DRV5032FADMRR
Product Specifications
DRV5032FADMRR
Texas Instruments — Power Management & Signal Chain
Product Overview
The DRV5032FADMRR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
DRV5032FADMRR: the 4.8 mT switch in the 1.5 mm X2SON
The DRV5032FADMRR is the smallest body in the DRV5032 family: a four pad X2SON measuring 1.5 mm by 1 mm, with the FA threshold at 4.8 mT and a push-pull output sampled at 20 Hz. It occupies less board area than the SOT-23 it replaces and needs no pull up resistor, which is the point of the push-pull option.
A push-pull output drives both ways, so the part sources current into a controller input instead of only sinking it. On a board where the sensor sits next to the microcontroller this removes a component and a leakage path, and it removes the question of what the input does when the sensor is unpowered: the output goes low impedance in both directions and the controller sees a defined level.
Average current is 1.3 uA at 20 Hz, the supply window is 1.65 V to 5.5 V, and the operating range stops at 85 C rather than the 125 C of the older Hall parts. For a wearable or a handheld that is not a limitation; for anything near a motor or an engine it is.
Key data for the DRV5032FADMRR
| Output | Push-pull, drives high and low, no external pull up |
| Threshold | 4.8 mT maximum operate point on the FA option, omnipolar response |
| Sampling rate | 20 Hz, one field reading every 50 ms |
| Supply current | 1.3 uA average, 0.54 uA on the 5 Hz versions of the family |
| Supply | 1.65 V to 5.5 V, no regulator needed from a single cell |
| Temperature | Minus 40 C to plus 85 C |
| Body size | X2SON, four pads, 1.5 mm by 1 mm |
Body, packing and marking data
| Body | X2SON, four pads, the DMR outline |
| Packing | 3000 pieces on a large reel |
| Finish and moisture | Tin lead finish, moisture level 1 at 260 C, unlimited floor life |
| Marking | 2FA on the package, which is the only visible identifier at this size |
What to watch in the order code
The code is DRV5032, FA version, DMR body, R reel. The DMR body is the one to check on the addendum, because the same FA threshold is also published in the SOT-23 and the TO-92, and the three rows carry different quantities. The X2SON row is 3000 pieces on a large reel, the same as the SOT-23, so a reel count alone does not tell you which body arrived.
The second trap is the A revision. The addendum prints DRV5032FADMRR as active and DRV5032FADMRR.A as obsolete, and the two are one character apart in a bill of materials. Whichever string was qualified is the one to keep, and the obsolete row should be treated as a last time buy rather than a drop in replacement.
Third, the four pad body has no exposed thermal pad and no orientation mark beyond the die marking, so the pick and place data has to be checked against the vendor drawing rather than against a photograph. At 1.5 mm by 1 mm a rotated part still fits the pads and simply reads the wrong field direction.
Where the X2SON body pays for itself
Hearing instruments, wearables, phone and tablet lids, meter tamper detection and any board where the sensor has to sit at the edge of a flex are the applications that justify the small body. The push-pull output also suits a direct connection to a low power microcontroller pin that has no pull up configured.
For products where the same board carries an inertial sensor as well, the IMU selection guide explains when a Hall switch beats an accelerometer for lid detection, and the how to verify a drop in replacement page covers the footprint and field checks before a smaller body is swapped in.
Questions we get on this code
Does the push-pull output work with a controller that expects an open drain? Not directly. Two push-pull outputs on one node fight, and a push-pull driving a node that a controller also drives will source current into the controller. If the receiving circuit was built around an open drain sensor, the FA push-pull part needs a series resistor or a different version.
Why does this part stop at 85 C when the SOT-23 versions go to 125 C? Because the die is the same but the package is not: the smaller body has less copper to spread heat and the vendor rates it lower. On a board that reaches 90 C at the sensor the part is outside its rating even though the junction may still be inside the silicon limit.
The last point is about the reel. At 3000 pieces on a 180 mm reel the part is easy to lose on a line that runs small batches, and the X2SON body has no room for a date code. A reel label and a bag label that travel with the parts matter more at this size than at any other, because the body itself carries only the die marking.