DRV8245SQPWPRQ1
Product Specifications
DRV8245SQPWPRQ1
Texas Instruments — Power Management & Signal Chain
Product Overview
The DRV8245SQPWPRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
DRV8245SQPWPRQ1: 32 A with an SPI port that makes its own logic rail
The DRV8245SQPWPRQ1 is the third interface option on the 32 A DRV824x-Q1 die. It has the same 40 mOhm HTSSOP bridge, the same 4.5 V to 35 V window and the same 32 A maximum output as the H and P variants, and it adds an SPI port with a logic supply generated inside the part.
The S matters on a module that has no spare low voltage rail. A body module that carries only the battery, a CAN transceiver and this bridge can talk SPI without adding a regulator, which saves a component, a quiescent current and a rework of the board. The interface level is then fixed by the part, so the controller has to accept what comes back rather than set it.
Everything that makes the family useful is present: high-side current sense on IPROPI without a shunt, on and off state load diagnostics, VM monitoring, overcurrent and overtemperature protection with a configurable reaction, spread spectrum clocking to move the switching energy away from a narrow band, and automatic dead time so the two halves of the bridge cannot overlap.
Key data for the DRV8245SQPWPRQ1
| Supply | 4.5 V to 35 V operating, 40 V absolute maximum on VM |
| On resistance | 40 mOhm high side plus low side in HTSSOP, 32 mOhm in VQFN-HR |
| Current | 32 A maximum output, high-side mirror sense on IPROPI |
| Interface | SPI with an internally generated logic supply, plus nFAULT |
| Switching | PWM up to 25 kHz, automatic dead time, spread spectrum clocking |
| Diagnostics | On and off state load diagnostics, VM monitoring, overcurrent, overtemperature |
| Qualification | AEC-Q100 grade 1, minus 40 C to plus 125 C ambient, functional safety capable |
Body, packing and marking data
| Body | 28-pin HTSSOP with exposed pad, the PWP body, 9.7 mm by 4.4 mm |
| Carrier | 2500 pieces on a large tape and reel, 330 mm reel, 16 mm tape |
| Finish | Nickel palladium gold, moisture level 3, 168 hour floor life at 260 C |
| Marking | DRV8245S plus the lot and date code on the reel label |
Reading the code before you buy it
DRV8245SQPWPRQ1 reads as DRV8245, S, PWP and RQ1. It is the third of three strings that share one footprint and three different jobs, and the ordering mistake that hurts most is buying the S variant for a board that already regulates 3.3 V and expects the SPI lines to sit at that level. The part will run, but the interface sits at its own level and the margin is gone.
The other thing to check is the difference between the S strings across the family. DRV8244S is the 21 A member in the 16-pin VQFN-HR body, while DRV8245S is the 32 A member in the 28-pin HTSSOP. Same letter, different current, different body, and the reels are 3000 against 2500.
An automotive line also has to look at the moisture level. Level 3 with a 168 hour floor life applies to the PWP body in all three variants, which means the reels need a dry cabinet and a bake plan rather than open shelving. That is a procurement constraint, not an electrical one, and it is the one that most often catches a new supplier.
The default register values deserve a paragraph of their own. A part that generates its own logic supply also comes up without a host, so the bridge has to be usable before the controller has spoken to it. The vendor sets defaults that drive a load safely at a conservative slew rate and current limit, and the controller then narrows them once the link is up. A module that loses its SPI link during a drive cycle keeps working rather than dropping the load.
That behaviour is also the reason the fault reaction has to be chosen with care. A latched reaction survives a controller reset, and a retry reaction clears itself as soon as the short goes away. For a pump that must not restart by itself after a jam, the latch is the right setting, and for a fan that has to keep running, the retry is. Both are register fields on this part, which is a more honest way to handle the question than a hardware strap that nobody documents.
Where the self powered interface earns its place
Remote actuators are the first case. A pump or a fan that sits at the end of a harness and has only two power wires plus a CAN pair cannot host a regulator without another component and another quiescent drain, so a bridge that makes its own logic rail is the simplest module.
Retrofit modules are the second case. When a supplier replaces a relay and a fuse with a smart bridge inside an existing housing, the available pins are fixed and a spare 3.3 V is usually not among them. The S variant fits that socket without a board rework.
Single load modules with diagnostics are the third. The SPI port reports which protection tripped, and the part still drives the load if the controller never talks to it, because the default register values are usable. Buyers placing this family against a scheduled build can check availability routes on the component lead time page.
Questions we get on this code
The first question is whether the internal logic supply can be loaded. It cannot. It runs the digital core and the interface, and its current budget is not published as a general rail for a reason.
The second question is what the part does before the controller configures it. It comes up with usable defaults, so a module that loses its SPI link still drives the load rather than sitting dead. That behaviour is what makes the part usable in a safety path where the controller can fail.
The third question is how the 25 kHz ceiling was chosen. It sits above the audible band and below the point where the switching loss in a 40 mOhm bridge becomes the dominant term. A load that needs 100 kHz needs the DRV8263 family instead.
The fourth question is whether the SPI port is worth it on a single load. On one bridge with one job the answer is usually no, because the hardware variant is cheaper and has no bus to protect. The port earns its cost when the module has to report why it stopped, or when the same board serves more than one vehicle variant.
The fifth question is what happens on a loss of the logic supply inside the part. The bridge goes to a safe state and the fault pin reports it, which is the reason the S variant is acceptable in a module that has no independent supervisor. The wiring of that pin into the module harness is covered on the OEM procurement page.