DRV5032FDLPGM
Product Specifications
DRV5032FDLPGM
Texas Instruments — Power Management & Signal Chain
Product Overview
The DRV5032FDLPGM from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
DRV5032FDLPGM: a 4.8 mT push-pull switch in the TO-92 body
The DRV5032FDLPGM is the through-hole member of the low power DRV5032 switch family, packed in the three pin TO-92 with 3000 pieces in ammo. It uses the FD version of the die, a 4.8 mT threshold part with a push-pull output sampled at 20 Hz, and the supply window runs from 1.65 V to 5.5 V.
The FD option differs from the FA option in one respect that matters on a real board: it drives the output in both directions. A pull up resistor is not needed, and the output cannot be pulled to an undefined level by a controller input that sources a small current. On a through-hole assembly with a flying lead to a panel sensor, that is one fewer component to fit and one fewer joint to inspect.
The 20 Hz sample rate is the constraint to check against the mechanics. The part looks at the field once every 50 ms, so a lid that opens and closes in 20 ms will not be seen. Average current at that rate is 1.3 uA, which is why this part ends up in products that run from a coin cell for years.
Key data for the DRV5032FDLPGM
| Output | Push-pull, active drive high and low, no pull up needed |
| Threshold | 4.8 mT maximum operate point on the FD option |
| Sampling rate | 20 Hz, one reading every 50 ms |
| Supply | 1.65 V to 5.5 V, which covers a single lithium cell directly |
| Supply current | 1.3 uA average on the 20 Hz versions, 0.54 uA on the 5 Hz versions |
| Temperature | Minus 40 C to plus 85 C |
| Output drive | Push-pull stage that needs no external component on the output |
Body, packing and marking data
| Body | TO-92, three pins, LPG outline for through-hole assembly |
| Packing | 3000 pieces in ammo pack on the M suffix |
| Finish and moisture | Tin lead finish, moisture level not applicable to this body type |
| Marking | 32FD on the flat face, which identifies the FD die family |
What the code tells you
DRV5032 is the family, FD is the version, LPG is the TO-92 body, M is the ammo pack. The same die is published in the SOT-23 and, for some versions, in the X2SON, so the body letter is the only field that separates a through-hole order from a surface mount one. A purchase order that names DRV5032FD without the body letters can be filled in any of them.
The family divides by threshold first and output type second. DG and DU sit at 3.4 and 3.9 mT, FA, FB, FC and FD at 4.8 mT, AJ at 9.5 mT and ZE at 63 mT for strong field work. Of that set, FC and AJ and ZE have open drain outputs and the rest are push-pull, so a board that needs to share one interrupt line between several sensors has to pick from the open drain group.
The addendum prints the LPG rows as active in both 1000 piece bulk and 3000 piece ammo, and it prints no obsolete row for this body, which is worth noting because two of the X2SON rows in the same family already carry an obsolete status.
Where the through-hole version earns its place
Panel sensors on a flying lead, retrofits into an existing through-hole assembly, and any product where the sensor is hand fitted after the board has been potted are the cases that keep the TO-92 alive. The 4.8 mT threshold also suits a small ferrite magnet at a few millimetres, which is what a low cost lid sensor usually has.
For boards that mix this switch with other position sensing, the incoming inspection plan page sets out the field check that catches a wrong version on the reel, and the kitting service page covers how a mixed through-hole and surface mount kit is kept together for a small build.
Questions we get on this code
Can the push-pull output drive a controller input directly? Yes, within the current the output stage can source and sink, and without a pull up. The difficulty appears when two sensors are wired to one input: push-pull stages fight each other and one of them will be asked to sink the other's source current. In that case the open drain versions of the family are the right choice.
Is the 85 C limit a problem in a panel? Usually not, but a sensor mounted next to a power supply or a lamp ballast can sit well above ambient. The rating is on the ambient around the package, not on the room, and a TO-92 on a lead has very little copper to help it.
A third question is about the ammo strip. A cut strip of 50 pieces is normal for a trial build, but the parts are then loose in a bag and the lead spacing is easily bent. Keep the strip intact until the parts reach the insertion station, and check the lead pitch against the hole pattern before the first board.