DRV5053VAQLPG
Product Specifications
DRV5053VAQLPG
Texas Instruments — Power Management & Signal Chain
Product Overview
The DRV5053VAQLPG from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
DRV5053VAQLPG: the 90 mV per mT analog sensor in a TO-92
The DRV5053VAQLPG is the highest sensitivity option in the DRV5053 analog family, at 90 mV per mT with a 1 V quiescent output. Put simply, a 8 mT field is enough to drive the output from 1 V to about 1.7 V, which means the part can read a small magnet at a distance where the other options would still be sitting near the quiescent point.
That sensitivity is what makes it useful in a handheld or a compact mechanism, where the magnet is a 3 mm disc and the air gap is set by a plastic wall rather than by a machined bracket. It is also what makes it unforgiving: the linear window is about 9 mT wide, so a magnet brought closer than the intended position clips the output and the reading stops tracking.
The body is the TO-92 with no reel letter, which on this family means a 1000 piece bulk bag rather than a strip. The electrical behaviour is the family standard: 2.5 V to 38 V supply, 1.8 kHz bandwidth, 35 us power-on time, and a Q grade from minus 40 C to plus 125 C.
Key data for the DRV5053VAQLPG
| Output | Analog, 0.2 V to about 1.8 V, 1 V at zero field |
| Sensitivity | Minus 90 mV per mT, the highest in the family |
| Field range | About 9 mT before the output reaches its limit |
| Supply | 2.5 V to 38 V, no regulator, reverse protection to 22 V |
| Supply current | 2.7 mA typical at 25 C, 3.0 mA typical at 125 C |
| Bandwidth | 1.8 kHz, the family figure |
| Temperature | Minus 40 C to plus 125 C on the Q grade |
Body, packing and marking data
| Body | TO-92, three pins, LPG outline |
| Packing | 1000 pieces in bulk without a reel letter, 3000 in ammo with M |
| Finish | Tin lead finish, moisture level not applicable to this body |
| Marking | ALVA on the flat face, which identifies the VA die |
What the code leaves out, and why it matters
DRV5053 is the family, VA is the 90 mV per mT option, Q is the temperature grade, LPG is the TO-92 body, and there is no reel letter at the end. On this family the absence of a letter is a 1000 piece bulk bag, R is a 3000 piece reel in SOT-23, T is a 250 piece reel and M is a 3000 piece ammo pack.
On the addendum this exact string is printed as an active row with the quantity column reading call TI, which means the vendor is not quoting a stocked packing quantity for it. That is not the same as obsolete, but it does mean a schedule cannot be confirmed from the document alone, and an order should be placed against a written quantity rather than an assumed bag size.
The second thing to settle is the slope direction. VA is a negative sensitivity option, so a south pole at the marked face pulls the output below 1 V. A board that reads a rising voltage as increasing travel will run backwards, and the error shows up as a position reading that decreases when the mechanism extends.
Where the highest sensitivity is the right answer
Small magnets, wide plastic gaps, and mechanisms where the travel is only a few millimetres are the natural home for a 90 mV per mT part. Gamepad triggers, pedals, keyboard and instrument controls, and tilt or weight measurement all appear on the vendor application list for this family.
When the sensor has to move to a smaller body, the pin to pin cross reference page sets out the sensitivity steps between the five analog options, and the strategic sourcing page covers how to keep a single die family qualified across two bodies.
Questions we get on this code
Can the VA option read a magnet at 20 mm? In principle yes, but the field at that distance from a small disc is often below 1 mT, and 90 mV per mT gives 90 mV of signal on a 1 V offset, which is a difficult measurement on a noisy rail. At that gap a larger magnet is the better engineering answer than a more sensitive sensor.
What happens at the ends of the travel? The output clamps near 0.2 V and 1.8 V, and the data sheet is clear that the linear region ends there. A controller that assumes linearity beyond the clamp will read a stuck position as a mechanical stop, and the diagnostic will point at the mechanism rather than at the sensor range.
The other practical question is the bulk bag. A 1000 piece bag of TO-92 parts is fine for a hand build, but the leads arrive with a slight spread and the first operation on the line is usually a straightening jig. Ordering the ammo version for any build above a few hundred pieces costs less than the labour of straightening leads, even though the part number is one letter longer.