DRV8215RTER
Product Specifications
DRV8215RTER
Texas Instruments — Power Management & Signal Chain
Product Overview
The DRV8215RTER from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
DRV8215RTER: 11 V and 4 A with the speed loop closed inside the driver
The DRV8215RTER is the member of the DRV821x family that closes a voltage and a speed loop on the die. It runs from 1.65 V to 11 V, delivers 4 A peak through a 240 mOhm H bridge, and compares the back EMF of the motor against an internal reference to hold speed without an encoder, a hall sensor or a tachometer wire. The loop is set by a resistor and a capacitor on two pins, so the controller only has to say how fast.
Stall detection is included and is reported on the nFAULT pin. The device measures the back EMF while the motor is driven and compares it against the expected value for the commanded speed, so a jammed gearbox or a blocked flap is caught without a current threshold that drifts with temperature. Overvoltage protection is the other addition over the smaller members, which matters when a motor is braked hard and the supply rail is a battery with a long lead.
The loop components are two passive networks: one sets the target speed as a duty cycle or a voltage, the other sets the loop gain and the time constant. That means the same silicon can hold a small fan at 3000 rpm and a gear motor at 60 rpm, with the difference carried by the passive parts rather than by a controller profile. During a change of supply voltage the loop raises and lowers the duty to keep the measured speed, which is exactly the case a battery powered tool presents as it discharges.
The overvoltage protection is the other practical addition. When the bridge brakes a motor, the kinetic energy goes back into the supply, and a battery with a long lead has enough inductance to push the rail above its nominal value for tens of microseconds. The part clamps that event and reports it, so a product does not need a separate brake resistor for a small mechanism.
The body is the 16-pin WQFN at 3.00 mm by 3.00 mm with a thermal pad, which is the RTE body. The same die in the 8-pin WSON body is the DRV8213, and that part has neither the speed loop nor the stall detection, so the two strings are not interchangeable even though the current rating looks the same, and a buyer comparing them on price alone is comparing two different jobs.
Key data for the DRV8215RTER
| Supply | 1.65 V to 11 V on VM, logic from 1.8 V, 3.3 V or 5 V |
| On resistance | 240 mOhm high side plus low side |
| Current | 4 A peak, internal mirror sense on IPROPI, no external shunt |
| Speed loop | Integrated voltage and speed regulation from back EMF, no sensor needed |
| Stall detection | Reported on nFAULT, threshold set by external components |
| Protection | Overcurrent, thermal shutdown, undervoltage lockout and overvoltage |
| Sleep current | Ultra low quiescent sleep mode, below 60 nA maximum on this family |
Body, packing and marking data
| Body | 16-pin WQFN, the RTE body, 3.00 mm by 3.00 mm with thermal pad |
| Carrier | 3000 pieces on a large tape and reel |
| Finish | Nickel palladium gold, moisture level 1, 260 C unlimited floor life |
| Temperature | Minus 40 C to plus 125 C operating range |
Reading the code before you buy it
DRV8215RTER is DRV8215, RTE and R. The 15 in the family number is the speed regulation member, the 13 is the current regulation member, and both sit in the same datasheet family with a shared pin function up to the point where the loop pins appear.
The practical consequence is that an approved vendor list which lists DRV8213 and DRV8215 as interchangeable is wrong in one direction. A DRV8215 can do everything the 8213 can, but a board laid out for the 8213 has no components on the loop pins, so the speed regulation would run open loop. The 8215 in an 8213 socket is a working motor driver with a loop that does nothing useful.
The second item to settle is the sensing resistor at IPROPI. It sets the voltage the controller reads for current, and it also sets the voltage that the internal regulation compares against. A value copied from a DRV8213 board without checking the regulation threshold gives a current limit that is off by the ratio of the two thresholds.
Where a closed speed loop earns its place
Battery tools and small appliances are the first case. A pump or a fan that has to hold a set flow across a battery that falls from 8.4 V to 6.0 V can use the speed loop to keep the flow constant, and the controller only has to send a target. Without the loop, the same job needs a tachometer wire and a software loop with a tuning exercise per motor.
Automotive flaps and valves are the second case. A HVAC actuator that has to reach a position and hold it against a spring can use the stall detection to know when it has arrived, which removes the end stop switch. The overvoltage protection earns its place here as well, because a flap driven to a hard stop and then released can push current back into the rail.
One caution belongs with the speed loop on a gear motor. The loop reads back EMF through the same bridge that drives the motor, so a gearbox with a large backlash lets the motor speed up and slow down inside one revolution, and the loop tries to correct a ripple it cannot see at the sample rate. A time constant longer than one revolution smooths it, at the cost of a slower response to a real load change.
Portable printers and dispensers are the third case. The paper feed motor runs at a speed set by the print head, the stall detection catches a paper jam before the gearbox strips, and the 3 mm body fits beside the connector. Buyers comparing this family against other 4 A drivers can use the power management cross reference page for the pinout and sense differences.
Questions we get on this code
The first question is how the loop behaves at zero speed. Back EMF is zero when the motor is stopped, so the speed loop cannot start a motor from rest on its own. The controller has to command a start and let the loop take over above a minimum speed, which the vendor states in the functional description rather than in the feature list.
The second question is whether stall detection needs a minimum current. It does, because a stall on a very light load looks the same as a slow ramp. The threshold components have to be chosen for the motor that is actually fitted, and a board that ships with two motor options needs two component sets.
The third question is thermal. The 240 mOhm bridge at 2 A continuous dissipates just under 1 W, which the 3 mm body can only move with a thermal pad tied to a copper pour. The 4 A peak rating is a transient figure and does not describe a continuous load.
The fourth question is about supply. A board that runs on a 12 V rail cannot use this part even though the motor only needs 6 V, because 11 V is the ceiling on VM. The 4.5 V to 33 V members of the family are on the component lead time page for buyers who need a higher rail.
The fifth question is whether the speed loop can be disabled. It can, by biasing the loop pins so that the regulation amplifier stays out of the way, and the part then behaves as a plain 4 A bridge with current sense. That is the reason a single board can serve a sensorless pump and a plain mechanism without a second part number.