DRV8350HRTVT
Product Specifications
DRV8350HRTVT
Texas Instruments — Power Management & Signal Chain
Product Overview
The DRV8350HRTVT from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
DRV8350HRTVT: the same 100 V driver on a 250 piece reel
The DRV8350HRTVT is DRV8350H in the 32-pin 5 mm by 5 mm WQFN, packed 250 pieces on a 180 mm reel instead of the 3000 piece 330 mm reel of the R suffix. The silicon is identical to DRV8350HRTVR: a 9 V to 100 V three-phase gate driver for external N-channel FETs, hardware interface, no shunt amplifiers, no buck converter. The only difference a buyer sees is the reel size and the price per piece that comes with it.
That difference matters more than it sounds. A 330 mm reel is the production unit, and a line that consumes a few hundred pieces a week does not want a full reel sitting in dry storage where its floor life runs out before the parts are used. A 250 piece reel matches a pilot build, a first article run or a service spares kit, and it costs less to scrap if the build is cancelled. For a machine builder that assembles twenty units a month, the small reel is the difference between a stocked part and a part that ages on the shelf.
The electrical behaviour is the one described for the whole family. Peak gate current of 50 mA to 1 A source and 100 mA to 2 A sink in seven IDRIVE steps, charge pump at VDRAIN plus 10.5 V with 25 mA average, low side regulator at 14.5 V with 11 V at the gate outputs, VDS overcurrent in seven steps on a resistor, 1x PWM with an internal commutation table for 120 degree sensored drive, and 20 uA of sleep current at 48 V.
Moisture sensitivity is level 2 on both reel sizes, with a one year floor life at 260 C peak reflow. That is the same for the G4 row, which is the lead free version of the same string and also ships 250 pieces on a small reel. A purchasing team that has to choose between the plain and the G4 order codes should know that both are active and both are on the small reel, and that the difference is in the finish documentation rather than in the function.
Key data for the DRV8350HRTVT
| Operating range | 9 V to 100 V on VM, same silicon as the R suffix |
| Outputs | Three half bridges for external N-channel FETs |
| Gate current | 50 mA to 1 A peak source, 100 mA to 2 A peak sink |
| Gate supplies | VCP at VDRAIN plus 10.5 V, VGLS 14.5 V, gate outputs 11 V |
| Protection | VDS overcurrent in seven steps, gate to source monitor, shoot through prevention, thermal shutdown |
| PWM modes | 6x, 3x, 1x and independent, 1x with an internal commutation table |
| Sleep current | 20 uA typical at 48 V VM |
| Logic | 1.8 V, 3.3 V and 5.0 V CMOS inputs |
| Not fitted | No shunt amplifiers, no buck regulator, no SPI on this suffix |
Body, packing and marking data
| Body | 32-pin WQFN, the RTV outline, 5.00 mm by 5.00 mm, 0.75 mm maximum height |
| Carrier | 250 pieces on a 180 mm small tape and reel, the T suffix |
| Reel envelope | 180 mm reel, 12.4 mm tape width, pocket 5.3 mm by 5.3 mm, 1.1 mm deep |
| Finish | NIPDAU lead finish, moisture level 2, 260 C peak reflow, one year floor life |
| Temperature | Minus 40 C to plus 125 C operating |
| Marking | DRV8350H on the body, lot and date code on the reel label |
Reading the code before you buy it
The last letter is the only one that separates this part from the production reel: DRV8350HRTVR is 3000 pieces on a 330 mm reel and DRV8350HRTVT is 250 pieces on a 180 mm reel. Everything before that letter is the same, which is why a purchase order that quotes the string from memory rather than from the drawing can deliver ten times the quantity that was intended. On a 250 piece order the difference in cost is not trivial.
There is a second row in the same addendum that deserves attention: DRV8350HRTVTG4. It is the same 250 piece small reel with a G4 lead free marking, active and in production, but its moisture row reads level 2 with a one year floor life exactly like the plain row. A buyer who sees a G4 suffix and assumes a different reflow profile is solving a problem that is not there, and a buyer who ignores the G4 suffix may be holding a finish that the end customer's material declaration does not accept.
The large reel rows also carry the packing material dimensions, and those are what an automated line needs: 12.4 mm tape width, 5.3 mm by 5.3 mm pocket, 1.1 mm depth, 8 mm and 12 mm tape and reel leader and trailer. A feeder set up for a 330 mm reel does not take a 180 mm reel without a change of the reel holder, which is a line change rather than a purchasing choice.
Where the small reel earns its place
Pilot builds are the obvious case. A first article run of 50 drives consumes 50 parts, and the remaining 200 on the reel cover the second build and the spares kit. The alternative is to buy 3000, hold 2900 against a floor life that expires in a year, and carry the risk that the board changes before the reel is empty.
Service and repair organisations use the same reel for the same reason. A repair centre that replaces a driver board a few times a month does not want a production reel, and a 250 piece reel in a sealed bag with a level 2 rating is a stock item that can sit on a shelf and stay inside its floor life with dry storage.
Low volume machine builders, laboratory equipment and test fixtures all sit in the same band. A fixture that runs one motor stage and ships a handful a year still needs the 100 V rating and the protection features, and the small reel keeps the part affordable per unit. When several such builds share a driver circuit, the parts list becomes a kitting exercise rather than a purchasing exercise, and our kitting service page covers how the quantities are pooled.
Questions we get on this code
Is the T suffix a different silicon? No. Same die, same body, same marking, same electrical tables. The T is a packing code, and the packing code is the one thing on the order that changes what arrives in the box.
Can a 180 mm reel run on the same feeder as a 330 mm reel? Only with a reel adapter or a change of the holder. The tape width is the same 12.4 mm, so the feeder pitch and the pocket are identical, and the change is mechanical at the reel mount rather than at the nozzle.
Does a small reel cost more per piece? Almost always, and it should. The reel, the leader and trailer tape, the packing labour and the test lot are spread over 250 pieces instead of 3000. A buyer comparing the two strings on unit price alone is comparing two different services.
How long can the parts sit on the shelf? Level 2 means the floor life after the bag is opened is one year at 30 C and 60 percent relative humidity, and the sealed bag keeps that clock from starting. A small reel that is opened, used for 50 pieces and resealed should be stored dry, because the clock does not stop when the bag is closed again.
What if the small reel is out of stock and the build cannot wait? The same die is on the large reel, so the alternative is to buy the R suffix and either use the reel or have the parts re-reeled into a smaller carrier. Both routes need planning ahead of the build date, and our component lead time page sets out how that decision is made against a line stop.