DRV8601NMBR
Product Specifications
DRV8601NMBR
Texas Instruments — Power Management & Signal Chain
Product Overview
The DRV8601NMBR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
DRV8601NMBR: a haptic driver that starts in a hundred microseconds
The DRV8601NMBR is the 2 mm by 2 mm ball grid array body of the DRV8601, a single supply haptic driver for eccentric rotating mass motors and linear resonant actuators. It takes a single ended PWM input and drives the actuator from a 2.5 V to 5.5 V rail with up to 400 mA of output current, and its place in a product is defined by two numbers: a 100 microsecond start up and a 10 nanoamp shutdown current.
The 100 microsecond start up is what makes a touch response feel immediate. A driver that needs a millisecond to settle adds a delay the user reads as a soft or late click, and on a capacitive keypad that delay is the difference between a product that feels mechanical and one that feels like software. The 10 nA shutdown current is the other end of the same requirement: a handset, a tracker or a wearable fires the actuator a few times a minute, so the driver has to cost nothing between events.
Quiescent current is 1.7 mA typical while enabled, which is low enough to leave the driver on during an interaction session. The output stage gives near rail to rail swing under load, and because the output is differential the driver can reverse the voltage across the actuator quickly, which is what stops an ERM in a short time rather than letting it coast. That reversal is also how a linear resonant actuator is braked between pulses.
Supply range is 2.5 V to 5.5 V, so it runs from a single lithium cell directly without a boost, and the enable pin is 1.8 V compatible, so a 1.8 V baseband or a 1.8 V sensor hub can drive it. Protection is output short circuit and thermal, and the operating temperature range is minus 40 C to plus 85 C.
Key data for the DRV8601NMBR
| Operating supply | 2.5 V to 5.5 V, maximum output voltage 5.5 V |
| Output current | 400 mA from a 3.3 V supply |
| Actuator types | Eccentric rotating mass motors and linear resonant actuators |
| Input | Analog or PWM, single ended |
| Start up | 100 microseconds |
| Quiescent current | 1.7 mA typical enabled |
| Shutdown current | 10 nanoamps, enable pin compatible with 1.8 V logic |
| Protection | Output short circuit and thermal protection |
| Temperature | Minus 40 C to plus 85 C operating |
Body, packing and marking data
| Body in this code | 8-ball NFBGA, the NMB outline, 2.00 mm by 2.00 mm, 4 mm squared |
| Other body | 8-pin VSON, the DRB outline, 3.00 mm by 3.00 mm, 9 mm squared |
| Carrier | Tape and reel; the count per reel is read from the vendor addendum row for this order code |
| Note on the vendor page | The feature list names the ZQV package for the 2 mm body while the order code uses NMB, so the addendum row is the authority for the exact ballout |
Reading the code before you buy it
DRV8601 is the circuit, NMB is the 2 mm by 2 mm eight ball package, and the trailing R is the reel. The same circuit in the 3 mm by 3 mm VSON carries DRB, and the two are not footprint compatible: one is a ball grid with 0.5 mm pitch and the other is a leadless package with visible pads. A prototype that is assembled by hand wants the DRB, because a 2 mm BGA cannot be inspected or reworked without X-ray.
The vendor page also carries a warning that the MicroStar BGA outline was discontinued and reworked at one point. That note does not change the order code, but it does mean that a reel with an old date code and a reel from the current build can differ in ball composition. A product that has to meet a lead free declaration should be bought on a recent date code and checked against the material declaration rather than assumed.
There is no second source for this exact function in the same package, so a shortage is a board change rather than a part change. Our component obsolescence management page is where we track parts like this one, because a haptic driver in a 2 mm BGA is the kind of line that a vendor can drop without a replacement in the same body.
Where the DRV8601NMBR fits
Handsets, tablets and handheld terminals use it for the home button and for the keypad, where the 2 mm body fits under the shield can next to the audio codec. Wearables and trackers use it because 1.7 mA of quiescent current and 10 nA of shutdown current extend the interval between charges, and because the 2.5 V floor lets it run from a coin cell or a single lithium cell at the end of discharge.
Handheld instruments and medical devices use it for confirmation feedback on a membrane keypad, where the actuator is a small ERM and the requirement is a crisp click rather than a long vibration. Automotive aftermarket accessories and motorcycle telematics use it for alert feedback in a cab where the ambient noise hides a beep.
The part is not for continuous vibration or for a large actuator. 400 mA from 3.3 V is a small motor, and a linear resonant actuator with a high current coil needs a driver with a boost stage or a higher current rating. Our medical device components page covers the parts we source for the handheld builds where this driver appears.
Questions we get on this code
Can it drive a linear resonant actuator without a resonance tracking loop? It drives one at a fixed frequency, and the frequency has to match the actuator's resonance. A product that uses several actuator batches needs the drive frequency trimmed, or the amplitude falls off as the resonance drifts. This driver has no auto resonance tracking, so the trim is done in the controller.
Is the PWM input filtered internally? The input is a single ended PWM signal and the output follows its duty cycle, so the effective drive is the average of the pulse train. A PWM frequency well above the actuator's mechanical response gives a smooth amplitude, and a frequency near the resonance gives a beat that the user hears as a buzz.
What happens on a 5 V rail? The maximum output voltage is 5.5 V and the supply range ends there, so a 5 V rail is the top of the window and a 5.5 V rail leaves almost no margin for the inductive kick of the motor. A 5 V board should keep the supply at 5 V and put a capacitor at the driver pin.
How is it tested at incoming inspection? A 2 mm BGA cannot be probed, so the check is a functional test on a small fixture with an ERM or an LRA connected, plus a visual and X-ray check of the ball array on a sample from each reel. That is the same routine we run on other BGA parts, described on our incoming inspection plan page.