BQ77PL900DLR
Product Specifications
BQ77PL900DLR
Texas Instruments — Power Management & Signal Chain
Product Overview
The BQ77PL900DLR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
BQ77PL900DLR: a five to ten cell protector that also acts as an analog front end
The BQ77PL900DLR is a protector for packs of five to ten cells in series built around a P channel FET drive, with an I2C interface that lets a host controller read the cell voltages and change the protection settings. That second role is what separates it from the fixed protectors in the same catalogue: it can be the analog front end for a host that owns the protection logic.
The part runs from a pack supply of 7 V to 50 V and draws 450 microamps typical, which is high for a protector and normal for a front end that is measuring all the time. Two low dropout regulators are inside, one at 5 V and one at 3.3 V, both rated at 25 mA, so the board can be powered from the pack without a separate supply chain.
Settings live in an internal EEPROM. Voltage protection thresholds, detection delay times and the current limits are written once and then applied by the part on its own, which means the pack still protects itself when the host is asleep or has failed.
Key data for the BQ77PL900DLR
| Function | Pack protector and analog front end with host interface |
| Cell count | 5, 6, 7, 8, 9 or 10 cells in series |
| Supply range | 7 V to 50 V pack voltage |
| Supply current | 450 microamps typical |
| FET drive | P channel drive for charge and discharge |
| Interface | I2C to a host controller |
| Settings storage | Internal EEPROM for thresholds and delays |
| Regulators | 5 V at 25 mA and 3.3 V at 25 mA, both integrated |
| Measurement | Cell voltages and temperature read by the host over the bus |
| Package | SSOP, 48 pins |
| Temperature | Minus 40 to 100 C operating |
| Ordering | bq77PL900DLR, large tape and reel |
What an analog front end changes about the product
With a fixed protector, the pack decides everything and the host only learns that something happened. With this part, the host can read each cell, compute a state of charge, log a history and decide when to balance. The protection still runs inside the part from the EEPROM settings, so a host that hangs does not leave the pack unprotected.
That split is the right one for a product that needs both: a battery with a display, a medical cart that reports its state to a nurse call system, a backup unit that has to say how much runtime is left. In each case the host wants data, and the pack cannot wait for the host to provide protection.
The cost is complexity in the bus. Every read is a transaction that can fail, and every write to the EEPROM is a change to the protection behaviour of a pack that may already be in the field. A product that lets a service tool write thresholds needs a signed image or a password, not just a bus.
The two regulators, and the trap in using them
A 5 V and a 3.3 V regulator inside the part look like free power for the rest of the board. The catch is that they are fed from the pack, and the pack is exactly the node that goes away when the protection opens. A host powered from the 3.3 V rail will lose power at the moment it most wants to report why.
The 25 mA rating also sets what can be hung on them. A radio that draws 120 mA in transmit cannot be fed from this rail, and a display backlight will brown out the host every time it turns on. The usual arrangement is to use the internal regulators for the measurement and logic only, and to bring a separate converter for anything with a load that steps.
Thermal behaviour matters too. Dropping a 50 V pack to 3.3 V at 25 mA is about 1.2 W in the package, which is more than a 48 pin SSOP will dissipate comfortably at 85 C ambient. Packs that run near the top of the supply range should use the regulators at low current or not at all.
Where it fits in a build
Five to ten cells with a host that wants data is the shape of medical carts, floor cleaning machines, backup power units and light industrial vehicles. The part is also a common replacement target when an older front end goes obsolete, because its registers and its P channel drive follow a long established pattern.
Those replacements are where a pin compatible claim has to be tested rather than trusted. The obsolete part cross reference hub page sets out how we compare an end of life front end against a candidate on the register map, the drive polarity and the EEPROM defaults before anything is sampled.
The sourcing side of this part is covered on the supplier onboarding checklist. For a front end that may be a replacement for an older part, that page covers what a source has to show before the part enters a line.
Questions we get on this code
Can it work without a host? Yes. The EEPROM settings are applied by the part, and the protection works from the moment the pack is connected. The host only adds measurement and logging.
Is the EEPROM written at the factory? It comes with defaults that have to be checked against the pack specification. A production line that relies on the default settings is relying on a document, not on a test.
Does it balance the cells? No. There is no bleed path. Balancing has to be added as a resistor network with its own control, either from the host or from a separate part.
What replaces it if the part is discontinued? Nothing is pin compatible across the whole function. A replacement generally means a monitor with cell measurement plus a separate protector, which changes the board and the host code together.