DRV8434SRGER
Product Specifications
DRV8434SRGER
Texas Instruments — Power Management & Signal Chain
Product Overview
The DRV8434SRGER from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
DRV8434SRGER: 48 V, 2.5 A and stall detection in a 4 mm square
The DRV8434SRGER is the QFN body of the DRV8434S, a bipolar stepper driver rated 48 V and 2.5 A full scale with an SPI interface alongside STEP and DIR. The die carries two H-bridges, the 1/256 microstepping indexer and the current sense, so the two external sense resistors are not needed, and the vendor publishes plus or minus 4 percent full scale current accuracy for that arrangement, which is the tightest figure in this part of the family.
The number that separates it from a plain driver is stall detection. The device watches the back EMF signature of the winding and reports a stall over SPI without a sensor, which is what a mechanism uses to find its end stop or to notice that a valve has closed. There is also open load detection, an overtemperature warning ahead of the shutdown, and a fault output, so the controller can tell the difference between a jammed mechanism and a part that is too hot.
Power is 4.5 V to 48 V operating with 50 V absolute maximum, which covers a 24 V rail with room for the inductive transient and covers a 48 V rail only if the supply is well held. On resistance is 330 mOhm high side plus low side at 24 V and 25 C, so at the 1.8 A rms rating the conduction loss is about 1.07 W across both bridges and the thermal pad has to be soldered to a copper area with vias, not to a thin trace.
Decay options are smart tune, slow and mixed, and off time is selectable at 7, 16, 24 or 32 microseconds. Sleep current is 2 microamps, spread spectrum clocking is included, and the logic inputs accept 1.8 V, 3.3 V and 5 V levels, so a 1.8 V processor can drive it without a level shifter. Daisy chain support over SPI is available for a machine with several axes on one bus.
Key data for the DRV8434SRGER
| Operating supply | 4.5 V to 48 V, absolute maximum 50 V |
| Current | 2.5 A full scale, 1.8 A rms, 4 A peak per bridge |
| On resistance | 330 mOhm high side plus low side at 24 V and 25 C |
| Interface | SPI plus STEP and DIR, daisy chain supported |
| Microstepping | Up to 1/256 with configurable indexer table |
| Current sense | Internal, plus or minus 4 percent full scale, no sense resistors |
| Diagnostics | Sensorless stall detection, open load, overtemperature warning, nFAULT |
| Decay | Smart tune, slow and mixed, off time 7, 16, 24 or 32 microseconds |
| Sleep current | 2 microamps typical |
| Temperature | Minus 40 C to plus 125 C operating |
Body, packing and marking data
| Body in this code | 16-pin VQFN, the RGE outline, 4.00 mm by 4.00 mm, 16 mm squared |
| Other body | 16-pin HTSSOP, the PWP outline, 9.70 mm by 6.40 mm, 62 mm squared |
| Carrier | Tape and reel; the count is per order code and read from the vendor addendum row |
Reading the code before you buy it
DRV8434S is the circuit with the SPI port, RGE is the 4 mm QFN and the trailing R is the reel. The DRV8434 without the S is a different order code with a hardware interface and no SPI, so it has no stall detection registers to read. A buyer who substitutes the plain version for the S version gets a board that runs but cannot report a stall, which is exactly the function the S version was chosen for.
The 16-pin footprint is shared across the family and the vendor publishes the ladder: DRV8428 and DRV8436 below this part at 1500 and 900 mOhm, DRV8434S here at 330 mOhm, then the 55 V and 65 V parts in the 28 pin body. That means a product family can raise the rail without changing the code logic, and it means a counterfeit or a wrongly marked reel is hard to detect by footprint alone. Our how to verify a drop in replacement page covers the electrical checks we run before approving that kind of swap.
One practical note on the letters: the S sits in the circuit name and not at the end, so a search string that looks for a trailing S will miss it. The same is true of the PWP and RGE bodies, where the last letter before the reel suffix is the body and not a revision.
Where the DRV8434SRGER fits
Multi-axis laboratory and medical equipment is the first place to look, because stall detection replaces an end stop switch on every axis and the SPI bus lets one controller read several drivers. Automated pipetting heads, syringe pumps, microplate handlers and optical filter wheels all use the 1.8 A rms band, and all of them benefit from the overtemperature warning arriving before the shutdown rather than after it.
Industrial valve and damper actuators use the 48 V rating and the stall detection together: the motor drives until it stalls against the seat, the driver reports the stall, and the controller records the closed position without a limit switch in a wet or hot environment. Printing and packaging machinery uses the same pair of features for web tension and for the registration adjustment.
The part is also a candidate where a 3D printer or a laser cutter needs more current than a 1.5 A driver gives but the board is already laid out for a 4 mm QFN. In that case the swap is a same footprint change and the only new work is the SPI bus. Our component lead time solutions page covers what we do when the 2.5 A part is on allocation and the 1.5 A part is not.
Questions we get on this code
Does stall detection work at low speed? It works from the back EMF of the winding, so it needs the motor to be turning when the check runs. A mechanism that creeps at a few hundred steps per second has a small signal and the thresholds have to be tuned on the actual motor, which is why the vendor provides registers rather than a fixed trip point. A board that expects a factory setting to work on a new motor will be disappointed.
Is 48 V a real rating or a marketing one? The operating range is 4.5 V to 48 V and the absolute maximum is 50 V, so 48 V is the top of the operating window and not a margin. A 48 V supply that is set at 48 V plus 5 percent is outside the window and has to be trimmed or the part has to be replaced with the 65 V version.
How much copper does the pad need? At 1.8 A rms with 330 mOhm the two bridges dissipate about 1.07 W, and the 4 mm QFN removes that through the exposed pad only. The pad has to be soldered with vias into an inner copper plane, and the plane area is set by the temperature rise that the enclosure allows rather than by the package.
Why choose this over the 65 V part? Cost and size. The 65 V DRV8461 is a 24 or 28 pin body at 300 mOhm and 3 A, so it is bigger, and a 24 V system does not need the headroom. The 48 V part in the 4 mm body is the right choice when the rail is 24 V or 36 V and the current is under 1.8 A rms.