, where the gate drive current has to be high enough to switch a large FET quickly and low enough not to ring. Medical pumps and dental chairs use it because the actuator is a brushed motor with a gearbox and the driver has to be quiet and reliable rather than fast.
Industrial valves, dampers and door operators use the 45 V rating with a 24 V supply, which leaves headroom for the inductive kick when the motor is switched off under load. Our OEM procurement page covers how we hold stock on parts like this one for a build that runs for years.
Questions we get on this code
How are the external FETs chosen? By the stall current and the thermal path, not by the driver. The driver sets 9.5 V of gate drive and a configurable gate current, so a FET with a low gate charge switches in tens of nanoseconds and a large one needs more drive current from the IDRIVE resistor. The vendor recommends starting at the middle level and moving down if the switch node rings.
Does 100 percent duty cycle work at low supply? The charge pump maintains the high side gate voltage above the rail, so a 100 percent duty request holds the high side FET on continuously. That is what a locked actuator at full torque needs, and it is the case where the charge pump current has to be checked against the FET gate charge at the switching frequency.
Can the internal regulators power the controller? AVDD gives 4.8 V at 30 mA and DVDD gives 3.3 V at 30 mA. A small controller with a radio will exceed that, so the regulator is for a sensor or a logic block, and the main controller keeps its own supply.
What is the difference against an integrated driver? An integrated driver is smaller, simpler and fixed in its current rating. This part moves the heat to the FETs, allows any current the FETs can carry, and lets the board use FETs that are already qualified in the product. The trade is more parts, more board area and a gate drive that has to be tuned.