Contact Us

CC2674P106T0RSKR

Brand: Texas Instruments
Texas Instruments CC2674P106T0RSKR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

CC2674P106T0RSKR — Power Management & Signal Chain | Superb Automation

CC2674P106T0RSKR

Texas Instruments — Power Management & Signal Chain

Product Overview

The CC2674P106T0RSKR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

CC2674P106T0RSKR: plus 20 dBm from the die, in an 8 mm by 8 mm body

CC2674P106T0RSKR is the 8 mm by 8 mm VQFN64 member of the CC2674P10 family, a high performance multiprotocol 2.4 GHz wireless microcontroller with an Arm Cortex-M33 core at 48 MHz, 1 MB of flash and 256 KB of SRAM. The letter P in the family name is the integrated power amplifier, and it is the whole point of this string: the part puts out plus 20 dBm without an external amplifier stage.

The RSK suffix is the 64 pin body with 42 general purpose pins, and the T0R suffix is the reel and revision. Compared with the RGZ body of the same die, the larger package buys 16 more pins, which for a product with a display, a keypad, two serial ports and a radio front end is the difference between one board and two.

The values below come from SWRS269B, revised February 2025, and from the orderable addendum. They matter most in three places: the thermal path at plus 20 dBm, the sensitivity on the coded PHY, and the supply current during a transmit burst, because a 102 mA burst is what decides the decoupling and the regulator.

What the integrated amplifier changes on the board

A discrete plus 20 dBm stage on a 2.4 GHz radio is a power amplifier, a harmonic filter, a receive bypass switch, a directional coupler or a detector, and a matching network, all of which have to be tuned and all of which take board area and test time. The CC2674P10 integrates the amplifier and keeps the harmonic performance inside the specified envelope, so the board carries an antenna matching network and nothing else on the transmit side. That is a shorter bill of materials and a shorter radio test.

The cost of the integration is heat, and the heat is not small. At plus 20 dBm the part draws 102 mA, so on a 3.3 V rail the input power is 337 mW against 100 mW of radio output, and about 237 mW becomes heat inside an 8 mm by 8 mm body. That is fine for a burst and it is not fine for a continuous transmitter, which is why the family is specified for packet radios and not for a continuous wave source.

Functionmultiprotocol 2.4 GHz wireless microcontroller with integrated power amplifier
CoreArm Cortex-M33, 48 MHz, TrustZone, floating point and DSP extension
Flash1024 KB program memory
SRAM256 KB ultra-low leakage with parity, plus 32 KB if parity is disabled, plus 8 KB cache
ProtocolsThread, Zigbee, Matter, Bluetooth 5.3 Low Energy, IEEE 802.15.4, 6LoWPAN
Frequency band2400 MHz to 2480 MHz
Output powerup to plus 20 dBm with temperature compensation
Receiver sensitivityminus 105 dBm for Bluetooth Low Energy 125 kbps, minus 105 dBm for 802.15.4 OQPSK
Receive current6.4 mA at 2.4 GHz
Transmit current6.9 mA at 0 dBm, 25 mA at plus 10 dBm, 102 mA at plus 20 dBm
Active current4.0 mA in CoreMark, 83 microamps per MHz
Standby current1.19 microamps with RTC and 256 KB retention
Shutdown current0.13 microamps, wake on pin
Supply range1.8 V to 3.8 V, on-chip buck converter
Analog12-bit SAR ADC at 200 kSamples per second, 8 bit DAC, two comparators
Serialfour UART, four SPI, two I2C, one I2S
Securitysecure boot, secure key storage, TrustZone, AES 128 and 256 bit, public key accelerator, SHA2, TRNG
PackageVQFN64, RSK, 8 mm by 8 mm, 42 GPIO
Ambient rangeminus 40 to plus 105 degrees Celsius
Carrierlarge tape and reel

Thermal arithmetic at three power levels

At 0 dBm the part draws 6.9 mA, about 23 mW on a 3.3 V rail, and the die stays within a degree of the board. At plus 10 dBm it draws 25 mA, 82 mW input for 10 mW of output, so about 72 mW of heat. At plus 20 dBm the heat is 237 mW. In a body with a thermal pad the junction rise at 237 mW is on the order of 20 degrees above the board, which a 105 degree ambient turns into 125 degrees junction. That is inside the limit and it leaves nothing for a poor thermal connection, which is the practical argument for a solid ground plane under the pad and vias through it.

The burst nature of the traffic is what makes the arithmetic acceptable. A sensor that transmits a 30 byte packet at plus 20 dBm spends about 1 ms in the burst, so the average heat is a fraction of a milliwatt, and the junction follows the average rather than the peak because the thermal time constant is milliseconds. A product that streams continuous data at plus 20 dBm needs a different conversation, and it usually ends with a lower power setting and a better antenna.

Sensitivity and the long range claim

Minus 105 dBm on the 125 kbps coded PHY combined with plus 20 dBm of output gives a link budget of 125 dB, which is roughly 10 dB more than a plus 5 dBm part and translates into about three times the range in free space. That is the number a customer is buying when they choose this string for a warehouse, a meter room or a farm, and it is the number to check against the antenna gain, because a poor antenna can give back the whole 10 dB.

The 802.15.4 sensitivity of minus 105 dBm with the coherent modem is worth noting separately. A Thread or Zigbee network built on this part does not need a plus 20 dBm setting to reach the same distance, so the amplifier is a tool for the marginal link rather than the default, and a network that runs every node at plus 20 dBm will interfere with itself in a dense installation.

TrustZone and secure boot in a connected product

The M33 core carries TrustZone, which lets a product split firmware into a secure world that holds keys and a normal world that runs the application and the network stack. Secure boot checks the image before it runs, secure key storage keeps the private key out of flash reads, and anti-rollback stops a downgrade attack that would otherwise reinstate a known vulnerable image. For a product that will be installed in a building for ten years, those features are the difference between a firmware update programme and a recall.

The public key accelerator and the SHA2 engine matter for the same reason at a smaller scale: a Thread or Matter commissioning step that has to verify a certificate chain in under a second needs hardware assistance, and a software implementation on a 48 MHz core makes commissioning feel broken to the installer.

Where this part fits

The applications list in the document names building security, HVAC, fire safety, video surveillance, elevators, medical patient monitoring, electronic shelf labels, access points and portable remotes. In our own builds the plus 20 dBm part appears where the antenna is inside a metal enclosure or where the node is at the edge of a plant, and the plus 5 dBm parts appear everywhere else. A customer who asks for the amplifier usually has a range problem that a better antenna would also solve, and the honest comparison is cost against installation time.

For a medical device the secure boot and the 105 degree window are the two lines that matter, and the medical device component page collects the parts we keep for that class of build. For a radio product the antenna and the front end decide more than the core, and the RF component sourcing page covers the passives and the filters that go beside it.

Ordering and incoming checks

The orderable row prints the string as active and in production, VQFN64 with 8 mm by 8 mm body, large tape and reel, and a moisture level that should be read from the addendum before the reels are opened. The RSK body is the larger of the two packages for this die, and a purchase order that names only the family can be filled with the 7 mm body, which will not fit the land pattern.

Incoming inspection should include a transmit power check at the top setting on a sample, because the amplifier is the one block that cannot be verified from a label. A reel that transmits at plus 10 dBm when the firmware asks for plus 20 dBm is either a different part or a damaged die, and both are worth catching before the board is built.

For a build that needs the module, the antenna and the passives together, the one stop BOM sourcing route keeps the RF chain on one line, which matters because the matching network values depend on the antenna chosen and the two should not be ordered from different places.

Three questions buyers ask about this string

Do we still need an external amplifier? No for plus 20 dBm. The integrated stage covers the regulatory limited power, and an external stage on top would break the harmonic and spurious limits rather than improve them.

Why choose the 64 pin body over the 48 pin one? Only for pins. The radio, the memory and the core are the same, so unless the board needs the extra 16 pins the smaller body is cheaper and easier to route.

Is the 102 mA burst a problem for a coin cell? Yes. A CR2032 cannot supply a 102 mA pulse without a large capacitor, so a plus 20 dBm node needs a bulk capacitor of at least a few hundred microfarads or a different cell chemistry. At 0 dBm the same node runs from a coin cell without difficulty.