BQ79656PAPRQ1
Product Specifications
BQ79656PAPRQ1
Texas Instruments — Power Management & Signal Chain
Product Overview
The BQ79656PAPRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
BQ79656PAPRQ1: a sixteen cell automotive monitor with the protector inside
The BQ79656PAPRQ1 is a battery monitor for automotive packs, covering six to sixteen cells in series, with cell balancing, current sense and a hardware protector in the same package. It is qualified to AEC-Q100 grade 1 for minus 40 to 125 C ambient, and it is developed for functional safety applications with systematic capability up to ASIL D.
The measurement chain is the reason the part exists. Cell voltages are converted with plus or minus 1.5 mV of accuracy, and the conversion of a full stack takes less than 200 microseconds, so a pack can be measured while a motor is drawing current without the readings being smeared by the load. Post ADC filters on each channel give a settled, DC like result rather than an averaged one.
Communication is a daisy chain across an isolation barrier, which is how a stack of these devices talks to one host without a separate wire pair per device. The part also provides a 5 V output to power the digital isolator on the board and a built in SPI master for devices on the same side of the barrier.
Key data for the BQ79656PAPRQ1
| Function | Cell monitor, balancer, current sense and hardware protector |
| Cell count | 6 to 16 cells in series |
| ADC accuracy | Plus or minus 1.5 mV on cell voltage |
| Conversion time | Full stack in less than 200 microseconds |
| Balancing current | Up to 240 mA per cell with external resistors |
| Communication | Isolated differential daisy chain, ring or stack arrangement |
| Current sense | Integrated, for pack current and fuse or relay monitoring |
| Supply output | 5 V LDO to power an external digital isolator |
| Safety | Developed for functional safety, systematic capability up to ASIL D |
| Qualification | AEC-Q100 grade 1, minus 40 to 125 C, HBM level 2, CDM level C4B |
| Package | HTQFP, 64 pins, 10.00 mm by 10.00 mm |
| Ordering | BQ79656PAPRQ1, 1000 pieces per reel, nickel palladium gold finish |
Reading a stack while the load is switching
A pack in an electric vehicle is never quiet. The inverter switches at tens of kilohertz, the current steps by hundreds of amps, and the cell voltage that a monitor sees includes the drop across the busbar and the wiring. A monitor that averages over a long window hides the noise but also hides the event.
This part converts the whole stack in under 200 microseconds and applies a filter after the conversion, so all cells are measured in the same window and the differential voltage between cells is meaningful. That is what makes a cell voltage reading usable for balancing decisions: two cells measured a few hundred microseconds apart at different load currents are not comparable.
Filtering on the cell input, before the ADC, is still needed. The resistor and capacitor at each input form a low pass network that keeps switching noise out of the converter, and the value of that network has to sit between what the ADC needs for accuracy and what the balancing path can tolerate. Change one and the other moves.
The protector inside, and why the host is not in that path
The hardware protector compares cells against thresholds in silicon and drives an output without asking the host. That matters in a system where the host runs an operating system, because the time between a cell going high and the host acting on it is measured in milliseconds at best, and a cell at the limit does not wait.
Balancing at 240 mA per cell is enough for a pack of a few tens of amp hours when the imbalance is small. Above that, an external bleed path is added and the part drives it. The decision of when to balance belongs to the host, and the data it needs comes from the measurement chain described above.
The isolated daisy chain is where most of the integration work sits. Each device has to be addressed, the ring has to survive a broken link, and the host has to know whether it is talking to device three or device seven. A pack that reports the wrong cell count after a service repair is usually a chain that has been rewired in a different order.
Where it fits in a build
Hybrid and electric powertrains, stationary storage with a battery management system, and larger e bike or scooter packs that need automotive grade parts. The 64 pin HTQFP with an exposed pad means the thermal path is part of the footprint, not an afterthought.
Automotive programmes run on supplier quality records for a decade. For a monitor that carries an ASIL claim, the supplier onboarding checklist page sets out what a source has to show about traceability and change notification before a part enters a build.
The sourcing side of this part is covered on the supplier quality audit. For a monitor that carries a functional safety claim, that page covers what we ask about traceability and change notification.
Questions we get on this code
Can it be used on a 12 cell pack? Yes, the part supports six to sixteen cells, and the unused inputs are tied together as described in the data sheet. The sixteen cell version also covers the shorter stacks without a different part number.
Does it need an external isolator? The daisy chain crosses a barrier between the pack side and the host side, and the part provides a 5 V rail to power the isolator. The isolator itself is a separate component.
What is the point of the SPI master? It lets the device talk to sensors on the pack side, such as a shunt monitor or a temperature hub, without a second isolated path to the host.
Is the part a drop in replacement for the 14 cell and 12 cell members of the family? They share the package and the pinout, and they differ in the maximum cell count. The board can be common, the configuration is not.