DRV103H
Product Specifications
DRV103H
Texas Instruments — Power Management & Signal Chain
Product Overview
The DRV103H from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
DRV103H: a 3 A PWM low side driver for solenoids, valves and heaters
The DRV103H is the high current member of the DRV103 pair, a low side DMOS switch with a pulse width modulated output and its own oscillator. The H suffix is the PowerPAD small outline body, which carries the exposed metal pad that lets the part hold 3 A, against 1.5 A in the plain body. Supply range is 8 V to 32 V, and the output stage sits between the load and ground, so the load is tied to the positive rail and the part pulls its return.
What makes the part useful on a valve or a solenoid is the internal timing. A digitally controlled input switches the output on, an external capacitor on the delay pin sets how long the output stays fully on before the oscillator takes over, and two resistors set the frequency and the duty cycle. That gives a peak and hold profile from three passive parts: full current to pull an armature in, then a lower duty cycle to hold it there without heating the coil.
Protection is on chip. Current limit and thermal shutdown both operate the same open drain flag, so a controller can tell that the output has been interrupted rather than assume the load failed. The oscillator covers 500 Hz to 100 kHz, and the part is specified over minus 40 C to plus 85 C. Quiescent current is around 0.4 mA, which is small enough that a bank of drivers can stay biased while the rest of the board sleeps.
Key data for the DRV103H
| Output | Low side DMOS switch, 3 A in the PowerPAD body, 1.5 A in the plain SO-8 body |
| Supply | 8 V to 32 V operating |
| Modulation | Internal oscillator adjustable from 500 Hz to 100 kHz, duty cycle from 10 to 90 per cent |
| Timing | External capacitor sets the DC to PWM delay, up to about 5.5 ms with 0.1 uF |
| Current limit | Folded back limit in the 3.4 A to 3.8 A region across temperature on the 3 A body |
| Protection | Thermal shutdown near 160 C with reset around 140 C, over current shutdown, open drain OK flag |
| Current draw | 0.4 mA quiescent, plus the load current through the switch |
| Input | Digital control pin, TTL and CMOS compatible |
Body, packing and marking data
| Body | SO PowerPAD DDA, 8 pins, with the exposed pad that carries the 3 A rating |
| Packing | 75 pieces in a tube on the plain string, 2500 pieces on a large reel as DRV103H/2K5 |
| Finish | Tin plated, moisture level 1, 260 C peak, unlimited floor life on the reel row |
| Temperature | Minus 40 C to plus 85 C on every published row |
Order code note before you place the string on a purchase order
The string on this page is the tube row, and its status and finish columns are blank in the addendum while the row directly beneath it carries the data. The reel string is DRV103H/2K5 at 2500 pieces, and that row is printed as active production with tin plating and moisture level 1. If the build is a prototype, the tube is fine. If the build is a run, order the reel string and do not expect the bare DRV103H to arrive on tape.
The other letter to keep straight is U against H. DRV103U is the plain small outline body at 1.5 A and DRV103H is the PowerPAD body at 3 A. Both are eight pin parts with the same pinout, so a substitution in either direction fits the board and changes the current the output can hold, which is exactly the kind of swap that survives a prototype and fails in the field.
Where a PWM low side driver earns its place
Solenoid valves, relay coils, contactor coils, heaters, lamps and thermoelectric coolers all share one property: they need more current to pull in than to hold. A driver with an internal oscillator and an adjustable delay gives that profile without a microcontroller pin tied up in a timer, and it keeps working while the controller is in a reset or a low power state.
This is an old part with a long production history, and boards that were built around it are still in service, which is why it turns up in maintenance and re order work more than in new work. Our obsolete part cross reference hub collects the parts that sit in that position, and the component obsolescence management page covers how to keep a last time buy from turning into a board revision.
Questions we get on this code
The first question is always about the flyback path. A solenoid is an inductor, and the DRV103 has no integrated clamp, so the board needs a diode from the output to the positive rail, rated above the supply and fast enough for the switching frequency. Without it the switch sees the coil energy on every turn off, and the failure mode is a shorted output rather than an open one.
The second question is audible noise. The oscillator can be set anywhere from 500 Hz to 100 kHz, and anything inside the audible band will sing. A valve that buzzes is usually a valve driven near 1 kHz to 3 kHz, and the cure is to raise the frequency above the band and accept a little more switching loss in the switch.