Contact Us

BQ7790400PWR

Brand: Texas Instruments
Texas Instruments BQ7790400PWR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

BQ7790400PWR — Power Management & Signal Chain | Superb Automation

BQ7790400PWR

Texas Instruments — Power Management & Signal Chain

Product Overview

The BQ7790400PWR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

BQ7790400PWR: a stackable protector for 3 to 20 series cells

The BQ7790400PWR is a low power protector for packs from three to twenty cells in series, and its distinguishing feature is that the cell count is set by how many devices are stacked rather than by which option is bought. Each device covers a group of cells, and the charge and discharge outputs of one device are wired into the control inputs of the next, so a twenty cell pack is built from several parts on one board.

It protects on voltage, current and temperature, and it looks for open sense wires. The voltage comparators hold plus or minus 10 mV over the overvoltage range of 3 V to 4.575 V and the undervoltage range of 1.2 V to 3 V. Current protection works from the voltage across the sense resistor, with a first and second discharge overcurrent point, a short circuit point and a charge overcurrent point.

The 00 option is specified with a 4.225 V overvoltage threshold, a two second overvoltage delay, a 2.2 V undervoltage threshold with a two second delay and 400 mV of undervoltage hysteresis, a 60 mV second discharge overcurrent point at 350 ms and a 100 mV short circuit point.

Key data for the BQ7790400PWR

FunctionVoltage, current, temperature and open wire protection with FET drivers
Cell count3 to 20 cells in series, extended by stacking devices
Overvoltage range3 V to 4.575 V, 4.225 V on the 00 option
Undervoltage range1.2 V to 3 V, 2.2 V on the 00 option with 400 mV hysteresis
Voltage accuracyPlus or minus 10 mV
Overcurrent pointsTwo discharge levels, one charge level and a short circuit level
Current accuracyPlus or minus 20 percent at or below 20 mV, plus or minus 30 percent above
Temperature protectionCharge and discharge, over and under, thresholds set by option
Open wireDetection on the cell sense inputs
FET driveIndependent low side NMOS drivers for charge and discharge
Supply current6 microamps in normal mode
Package20 pin TSSOP, 6.50 mm by 4.40 mm
TemperatureMinus 40 to 85 C operating

Stacking, and why the wiring between devices matters

In a stacked arrangement, each device sees the cells in its own group and passes a decision to the device below it. The charge and discharge pins of the upper device connect to the control inputs of the lower one, so one overvoltage anywhere in the stack turns off the whole string. That is the behaviour a pack needs, and it depends entirely on those two wires being correct.

The wiring has to cross a voltage boundary. The upper device sits at a potential hundreds of volts above the lower one, and the two control signals have to cross that boundary without turning the lower device on when the upper one is unpowered. The usual arrangement is a level shift with a resistor and a clamp, and its failure mode is a pack that will not charge with no obvious fault.

Cell group size sets the resolution of the protection. A device that covers eight cells will protect the string at the level of the highest cell in its group, but the group boundary has to be placed where the harness is short and the cells are physically together. Groups that cut across a connector are the ones that produce strange readings.

Current protection from a sense resistor, and what the tolerance really means

The overcurrent comparators work on the voltage across the pack sense resistor, which means the current limit in amps depends on the resistor value and its tolerance. A 1 milliohm resistor at 60 mV gives 60 amps, and a 5 percent resistor moves that by 3 amps before the comparator error is counted. The comparator error is quoted as plus or minus 20 percent at or below 20 mV, which is the range where most of the second level points sit.

That tolerance is wide because the threshold is small. At 60 mV the error is plus or minus 30 percent, so the same part can trip anywhere from 42 to 78 amps. A product that needs a tight current limit has to use a larger sense resistor so the threshold sits higher in the range, or accept the spread and size the FETs for the upper end.

The short circuit point is a different job. It is there to protect the FETs during a hard fault, and it acts in milliseconds. The delay for the short circuit on the 00 option is set by the option, and it is short enough that the FET safe operating area, not the load, decides whether the pack survives.

Where it fits in a build

This is the protection layer for light electric vehicle packs, e bike packs and small storage modules where the series count is above the range of a single chip protector. It also suits packs that need current protection without a full monitor, because the current comparators are inside the part.

Six microamps in normal mode is what makes it usable on a pack that is stored for months. For a programme that holds these parts across several pack builds, the strategic sourcing page sets out how the supply is held over a long programme and how a second source is qualified.

The sourcing side of this part is covered on the BOM scrubbing. For a pack whose protection depends on a sense resistor and a stack of options, that page covers how a bill of material is checked before release.

Questions we get on this code

How many devices can be stacked? The limit is set by the isolation of the control signals between stages, not by the part. Twelve cells per device is the top of the range and the string can be extended past twenty cells, but each extra stage adds a level shift and a failure point.

Does it need a microcontroller? No. The part is standalone and the thresholds are fixed by the option. A host can read the fault pins if it wants a log, but nothing in the protection path depends on the host being alive.

Can the charge and discharge FETs be shared with another protector? Not safely. Two devices driving the same gate will fight each other, and the one with the lower drive wins in a way that is not repeatable. Use one protector per gate.

What happens when the option thresholds do not match the cells? The pack either trips early, which loses capacity, or trips late, which is worse. The option table has to be read against the cell specification before the part number is fixed, and the 00 option is only correct for cells that are charged to about 4.2 V with a 2.2 V discharge floor.