DRV8251ADDAR
Product Specifications
DRV8251ADDAR
Texas Instruments — Power Management & Signal Chain
Product Overview
The DRV8251ADDAR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
DRV8251ADDAR: 4.1 A brushed DC motor driver with an integrated current mirror in an eight pin HSOP
DRV8251ADDAR is a single H-bridge motor driver in the eight pin DDA body that runs from 4.5 V to 48 V, integrates the four switches at 450 milliohm total and reports load current through an internal mirror instead of an external shunt in a HSOP with PowerPAD body of 8 pins. The DRV8251A is the current mirror member of the DRV8251 pair, alongside the shunt based DRV8251. It is an N-channel H-bridge with an operating range of 4.5 V to 48 V, a 4.1 A peak output rating and 450 milliohm of combined switch resistance. The body is an eight pin HSOP with a PowerPAD measuring 4.9 mm by 6.0 mm, and the interface is a PWM input pair with a sleep mode that draws under 1 uA at 24 V.
Order code and package
| Order code | DRV8251ADDAR |
| Function | single H-bridge brushed DC motor driver |
| Operating supply voltage | 4.5 V to 48 V |
| Peak output current | 4.1 A |
| Combined switch resistance | 450 milliohm |
| Current sense | integrated mirror, IPROPI output |
| Logic inputs | 1.8 V, 3.3 V and 5 V compatible |
| Sleep current | under 1 uA at 24 V and 25 C junction |
| Package | eight pin HSOP with PowerPAD, 4.9 mm by 6.0 mm |
| Family | DRV8870, DRV8251, DRV8231 and the mirror versions |
Electrical parameters that decide the application
| Thermal resistance, junction to case bottom | 4.2 C per W |
| Thermal resistance, junction to case top | 54.7 C per W |
| Thermal resistance, junction to board | 14.4 C per W |
| Junction to top characterization parameter | 4.1 C per W |
| Junction to board characterization parameter | 14.4 C per W |
| Junction temperature range | minus 40 C to 150 C |
| DRV8870 comparison | 6.5 V to 45 V, 565 milliohm, shunt based |
| DRV8251 comparison | 4.5 V to 48 V, 450 milliohm, shunt based |
| DRV8231 comparison | 4.5 V to 33 V, 600 milliohm, shunt based |
| DRV8231A comparison | 4.5 V to 33 V, 600 milliohm, mirror based |
Points to check before this part goes on a BOM
The 450 milliohm figure is the sum of the high side and low side switch resistances, so it describes a current path rather than a component. At 1 A the bridge dissipates 0.45 W, at 2 A it is 1.8 W and at the 4.1 A peak it is 7.6 W. With a junction to case bottom resistance of 4.2 C per W and a junction to board figure of 14.4 C per W, the pad and the copper under it carry almost all of that heat, and an eight pin HSOP on a small board cannot hold 7.6 W for long. The peak rating is a transient number and the continuous rating is a thermal one.
The mirror version exists to remove the shunt, and the saving is real at these currents. A 0.1 ohm shunt at 4 A dissipates 1.6 W, which is more than the bridge itself, and it also drops 400 mV of the supply before the motor sees it. The mirror reports a scaled copy of the load current instead, so the board loses that loss and that drop. What it gives up is accuracy: a mirror ratio drifts with temperature and process in a way a metal shunt does not, so the mirror suits stall detection and coarse current limiting and a shunt suits precision torque control.
The family table is the first thing to read before crossing a part number. The DRV8870 stops at 45 V and uses 565 milliohm, the DRV8251 carries 48 V at 450 milliohm, and the DRV8231 pair stop at 33 V with 600 milliohm. All of them come in the same package with the same pin out, so a board can move between them without changing copper, but the 33 V part cannot replace the 48 V part on a 48 V rail and the shunt version cannot replace the mirror version without changing the sense network. The suffix carries the function, not a grade.
A 48 V rating on a motor driver is not the same as a 48 V rating on a regulator. The motor generates a back EMF that adds to the supply during braking, and an H-bridge that is switched off into a spinning motor sees the supply plus that generated voltage at the switch node. A 48 V rail with a motor that generates 30 V at speed puts 78 V across an off switch unless the bridge clamps it, and the internal clamp is what absorbs that energy. The rail should be sized with the braking energy in mind rather than with the nominal supply only.
Sleep current under 1 uA at 24 V is the figure that keeps a module inside a standby budget, and it is one of the few places where the driver is invisible to the rest of the product. What it does not describe is the wake time: the internal regulator and the gate drive have to come up before the bridge can switch, so a controller that asserts the enable and applies PWM in the same millisecond will lose the first pulses. The usual arrangement is to enable, wait for the ready condition or a fixed delay from the data sheet, and then start the PWM.
The PowerPAD is the thermal path and it has to be soldered. With the junction to case bottom resistance at 4.2 C per W and the junction to board figure at 14.4 C per W, an unsoldered pad leaves the part connected to the board through the leads only, which multiplies the rise several times over. Vias under the pad into a copper area on the far side are the difference between a 2 A continuous drive and a 1 A one, and that difference is invisible on the drawing.
The interface is a pair of logic inputs that accept 1.8 V, 3.3 V and 5 V levels, so the driver can sit behind a 1.8 V microcontroller without a level shifter. The two inputs set the four bridge states, and the brake state, where both low side switches conduct, is a useful way to stop a motor quickly without reversing it. Which input combination produces which state is a table in the data sheet, and a firmware change that alters the order of the two signals changes the bridge state during the transition, which is where shoot through is avoided by the internal timing rather than by the software.
Where this order code fits
This order code belongs on brushed DC motors in valve and damper actuators, printers, vending mechanisms, lab automation, door locks and automotive body motors where the rail is 12 V or 24 V and the current is a few amps. It is chosen when stall detection or current regulation is needed and there is no room for a shunt, because the mirror reports the load current from inside the bridge. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Component Lead Time Solutions page.
Questions buyers ask
What is the difference between the DRV8251A and the DRV8251? The letters after the number are the current sense method. The DRV8251 uses an external shunt resistor and the DRV8251A uses an internal current mirror, which reports the load current on the IPROPI pin. The bridge, the voltage range and the switch resistance are the same, so the choice is between the accuracy of a shunt and the loss and space that the shunt costs.
Can 4.1 A be run continuously? Not in an eight pin HSOP on a normal board. At 4.1 A the bridge dissipates about 7.6 W, and the junction to board resistance of 14.4 C per W turns that into a rise of well over 100 C before the ambient is counted. The 4.1 A figure is a peak rating for acceleration and stall events. A continuous current of 2 A is a more realistic ceiling, and even that needs the pad soldered to a copper area with vias.
Does the internal mirror remove the need for any sense resistor? It removes the power shunt in the motor path. A small resistor is still needed from IPROPI to ground to turn the mirrored current into a voltage for the controller, and its tolerance becomes part of the current reading. The mirror ratio itself has a tolerance and a temperature drift that a metal shunt does not, so the reading is good enough for stall detection and coarse limiting and not good enough to replace a calibrated measurement.
What happens to the motor when the bridge is disabled? The bridge goes high impedance, so the motor coasts and its back EMF appears at the outputs. On a 48 V rail a motor spinning at speed can push the switch node above the supply, and the internal clamp absorbs that energy only up to its rating. A drive that has to stop a heavy load quickly needs the brake state, where both low side switches conduct, rather than a disable.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the OEM Procurement page sets out the checks that keep a substitute from failing on the bench.