Contact Us

DRV8350HRTVR

Brand: Texas Instruments
Texas Instruments DRV8350HRTVR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

DRV8350HRTVR — Power Management & Signal Chain | Superb Automation

DRV8350HRTVR

Texas Instruments — Power Management & Signal Chain

Product Overview

The DRV8350HRTVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

DRV8350HRTVR: a 100 V three-phase gate driver for external FETs

The DRV8350HRTVR is the plain hardware member of the DRV835x family: three half-bridge gate drivers in a 32-pin 5 mm by 5 mm WQFN, driving six external N-channel FETs from a 9 V to 100 V rail. It carries no current sense amplifiers and no buck regulator, so the whole part is gate drive, charge pump, protection and a resistor configurable interface. That is exactly what a drive stage that already has its own shunt amplifiers and its own housekeeping rail needs.

Peak gate current is 50 mA to 1 A source and 100 mA to 2 A sink, adjustable in seven IDRIVE steps. The high side is fed by a doubler charge pump regulated to VDRAIN plus 10.5 V with 25 mA of average output; the low side has a linear regulator that holds VGLS at 14.5 V and clamps the gate outputs at 11 V. The pump drops into full doubler mode below 12 V of VM and produces twice VM minus 1.5 V unloaded, so a 12 V system still gets a usable gate voltage at the bottom of the pack.

Protection is the part of the story that saves boards. A VDS comparator on each phase watches the drain to source voltage of the external FETs and trips in one of seven steps set by a resistor; the same block catches a short to ground, a short to the rail and a phase to phase fault, because all three show up as excess VDS on a FET that is supposed to be on. A gate to source monitor catches a FET with a damaged gate, a minimum dead time block prevents shoot through, and a strong pulldown resists the dV/dt that would otherwise turn a FET back on through its own gate charge.

The PWM block accepts 6x, 3x, 1x and independent inputs. The 1x mode uses an internal block commutation table and three hall inputs, which removes the commutation logic from the controller and lets a small microcontroller run a sensored trapezoidal drive with one PWM line. On a 100 V stage that mode is often the difference between a 32-pin controller and a 64-pin one.

Key data for the DRV8350HRTVR

Operating range9 V to 100 V on VM, 100 V absolute maximum reference through VDRAIN
OutputsThree half bridges, external N-channel FETs, high side and low side
Gate current50 mA to 1 A peak source, 100 mA to 2 A peak sink, seven IDRIVE steps
Charge pumpVDRAIN plus 10.5 V regulated, 25 mA average, full doubler below 12 V
Low side regulatorVGLS at 14.5 V, gate outputs at 11 V
OvercurrentVDS comparator per phase, seven thresholds on the VDS pin
PWM modes6x, 3x, 1x and independent, 1x with an internal commutation table
Sleep current20 uA typical at 48 V VM
Logic1.8 V, 3.3 V and 5.0 V CMOS inputs
Not fittedNo shunt amplifiers, no buck regulator, no SPI on this suffix

Body, packing and marking data

Body32-pin WQFN, the RTV outline, 5.00 mm by 5.00 mm, 0.75 mm maximum height
Carrier3000 pieces on a 330 mm large tape and reel
FinishNIPDAU lead finish, moisture level 2, 260 C peak reflow, one year floor life
TemperatureMinus 40 C to plus 125 C operating
MarkingDRV8350H on the body, lot and date code on the reel label

Reading the code before you buy it

DRV8350 is the 100 V circuit, H is the hardware interface, RTV is the 32-pin body, and the final R is the large reel. The letters before the body are the ones that carry meaning: an S in place of the H gives the SPI version, an R after the circuit name adds the 350 mA buck, and a 3 instead of a 0 adds the three current shunt amplifiers. Stacking them gives the fuller parts, and each combination has its own body size and its own order code.

Two suffixes look alike and are not. DRV8350HRTVR and DRV8350RHRGZR differ by a single R placed after the circuit name, and the second one is a 48-pin 7 mm by 7 mm part with a buck regulator inside. On a purchase order the difference is easy to miss and expensive to correct, because the reel looks similar and the marking differs by two characters. The check is the pin count on the label against the drawing, not the resemblance of the string.

There is also a wide body variant of the same family in the automotive and higher power world, and it is not this part. When a distributor offers a DRV835x at a price below the family norm, the first question is which body it is, because the 5 by 5 part and the 7 by 7 part have different thermal paths and different gate drive strengths at the same headline current.

Where the DRV8350HRTVR fits

48 V and 60 V servo drives are the core case. The 100 V rating leaves room for the regeneration spike, the external FETs set the power level, and the 1x mode lets a compact controller run a sensored motor without a commutation table in software. Fans, blowers and pumps in industrial cabinets use the same driver at a lower current with the same order code.

E-bikes, e-scooters and light mobility platforms run the part from a 48 V pack and use the VDS comparator as the stall detector. When a wheel is blocked, the current rises until the FET drain voltage crosses the threshold, and the driver latches off or retries depending on the configuration. That is a protection scheme that costs no extra parts and works on every phase.

Linear motor transport and textile machines use the adjustable slew rate to keep emissions low across a long cable run. A slow gate edge costs switching loss and saves an EMC filter, and on a 100 V stage with a 2 m cable that trade is usually worth taking. Buyers building several power levels from one driver usually keep a cross reference of which FET and which threshold go with each, and the power management cross reference page is where that comparison starts.

Questions we get on this code

How much current can this driver handle? None of it. The driver passes gate charge, not motor current, so the answer depends entirely on the external FETs and their thermal path. The limits that belong to the driver are the 1 A source and 2 A sink peak, the 25 mA average from the charge pump, and the gate charge that those numbers allow at the switching frequency in use.

Why is the low side regulator 14.5 V and the gate output 11 V? The regulator has to sit above the gate clamp so that the clamp, not the regulator, sets the gate voltage. An 11 V gate is the compromise between on resistance and gate oxide stress on a 100 V FET, and it also keeps the gate charge, and therefore the drive current, below the point where the charge pump runs out.

Can the VDS threshold be changed after the board is built? Yes, it is a resistor, so a rework changes the trip point without touching the silicon. The threshold is also the only overcurrent protection on the part, so a value chosen for a 20 A stage will not protect a 5 A stage, and a board that is re-rated for a smaller motor has to be reworked for the new threshold.

Does the driver need a separate 12 V rail? No. Everything the gate drive needs comes from VM through the charge pump and the low side regulator, which is why the part works from a single 48 V bus. The exception is a system that keeps VM alive in sleep and wants the logic rail up, and that is what the 20 uA sleep mode is for.

What if the drive has to log why it tripped? This suffix does not, because the hardware interface exposes a single nFAULT pin. The SPI members of the family read back the fault register, which is the difference between a drive that reports a fault and a drive that reports which FET failed. For a warranty investigation that difference decides the answer, and our strategic sourcing page covers how to keep both variants available for the two builds.