Contact Us

DRV8245HQPWPRQ1

Brand: Texas Instruments
Texas Instruments DRV8245HQPWPRQ1 is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

DRV8245HQPWPRQ1 — Power Management & Signal Chain | Superb Automation

DRV8245HQPWPRQ1

Texas Instruments — Power Management & Signal Chain

Product Overview

The DRV8245HQPWPRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

DRV8245HQPWPRQ1: 32 A and 40 mOhm with a hardware interface

The DRV8245HQPWPRQ1 is the highest current member of the DRV824x-Q1 family, 32 A maximum output with 40 mOhm of combined on resistance in the HTSSOP body and 32 mOhm in the VQFN-HR body. It runs from 4.5 V to 35 V, switches at up to 25 kHz with automatic dead time, and reports load current on IPROPI from a high-side mirror.

The H in the string means hardware interface. There is no serial port on this part. The mode, the slew rate, the current limit and the fault reaction are all set by pins and resistors, which makes the bill of materials smaller and the behaviour fixed at build time rather than at boot. On a load that has one job, such as a fan or a pump, that is the right trade.

The PWP body is the 28-pin HTSSOP with an exposed pad, 9.7 mm by 4.4 mm, and it is the body that most automotive modules already have tooling for. The part is AEC-Q100 grade 1 and carries functional safety documentation, so it can sit in a module that has to make a diagnostic claim.

Key data for the DRV8245HQPWPRQ1

Supply4.5 V to 35 V operating, 40 V absolute maximum on VM
On resistance40 mOhm high side plus low side in HTSSOP, 32 mOhm in VQFN-HR
Current32 A maximum output, high-side mirror sense on IPROPI
InterfaceHardware pins only, no serial port, fault reaction set by pin
SwitchingPWM up to 25 kHz, automatic dead time, configurable slew rate and spread spectrum
DiagnosticsOn and off state load diagnostics, VM monitoring, overcurrent, overtemperature on nFAULT
QualificationAEC-Q100 grade 1, minus 40 C to plus 125 C ambient, functional safety capable

Body, packing and marking data

Body28-pin HTSSOP with exposed pad, the PWP body, 9.7 mm by 4.4 mm
Carrier2500 pieces on a large tape and reel, 330 mm reel, 16 mm tape
FinishNickel palladium gold, moisture level 3, 168 hour floor life at 260 C
MarkingDRV8245H plus the lot and date code on the reel label

Reading the code before you buy it

DRV8245HQPWPRQ1 reads as DRV8245, H, PWP and RQ1. The H is the hardware interface, PWP is the 28-pin HTSSOP, and RQ1 is the automotive grade on a large reel. Change the H to a P and the part gains an SPI port with an external logic rail; change it to an S and the logic rail comes from inside the part. The three strings share a footprint in the same body, which is why a module can be reworked between them without a board change.

The current member is the other half of the code. DRV8243 is 12 A, DRV8244 is 21 A and DRV8245 is 32 A, and all three use the same pin function. That is deliberate: a platform can carry one board and three power levels, and the difference is the die inside the same package.

Moisture level 3 is the detail that decides whether a build plan works. A 168 hour floor life at 260 C means a reel that sits on a line for two weeks has to be baked, and the bake cycle costs more than the price difference between two suppliers. A module built in high volume should plan the reels around the floor life rather than around the storage shelf.

The hardware interface is not a stripped version of the SPI one. Every setting that the SPI variant holds in a register has a pin or a resistor on this part, so the slew rate, the current limit, the fault reaction and the mode are all fixed by components. That is a real advantage in a safety path: nothing that happens on a bus can change the behaviour of the bridge, and a controller that boots slowly still finds the driver in a known state.

The automatic dead time is the other feature that matters when the controller is simple. A timer that produces one PWM signal and one direction signal cannot guarantee a gap between the high and low sides, and a bridge without dead time insertion would rely on the FET body diodes for that interval, which is a loss and a stress. Here the gap is generated inside the part and its length is set by the same resistors that set the slew rate.

Where a 32 A hardware bridge earns its place

Cooling fans and blowers are the first case. A 600 W fan on a 13.5 V rail draws around 45 A at start and 30 A running, which sits just above the 32 A figure, so the parallel half-bridge mode or the VQFN-HR body is the version to specify. A 400 W fan sits comfortably inside the rating with 40 mOhm of conduction.

Electric pumps are the second case. A transmission oil pump or a coolant pump runs continuously at 10 A to 20 A with a stall current above 40 A for a fraction of a second, and the current regulation catches the stall before the connector sees it. The hardware interface is enough here because the pump has one job and the module only needs to know that it ran.

Actuators with a fixed travel are the third. A tailgate or a seat module needs end stop detection rather than a serial port, and the off-state diagnostics plus the IPROPI threshold do that with two pins. Buyers comparing the HTSSOP and the VQFN-HR versions can check the body options on the pin to pin cross reference page.

Questions we get on this code

The first question is whether 32 A can be held continuously. It cannot in the HTSSOP body without a heatsink. At 40 mOhm the bridge dissipates 40 W at 32 A, which is far beyond the package, so the continuous rating in a real module is set by the thermal path and lands nearer 8 A to 12 A with a good pad. The 32 A figure describes the die and the short circuit withstand.

The second question is what happens when the load is shorted. The overcurrent comparator trips on the VDS of the FET, the reaction is set by a pin to latch or retry, and the nFAULT line goes low. A module that must not retry into a short sets the pin to latch and lets the controller decide.

The third question is whether the part can be used at 48 V. It cannot. The family ceiling is 35 V operating and 40 V absolute, so a 48 V system needs the DRV8263 at 65 V, and the two families are not pin compatible.

The fourth question is whether the hardware variant can be reconfigured in the field. It cannot. The slew rate and the current limit sit in resistors and pins, so a change is a board change. A product that has to be reconfigured per customer or per vehicle variant should take the SPI variant and keep the configuration in software.

The fifth question is about second sourcing. The three current members are interchangeable within the same body, which is a rare advantage in an automotive bill of materials, and the delivery risk on this class of part is covered on the component lead time page.