Contact Us

DRV5011ADDBZR

Brand: Texas Instruments
Texas Instruments DRV5011ADDBZR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

DRV5011ADDBZR — Power Management & Signal Chain | Superb Automation

DRV5011ADDBZR

Texas Instruments — Power Management & Signal Chain

Product Overview

The DRV5011ADDBZR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

DRV5011ADDBZR: a low voltage latch in a three pin SOT-23

The DRV5011ADDBZR is a digital latch Hall effect sensor that runs from 2.5 V to 5.5 V, which puts it on the same rail as a modern microcontroller without a regulator in front of it. A south pole above the package drives the output low when the flux passes the operate point, and the output stays low until a north pole takes the flux back past the release point. Alternating poles are what toggle the output, which is exactly the sequence a rotating magnet produces.

Sensitivity is plus or minus 2 mT typical, with 4 mT of hysteresis between the operate and release points. That hysteresis is the number that decides whether a latch is usable in a real motor: too little and the output chatters at the edge of the magnetic field, too much and the magnet has to be larger or closer. Sensing bandwidth is 30 kHz, which covers a rotor turning fast enough that mechanical commutation has stopped being an option.

The output is push pull, capable of sourcing 5 mA and sinking 20 mA, and it needs no pull up resistor. That saves a component per channel and removes the question of what rail the pull up sits on when the sensor runs at 3.3 V and the controller at 1.8 V. The part is specified over minus 40 C to plus 135 C, which is wider than most of the board around it.

Key data for the DRV5011ADDBZR

TypeDigital latch, toggles on alternating north and south poles
SensitivityOperate point plus or minus 2 mT typical, with about 4 mT of hysteresis
Supply2.5 V to 5.5 V, no external regulator required
OutputPush pull CMOS, 5 mA source and 20 mA sink, no pull up needed
Bandwidth30 kHz sampling, which sets the maximum electrical commutation rate
TemperatureMinus 40 C to plus 135 C on the SOT-23 row

Body, packing and marking data

BodySOT-23 DBZ, 3 pins, 2.92 mm by 1.30 mm
Packing3000 pieces on a large reel, 180 mm carrier, marking 1AD
FinishTin plated, moisture level 1, 260 C peak, unlimited floor life
TemperatureMinus 40 C to plus 135 C as printed on the SOT-23 row of the addendum

Order code note before you place the string on a purchase order

Three bodies share this die and the temperature columns do not agree across them. The SOT-23 row prints minus 40 C to plus 135 C, and the TO-92 and DSBGA rows of the same family print minus 40 C to plus 125 C. The difference is not a marketing slip, it is the package and the test flow, and a board specified at 130 C has to use the surface mount body.

The letter after DRV5011 is the grade and the sensitivity band rather than a package code, and the package comes from the three letters before the reel suffix. Reading the code from the right is the reliable habit here: R is the large reel, DBZ is the SOT-23, and what remains identifies the device.

Where a low voltage latch earns its place

Brushless dc motors use three of these to read rotor position, and the same part does incremental encoding for a knob, a wheel, a flow meter or a mechanical travel limit. The 2 mT sensitivity suits a small diametric magnet on a shaft, and the 30 kHz bandwidth covers a motor turning faster than a hall sensor with a 1 kHz sample rate could follow.

Rotor position sensing is one of the few places where a second source has to match the magnetic thresholds rather than just the pinout, because a part with a 6 mT operate point will not trigger from the magnet the first part was chosen for. Our pin to pin cross reference page covers the electrical comparison, and the safety stock planning page is the one to read when a motor line cannot stop for a sensor.

Questions we get on this code

The first question is whether a latch can replace a switch. It cannot without a change of magnet arrangement, because a latch holds its state when the field is removed and a switch does not. A door sensor built around a latch will report open and stay open, which looks like a controller fault and is a magnetics fault.

The second question is about the magnetic axis. The sensing element responds to flux perpendicular to the top of the package, so a magnet sliding past the side of the package produces a much weaker signal than one passing over the top. The vendor draws the active area on the package drawing, and a millimetre of offset is worth more than a grade of sensitivity. A three pin latch also has no orientation pin beyond the body shape, so the assembly drawing has to show which face is the sensing face.