DRV5011ADYBHR
Product Specifications
DRV5011ADYBHR
Texas Instruments — Power Management & Signal Chain
Product Overview
The DRV5011ADYBHR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
DRV5011ADYBHR: a 0.8 mm latch for a wearable size board
The DRV5011ADYBHR puts the same latch die into a four ball wafer level package measuring 0.80 mm by 0.80 mm. On a board where the sensor sits behind a display, inside a hinge or under a small motor, the body size decides whether the part can be placed at all, and this is the smallest body in the family. Sensitivity, hysteresis and bandwidth are unchanged at plus or minus 2 mT typical, about 4 mT and 30 kHz.
What changes is the assembly discipline. A four ball package with a 0.4 mm pitch needs a stencil, a placement accuracy and a reflow profile that a three pin SOT-23 does not. It also has no lead frame to absorb thermal expansion, so the board material and the copper balance under the part matter more than they do for a leaded body. Boards that pass with the SOT-23 sometimes fail with the wafer level part for reasons that have nothing to do with magnetics.
Packing is 3000 pieces in ammo pack, which is a different carrier from the reel used by the SOT-23 row. The marking is a single letter, so the only way to tell two parts apart at goods inwards is the label on the carrier, not the body. That is worth writing into the incoming inspection instruction for this string.
Key data for the DRV5011ADYBHR
| Type | Digital latch, toggles on alternating north and south poles |
| Sensitivity | Operate point plus or minus 2 mT typical, about 4 mT of hysteresis |
| Supply | 2.5 V to 5.5 V, no external regulator required |
| Output | Push pull CMOS, 5 mA source and 20 mA sink, no pull up needed |
| Bandwidth | 30 kHz sampling rate |
| Body size | 0.80 mm by 0.80 mm, four balls at a 0.4 mm pitch |
Body, packing and marking data
| Body | DSBGA YBH, 4 balls, 0.80 mm by 0.80 mm |
| Packing | 3000 pieces in ammo pack on the plain row, marking a single letter |
| Finish | SNAGCU ball material, moisture level recorded as not applicable for this package type |
| Temperature | Minus 40 C to plus 125 C on the row that carries this string |
Order code note before you place the string on a purchase order
The addendum for this family has a status column that does not line up with the string on the row. The plain DRV5011ADYBHR row is printed as active production in ammo pack, while the lettered row directly under it prints a large tape and reel carrier and is marked obsolete. The carrier and the status have swapped places between the two rows, and a buyer reading only the obsolete flag will conclude the part is dead when it is not.
The temperature column on this row is also blank in the printed table while the surrounding rows print minus 40 C to plus 125 C. Treat 125 C as the window for the body and confirm it on the vendor record rather than assuming the surface mount row at 135 C applies, because the two bodies do not share the same test flow.
Where the smallest body earns its place
Wearable hinges, camera modules, small motor end caps and any board where the sensor has to sit within a millimetre of a magnet use this package. The part is also used where the board itself is the constraint, such as a flexible circuit that cannot take a leaded part or a rigid section that has no room for a three pin land pattern.
Small bodies concentrate the sourcing risk, because fewer suppliers hold them and the carrier format is less common. Our component lead time solutions page covers how a small package shortage is handled without a board change, and the kitting service page is the one to read when a build needs the sensor, the magnet and the connector to arrive together.
Questions we get on this code
The first question is whether the wafer level body needs a different reflow profile. It does not need a different peak, but it needs tighter control of the ramp and of the soak, because there is no lead frame to absorb the mismatch between the die and the board. A profile borrowed from a leaded part usually works and occasionally cracks a corner ball.
The second question is about inspection. A single letter marking on a 0.8 mm body cannot be read reliably under a microscope after reflow, so the carrier label and the reel count are the only traceable evidence. Photograph the label at goods inwards and keep it with the build record, because a mixed bag of two latch grades looks identical once it is on the board. A warranty claim three months later will ask which lot the sensors came from, and only the carrier label answers that.