DRV8210DSGR
Product Specifications
DRV8210DSGR
Texas Instruments — Power Management & Signal Chain
Product Overview
The DRV8210DSGR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
DRV8210DSGR: 11 V H-bridge motor driver with three control interfaces in a 2 mm WSON
DRV8210DSGR is a single H-bridge in the eight pin DSG body that runs from 1.65 V to 11 V, integrates one ohm of combined switch resistance, delivers 1.76 A peak in a full bridge and accepts PWM, phase and enable, or half bridge control on the same pins in a WSON body of 8 pins. The DRV8210 drives a brushed DC motor, a latching relay, a solenoid or an LED load from a supply as low as 1.65 V and as high as 11 V. The four internal switches total one ohm, the full bridge peak output is 1.76 A, and two outputs in parallel reach 3.52 A. The device is offered in an eight pin WSON and a six pin SOT-563, and the control pins can be configured for PWM, phase and enable, or independent half bridge operation.
Order code and package
| Order code | DRV8210DSGR |
| Function | single H-bridge motor driver |
| Operating supply voltage | 1.65 V to 11 V |
| Combined switch resistance | 1 ohm |
| Peak output, full bridge | 1.76 A |
| Peak output, half bridge | 1.76 A per output |
| Peak output, parallel half bridge | 3.52 A |
| Logic inputs | 1.8 V, 3.3 V and 5 V compatible |
| Package | eight pin WSON, DSG body |
| Sibling package | six pin SOT-563, DRL body |
Electrical parameters that decide the application
| Junction to top characterization parameter, WSON | 13.9 C per W |
| Junction to board characterization parameter, WSON | 66.2 C per W |
| Junction to top characterization parameter, SOT-563 | 2.0 C per W |
| Junction to board characterization parameter, SOT-563 | 40.0 C per W |
| Sleep mode supply current at 5 V | quoted with both inputs low after the sleep delay |
| Control interfaces | PWM, phase and enable, and half bridge |
| Loads supported | brushed motor, latching relay, solenoid, LED string |
| Supply range for a single cell | down to 1.65 V |
Points to check before this part goes on a BOM
One ohm of combined switch resistance is the whole thermal story at these currents. At 500 mA the bridge drops 0.5 V and dissipates 0.25 W, at 1 A it drops 1 V and dissipates 1 W, and at the 1.76 A peak it dissipates 3.1 W. On a two cell supply that 1 V drop is a sixth of the rail, so a motor that is specified at 3 V sees 2 V and turns slower, and the loss that produced the drop is inside an eight pin WSON.
The three control schemes are a pin count decision. A controller with one PWM channel can drive the bridge with a single pin and let the internal timing decide the direction changes; a controller with two spare pins can use phase and enable, which gives independent control of direction and magnitude; and a controller that needs two independent half bridges, for two motors or a latching relay, uses the same pins differently. The mode is a configuration rather than a part number, so the same order code covers all three.
The 1.65 V minimum supply is what makes this a single cell part. Below about 2 V the switch resistance dominates and the available current falls, so a motor that runs at 1.76 A from 5 V will not run at 1.76 A from 1.8 V; the bridge will current limit or the supply will sag. The honest way to use the low end of the range is with a load that needs a few hundred milliamps, and to treat the 1.76 A figure as belonging to the 5 V end of the range.
Paralleling the two half bridges for 3.52 A is a thermal decision as much as an electrical one. Two outputs in parallel halve the resistance to 0.5 ohm, so at 2 A the drop is 1 V and the dissipation is 2 W, which is still a lot for an eight pin WSON. The mode exists for a short burst, such as a lock or a latch that has to be driven hard for a hundred milliseconds, and not for a continuous motor load.
The WSON body has a junction to board parameter of 66.2 C per W and a junction to top parameter of 13.9 C per W, which is an unusual ratio and it means the top of the package is a better path than the board. On a small board with little copper that is welcome, and it also means a part that is pressed against a housing or potted will behave differently from one in free air. The SOT-563 version of the same die shows the opposite ratio, with 2.0 C per W to the top and 40.0 C per W to the board, so the two packages cannot be treated as interchangeable in a thermal calculation.
Sleep mode is a real state and not a software courtesy. With both inputs low the bridge goes high impedance and the supply current falls to the sleep figure after a delay, so a battery product that holds a mechanism still for most of its life spends that time in the lowest state the part offers. The delay matters: a controller that pulses the inputs every few milliseconds to check for a stall never lets the device reach sleep, and the average current is then set by the active state rather than by the sleep specification.
The loads this part can drive go beyond motors, and the data sheet lists them because the bridge does not care what the load is. A latching relay needs a pulse of one polarity to set and the other to reset, which the bridge delivers directly; a solenoid needs a current and a flyback path, which the internal diodes provide. An LED string on a bridge output can be driven either way for a two colour indicator, and the PWM input then sets the brightness. The limit in every case is the one ohm and the thermal path, not the load type.
Where this order code fits
This order code belongs on battery powered mechanisms: camera and lens shutters, drug delivery pumps, portable printer feeds, electronic locks, valve actuators and wearable haptics, where the rail is a single lithium cell or a 5 V USB supply. It is chosen when the controller has few spare pins, because the same three inputs cover three different control schemes and a single PWM pin can run the bridge on its own. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Medical Device Components page.
Questions buyers ask
How much current can this driver hold continuously? It depends on the copper and the ambient more than on the rating. One ohm at 1 A is 1 W, and the WSON junction to board path of 66.2 C per W turns that into a 66 C rise unless the board spreads it. A continuous 500 mA is comfortable on most boards, 1 A needs copper under the pad, and 1.76 A is a peak rating for short events rather than a continuous figure.
Can it drive two motors? It can drive two unidirectional loads, each on one half bridge, or two independent half bridges for a latching relay. It cannot drive two bidirectional motors, because the four switches form one bridge. A second device is the answer for two bidirectional loads, and the six pin version is the smaller option when the second motor is small.
Does the supply range really go down to 1.65 V? The device operates from 1.65 V, and the useful current at that voltage is much lower than at 5 V because the one ohm of switch resistance is a larger fraction of the rail. A 1.65 V supply into a 1 ohm load can deliver about 0.8 A before the drop equals the supply, so the low end of the range suits light loads and not the peak rating.
Why does the package choice change the thermal numbers so much? The two bodies are the same die in different packages with different heat paths. The WSON conducts better into the board and worse into the air above it; the SOT-563 is the reverse. On a board with little copper the WSON figure is more useful, and on a board with a large ground plane the difference narrows. The numbers belong to the package, not to the part.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Component Lead Time Solutions page sets out the checks that keep a substitute from failing on the bench.